D-Link Express Ethernetwork DI-704P Manuel utilisateur
Before You Begin
1. If you purchased this router to share your high-speed Internet connection with
other computers, you must have an Ethernet-based Cable/DSL modem with an
established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for
configuring the DI-704P router. The DI-704P Router acts as a DHCP server and
will assign all the necessary IP address information on your network. See
Appendix at the end of this Quick Installation Guide or the Manual on the
CD-ROM for setting each network adapter to automatically obtain an IP
address.
Check Your Package Contents
These are the items included with your DI-704P purchase:
©2002 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
holders. Software and specifications subject to change without notice. DI-604.05082002
This product can be set up using any current
web browser, i.e., Internet Explorer 5x,
Netscape Navigator 4x.
DI-704P
Express EtherNetwork™
Broadband Route
r
• DI-704P Ethernet Broadband Router
• CD-ROM (containing Manual and Warranty)
• Ethernet (CAT5 UTP/Straight-Through) Cable
• 5V DC, 2A Power Adapter
Using a power
supply with a
different voltage rating
will damage and void
the warranty for this
product.
If an
y
of the above items are missin
g
,
p
lease contact
y
our reseller.
Connecting The DI-704P Broadband
Router To Your Network
A. First, connect the power adapter to the receptor at the side panel of
the DI-704P and then plug the other end of the power adapter to a
wall outlet or power strip. The Power LED will turn ON to indicate
proper operation.
B. Insert one end of an Ethernet cable to the WAN port on the back
panel of the DI-704P and the other end to the Ethernet port located on
your Cable or DSL modem. The WAN LED light will illuminate to
indicate proper connection.
C. Insert one end of an Ethernet cable to LAN port 1 on the back panel
of the DI-704P and the other end to the Ethernet port on the network
adapter in the computer you will use to configure the DI-704P. The
LED light for LAN Port 1 will illuminate to indicate proper connection.
(Note: Some computers already have network adapters pre-installed.)
D. The parallel port on the DI-704P is used to connect printers only.
Connect one end of the printer cable to your printer and the other end
to the DI-704P.
Restart Your Computer
C.LAN Ports
These are the
connections for
Ethernet cables to
your Ethernet-
enabled com
p
uters
A.Receptor for
Power Adapter
is located on the
side.
Reset Button
Pressing this button
restores the router
to its original factory
default settings.
B.WAN Port
This is the
connection for the
Ethernet Cable to
the Ethernet Port on
the Cable or DSL
Modem.
D.Printer Port
You can connect a
Printer to the
Parallel Port here.
Connecting Additional Computers To The
DI-704P Broadband Router
Using additional Ethernet (CAT5 UTP/Straight-Through) cables, connect
your Ethernet-equipped computer(s) to one of the 3 remaining Ethernet
LAN ports on the back panel of the DI-704P.
When you have completed the steps in this Quick Installation Guide, your
connected network should look similar to this:
LAN Port LEDs. Each of the
LAN ports on the back of the
DI-704P have a corresponding
LED light on the front panel of
the unit. When a proper
connection has been made to
a computer that is ON, the
LED on the front panel should
illuminate.
Cable or DSL
Modem
DI-704P Ethernet
Broadband Router
Computers connected
to the LAN Ports
Connect a printer
to the parallel port
For optional printer setup, please refer to
the DI-704P’s Manual
Using The Setup Wizard
The logon pop-up
screen will appear.
Once you have
logged in, the
Home screen
will appear.
Open your Web
browser and type
“http://192.168.0.1” into
the URL address box.
Then press the Enter or
Return key.
Type “admin” for the
username and leave the
password field blank.
Click OK
DI-704P
Click Run Wizard
You will see the following
screens.
Set password.You have the option to establish a new admin password for the DI-704P
Click Next
Click Next
The Setup Wizard (continued)
Select the type of Internet connection for your router.
If you selected Dynamic
IP Address, this screen
will appear:
If you are unsure of which setting to
select, please contact your Internet
Service Provider.
What is a MAC address? Each
network adapter has a discrete
Media Access Control (MAC)
address. Note that some computers
and peripherals may already include
built-in network adapters.
Click Next
Click Next
Click the “Clone MAC
Address” button to
automatically copy the MAC
address of the network adapter
in your computer. You can also
manually type in the MAC
address.
Select one of
these settings
If your ISP requires a
Static IP Address, and
this option is selected,
then this screen will
appear:
If your ISP uses PPPoE
(Point-to-Point Protocol
over Ethernet) and this
option is selected, then
this screen will appear:
Enter in the username
and password provided
to you by your ISP.
Do not use
the numbers
displayed in these
fields. They are only
shown as an example.
Click Next
Enter the IP address
information originally
provided to you by your ISP.
You will need to complete all
the required fields.
Click Next
Your Setup is Complete!
Test Your Internet Connection
Relaunch your Web
browser (i.e., Internet
Explorer or Netscape
Navigator), to link to your
favorite Web site to test
your Internet connection.
For additional settings or
information, refer to the
Advanced, Tools, or
Status tabs on the web-
management
interface; or to the
manual located on the
CD-ROM.
Click the
to Exit
Click Restart
For optional Printer setup please refer to
the DI-704P’s Manual.
APPENDIX
To connect to the network, make sure
the network adapter in your computer
is configured properly. Here’s how to
configure the network adapter to obtain
an IP address automatically for the
DI-704P Broadband Router.
For Microsoft Windows XP:
Go to Start > right click on
My Network Places >
select Properties > Double-click on
the Network Connection associated
with the Ethernet adapter (i.e.,
D-Link DFE-530TX+).
Click Internet Protocol (TCP/IP)
Click Properties
Select Obtain an IP address
automatically
Click OK
Restart your
computer
For Apple Macintosh OS X:
Go to the Apple Menu
and Select System
Preferences.
The IP address information,
the Subnet Mask, the Router’s
IP address and the Ethernet
adapter address will appear.
Click on
Network
Select Built-in
Ethernet in the Show
pull-down menu
Select Using DHCP
in the Configure pull-
down menu
Click on
Apply Now
Autres manuels pour Express Ethernetwork DI-704P
8
Table des matières
Autres manuels D-Link Routeur réseau
D-Link
D-Link DES-1210-52/ME Mode d’emploi
D-Link
D-Link DSL-2640U Manuel utilisateur
D-Link
D-Link DI-2621 Manuel utilisateur
D-Link
D-Link DWR-555 Manuel utilisateur
D-Link
D-Link M15-2PK Manuel utilisateur
D-Link
D-Link DSR-150 Manuel utilisateur
D-Link
D-Link AirPlusXtremeG DI-624 Mode d'emploi
D-Link
D-Link DSL-524T Manuel utilisateur
D-Link
D-Link DSL-G2452GE Manuel utilisateur
D-Link
D-Link DGS-105 - Switch Manuel utilisateur
D-Link
D-Link AirPremier DWL-1800 Manuel utilisateur
D-Link
D-Link DSL-524T Manuel utilisateur
D-Link
D-Link DWR-980 Manuel utilisateur
D-Link
D-Link DSG-1100-10/ME Manuel utilisateur
D-Link
D-Link DES-1005D Manuel utilisateur
D-Link
D-Link DWR-932 Manuel utilisateur
D-Link
D-Link DSL-2650U Manuel utilisateur
D-Link
D-Link DSL-2640B Manuel utilisateur
D-Link
D-Link DWM-312W Manuel utilisateur
D-Link
D-Link DIR-X1530 Manuel utilisateur
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité