Dahua Technology Ultra IPC-HFW7442H-Z Manuel utilisateur

Model H IR Bullet

Network Camera

Quick Start Guide

V1.0.1

ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Dahua Ultra IPC-

HFW7442H-Z o cerca il tuo prodotto tra le migliori offerte di Videosorveglianza

Foreword I

Foreword

General

This manual introduces the functions, installation, and operations of the camera.

Safety Instructions

The following categorized signal words with defined meaning might appear in the manual.

Signal Words

Meaning

WARNING

Indicates a medium or low potential hazard which, if not avoided,

could result in slight or moderate injury.

CAUTION

Indicates a potential risk which, if not avoided, could result in

property damage, data loss, lower performance, or unpredictable

result.

NOTE

Provides additional information as the emphasis and supplement

to the text.

Revision History

Version

Revision Content

Release Time

V1.0.1

Change the pictures of Figure 1-1.



Delete the mode the Angle-mounted



installation type in "3.3.1 Installation

Type."

Add "3.3.3 Threading Cable" and



"3.3.5 Wrapping Waterproof Tape

(Optional)."

April 2019

V1.0.0

First release.

November 2018

Privacy Protection Notice

As the device user or data controller, you might collect personal data of others such as face,

fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be

in compliance with the local privacy protection laws and regulations to protect the legitimate

rights and interests of other people by implementing measures include but not limited to:

providing clear and visible identification to inform data subject the existence of surveillance

area and providing related contact.

About the Manual

The Manual is for reference only. If there is inconsistency between the manual and the

actual product, the actual product shall prevail.

Foreword II

We are not liable for any loss caused by the operations that do not comply with the manual.

The manual would be updated according to the latest laws and regulations of related

regions. For detailed information, see the paper manual, CD-ROM, QR code or our official

website. If there is inconsistency between paper manual and the electronic version, the

electronic version shall prevail.

All the designs and software are subject to change without prior written notice. The product

updates might cause some differences between the actual product and the manual. Please

contact the customer service for the latest program and supplementary documentation.

There still might be deviation in technical data, functions and operations description, or

errors in print. If there is any doubt or dispute, please refer to our final explanation.

Upgrade the reader software or try other mainstream reader software if the manual (in PDF

format) cannot be opened.

All trademarks, registered trademarks and the company names in the manual are the

properties of their respective owners.

Please visit our website, contact the supplier or customer service if there is any problem

occurred when using the device.

If there is any uncertainty or controversy, please refer to our final explanation.

Important Safeguards and Warnings III

Important Safeguards and Warnings

Electrical Safety

All installation and operation should conform to your local electrical safety codes.

The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and

supply power with rated voltage which conforms to Limited power Source requirement

according to IEC60950-1. Please note that the power supply requirement is subject to the

device label.

Make sure the power supply is correct before operating the device.

A readily accessible disconnect device shall be incorporated in the building installation

wiring.

Prevent the power cable from being trampled or pressed, especially the plug, power socket

and the junction extruded from the device.

Environment

Do not aim the device at strong light to focus, such as lamp light and sun light; otherwise it

might cause over brightness or light marks, which are not the device malfunction, and

affect the longevity of Complementary Metal-Oxide Semiconductor (CMOS).

Do not place the device in a damp or dusty environment, extremely hot or cold

temperatures, or the locations with strong electromagnetic radiation or unstable lighting.

Keep the device away from any liquid to avoid damage to the internal components.

Keep the indoor device away from rain or damp to avoid fire or lightning.

Keep sound ventilation to avoid heat accumulation.

Transport, use and store the device within the range of allowed humidity and temperature.

Heavy stress, violent vibration or water splash are not allowed during transportation,

storage and installation.

Pack the device with standard factory packaging or the equivalent material when

transporting the device.

Install the device in the location where only the professional staff with relevant knowledge

of safety guards and warnings can access. The accidental injury might happen to the

non-professionals who enter the installation area when the device is operating normally.

Operation and Daily Maintenance

Do not touch the heat dissipation component of the device to avoid scald.

Carefully follow the instructions in the Guide when performing any disassembly operation

about the device; otherwise, it might cause water leakage or poor image quality due to

unprofessional disassemble. Please contact after-sale service for desiccant replacement if

there is condensed fog found on the lens after unpacking or when the desiccant turns

green. (Not all models are included with the desiccant).

Important Safeguards and Warnings IV

It is recommended to use the device together with lightning arrester to improve lightning

protection effect.

It is recommended to ground the device to enhance reliability.

Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with air

blower, or you can wipe the lens gently with soft cloth that moistened with alcohol.

Device body can be cleaned with soft dry cloth, which can also be used to remove

stubborn stains when moistened with mild detergent. To avoid possible damage on device

body coating which could cause performance decrease, do not use volatile solvent such as

alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive

detergent be used.

Dome cover is an optical component, do not touch or wipe the cover with your hands

directly during installation or operation. For removing dust, grease or fingerprints, wipe

gently with moisten oil-free cotton with diethyl or moisten soft cloth. You can also air blower

to remove dust.

Please strengthen the protection of network, device data and personal information by

adopting measures which include but not limited to using strong password, modifying

password regularly, upgrading firmware to the latest version, and isolating computer

network. For some device with old firmware versions, the ONVIF password will not be

modified automatically along with the modification of the system password, and you need

to upgrade the firmware or manually update the ONVIF password.

Use standard components or accessories provided by manufacturer and make sure the

device is installed and maintained by professional engineers.

The surface of the image sensor should not be exposed to laser beam radiation in an

environment where a laser beam device is used.

Do not provide two or more power supply sources for the device unless otherwise specified.

A failure to follow this instruction might cause damage to the device.

Regulatory Information V

Regulatory Information

The regulatory information herein might vary according to the model you purchased. Some

information is only applicable for the country or region where the product is sold.

FCC Information

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

FCC conditions:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause

undesired operation.

FCC compliance:

This equipment has been tested and found to comply with the limits for a digital device,

pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communication.

For class A device, these limits are designed to provide reasonable protection against

harmful interference in a commercial environment. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

For class B device, these limits are designed to provide reasonable protection against

harmful interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

Table of Contents VI

Table of Contents

Foreword.................................................................................................................................................... I

Important Safeguards and Warnings.................................................................................................... III

Regulatory Information............................................................................................................................V

1 Introduction............................................................................................................................................ 1

Device Ports.................................................................................................................................. 11.1 Connecting Alarm Input/output ..................................................................................................... 21.2

2 Network Configuration.......................................................................................................................... 4

Initializing Device .......................................................................................................................... 42.1 Modifying Device IPAddress........................................................................................................ 52.2 Logging in Web Interface.............................................................................................................. 62.3

3 Installation.............................................................................................................................................. 7

Packing List................................................................................................................................... 73.1 Dimension..................................................................................................................................... 73.2 Installing Device............................................................................................................................ 83.3 3.3.1 Installation Type.................................................................................................................. 8

3.3.2 Installing SD Card (Optional).............................................................................................. 8

3.3.3 Threading Cable................................................................................................................. 8

3.3.4 Attaching Device................................................................................................................. 9

3.3.5 Wrapping Waterproof Tape (Optional)...............................................................................11

3.3.6 Adjusting Sunshade Cap.................................................................................................. 12

3.3.7 Adjusting Lens Angle........................................................................................................ 13

Introduction 1

1 Introduction

Device Ports1.1

Device ports might vary with different models, and the actual product shall prevail.

Do waterproof to all the cable joints with insulating tape and waterproof tape to avoid short

circuit and water damage. For the detailed operation, see the FAQ Manual.

Device portsFigure 1-1

For more information about device ports, see Table 1-1.

Table 1-1 Device ports information

No.

Port Name

Function

RS-485_A, controls external devices, such as PTZ.

RS-485_B, controls external devices, such as PTZ.

Ground connection of port I1, port I2 and port I3..

Receives the switch signal of external alarm source.

Outputs alarm signal to alarm device.

N1/N2: Normally opened alarm output port.



C1/C2: General alarm output port.



You can only connect N1 to C1, and N2 to C2.

Outputs 12V DC 2W power. P is for positive pole, and G is

for negative pole.

G (close to P)

AUDIO OUT

3.5 mm port, and can connect to speaker to output audio

signal.

AUDIO IN

3.5 mm port, and can connect to sound-pick-up device to

receive audio signal.

LAN / OPT

LAN: Connects to network with network cable;



provides power to the device with PoE.

OPT: Connects to OPT devices to connect to the



network.

Introduction 2

No.

Port Name

Function

DC 12V or AC

24V

Inputs 12V DC or 24VAC power. Please be sure to supply

power as instructed in the Guide.

Device abnormity or damage could occur if power is not

supplied correctly.

VIDEO

Outputs analog video signal.

Connecting Alarm Input/output1.2

Alarm input/output is available on select models.

Connect alarm input device to the alarm input end of the I/O port.Step 1 Device collects different states of alarm input port when the input signal is idling and

being connected to the ground.

Device collects logic "1" when input signal is connecting to +3V to +5V or idling.

Device collects logic "0" when input signal being connected to the ground.

Alarm inputFigure 1-2

Connect alarm output device to the alarm output end of the I/O port. The alarm outputStep 2 is relay switch output, which can only connect to NO alarm devices.

The ALARM_OUT port and the ALARM_OUT_GND port with the same number

constitute a switch for alarm output. See Figure 1-3. The switch is open normally and

closes when there is alarm output. Alarm outputFigure 1-3

The alarm input in the web interface is corresponding to the alarm input end of the

I/O port. There will be high level and low level alarm signal generated by the alarm

input device when alarm occurs, set the input mode to "NO" (default) if the alarm

Introduction 3

input signal is logic "0" and to "NC" if the alarm input signal is logic "1".

The alarm output in the web interface is corresponding to the alarm output end of

the device, which is also alarm output end of the I/O port.

Table des matières

Autres manuels Dahua Technology Caméra de sécurité

Dahua Technology

Dahua Technology N28BL7Z Manuel utilisateur

Dahua Technology

Dahua Technology IPC-HFW1320S-W Manuel utilisateur

Dahua Technology

Dahua Technology Pro IPC-HDW5241TM-AS Manuel utilisateur

Dahua Technology

Dahua Technology 59230UNI Manuel utilisateur

Dahua Technology

Dahua Technology IPC-HFW2431DG-4G Manuel utilisateur

Dahua Technology

Dahua Technology DH-IPC-HFW4X-W Manuel utilisateur

Dahua Technology

Dahua Technology IPC-HDBW1531E-S-0280B Manuel utilisateur

Dahua Technology

Dahua Technology Eyeball Manuel utilisateur

Dahua Technology

Dahua Technology N42BD32 Manuel utilisateur

Dahua Technology

Dahua Technology HD IR Mini Bullet Manuel utilisateur

Dahua Technology

Dahua Technology D-SD6C3432XB-HNR-AGQ-PV Manuel utilisateur

Dahua Technology

Dahua Technology NAVIGATOR X1550 Manuel utilisateur

Dahua Technology

Dahua Technology DH-IPC-PFW83242-A180-S2 Manuel utilisateur

Dahua Technology

Dahua Technology DH-IPC-HFW11A0SN-W Manuel utilisateur

Dahua Technology

Dahua Technology IPC-HDW2249TM-S-IL-0280B Manuel utilisateur

Dahua Technology

Dahua Technology D-IPC-HDBW3441F-AS-M-0360B Manuel utilisateur

Dahua Technology

Dahua Technology 6CE230UNI Manuel utilisateur

Dahua Technology

Dahua Technology N82AL32 Manuel utilisateur

Dahua Technology

Dahua Technology IPC-MBW4231-AS/M12 Manuel utilisateur

Dahua Technology

Dahua Technology N55BS5 Manuel utilisateur

Dahua Technology

Dahua Technology IPC-HFW5431E-Z Manuel utilisateur

Dahua Technology

Dahua Technology IPC-HUM4431S-L4 Manuel utilisateur

Dahua Technology

Dahua Technology IPC-HDW2431T-AS-S2 Manuel utilisateur

Dahua Technology

Dahua Technology IPC-HFW1230S1-0280B-S5 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur