D-Link DGE-660TD Manuel utilisateur

D-Link DGE-660TD Installation Guide 2

This Installation Guide includes instructions for:

• Windows Vista™

• Windows®XP

• Windows®2000

Installation Guide Contents

Section 1: Pre-Installing the Windows®Vista™, XP, and 2000

Section 2: Insert the DGE-660TD into your Laptop

Section 3: Finishing the Windows®Installation

Package Contents

Verify that your D-Link DGE-660TD package contains the

following items. If any items are missing, please contact your

reseller.

• D-Link DGE-660TD

• Drivers on CD-ROM

• Manual on CD-ROM

!For Windows®Vista/XP/2000:

Run the Install CD BEFORE installing the

DGE-660TD into your laptop.

D-Link DGE-660TD Installation Guide3

Installing the Driver

• With your computer ON, insert the Driver CD of the

DGE-660TD into your CD-ROM Drive.

• The Autorun Screen will appear as shown here.

• Select “Install Drivers” to install the drivers onto your

computer.

• After a few moments, the “Install Finish” screen will appear.

Click “OK”.

• Select “Yes,” if you are prompted to restart your computer.

Restart the computer manually if the prompt does not occur.

(Go to Start > Shut down > Restart.)

D-Link DGE-660TD Installation Guide 4

Insert the Adapter

This section refers to all users, regardless of which operating

system you use.

NOTE: You must ﬁrst install the drivers as explained in

Section 1.If you have not done this and you have inserted the

DGE-660TD into the Cardbus slot, you will need to cancel

the New Hardware Wizard, and start over at the beginning

of this installation guide.

• Insert the DGE-660TD into the Cardbus slot of your laptop.

• Gently insert the front end of the DGE-660TD into the Cardbus

slot on your laptop until it is ﬁrmly seated. Make sure that the

card is face-up, as shown. Do not force the insertion.

• Connect an Ethernet Cable (CAT5) from a switch or hub to

the DGE-660TD.

D-Link DGE-660TD Installation Guide5

Finishing the Installation

To complete the installation of the DGE-660TD:

• Make sure that the DGE-660TD CD-ROM is

inserted in the CD-ROM drive

• The DGE-660TD is inserted into your laptop

• The laptop is turned ON

• See the section below that corresponds to your

Operating System to complete the installation:

Windows Vista™Users

Windows Vista™completes the installation of the DGE-660TD

automatically. An “Installing device driver software” message

will appear in the task bar to indicate that the installation is in

progress.

D-Link DGE-660TD Installation Guide 6

Windows®XP Users

Windows®XP completes the installation of the DGE-660TD

automatically. A “Found New Hardware” message will appear in

the task bar to indicate that the installation is complete.

Windows®2000 Users

Windows®2000 completes the installation of the DGE-660TD

automatically. When the “hour glass” disappears, the installation

is complete.

D-Link DGE-660TD Installation Guide7

Verify Installation

Step 1:

Windows®2000: Click on Start > Settings > Control Panel

Windows®XP: Click on Start > Control Panel

Windows Vista™: Click on Start > Control Panel

Step 2:

Windows®2000 and XP: Click on the System icon. Click the

Hardware tab and then click Device Manager.

Windows Vista™: Click on System and Maintenance and then

click on Device Manager.

Step 3:

Scroll down and click the plus (+) sign next to Network Adapters.

The D-Link DGE-660TD Gigabit CardBus PC Card will be

listed.

D-Link DGE-660TD Installation Guide 8

Conﬁgure your Adapter

After you install your new D-Link adapter, by default, the TCP/IP

settings should be set to obtain an IP address from a DHCP

server (i.e router) automatically. To verify your IP address,

please see follow the steps below:

Windows®2000/XP: Click on Start > Run. In the run box type

cmd and click OK.

Windows Vista™: Click on Start > All Programs > Accessories

> Command Prompt.

At the prompt, type ipconﬁg and press Enter.

This will display the IP address, subnet mask, and the default

gateway of your adapter.

If the address is 0.0.0.0, check your adapter installation, security

settings, and the settings on your router. Some ﬁrewall software

programs may block a DHCP request on newly installed

adapters.

D-Link DGE-660TD Installation Guide9

If you are not using a DHCP capable gateway/router, or you need

to assign a static IP address, please follow the steps below.

Step 1

Windows®2000: Click on Start > Settings > Control Panel >

Network Connections.

Windows®XP : Click on Start > Control Panel > Network

Connections.

Windows Vista™: Click on Start > Control Panel > Network and

Internet > Network and Sharing Center > Manage network

connections.

Step 2

Right-click on Local Area Connection which represents your

D-Link network adapter and select Properties.

Step 3

Highlight Internet Protocol (TCP/IP) and click Properties.

Step 4

Click Use the following IP address and enter an IP address

that is on the same subnet as your network or the LAN IP

address on your router.

D-Link DGE-660TD Installation Guide 10

Example: If the router’s LAN IP address is 192.168.0.1, make

your IP address 192.168.0.X where X is a number between 2

and 99. Make sure that the number you choose is not in use

on the network. Set Default Gateway the same as the LAN IP

address of your router (192.168.0.1).

Set Primary DNS the same as the LAN IP address of your router

(192.168.0.1). The Secondary DNS is not needed or you may

enter a DNS server from your ISP.

Step 5

Click OK twice to save your settings.

Autres manuels pour DGE-660TD

Table des matières

Autres manuels D-Link Adaptateur

D-Link

D-Link DHP-P600AV Manuel utilisateur

D-Link

D-Link DHP-501AV Manuel utilisateur

D-Link

D-Link DWA-181 Manuel utilisateur

D-Link

D-Link AirPlus XTREME G+ DWL-G650+ Manuel utilisateur

D-Link

D-Link Air DWL-120 Manuel utilisateur

D-Link

D-Link DWL-G630 - AirPlus G 802.11g Wireless PC... Manuel utilisateur

D-Link

D-Link DVG-5121SP Manuel utilisateur

D-Link

D-Link DWA140 - RANGE BOOSTER N USB ADAPTOR Manuel utilisateur

D-Link

D-Link PowerLine DHP-302 Manuel utilisateur

D-Link

D-Link DFE-500TX ProFAST 10/100 Manuel utilisateur

D-Link

D-Link AirPlusXtremeG DWL-G650 Manuel utilisateur

D-Link

D-Link Air DWL-610 Manuel utilisateur

D-Link

D-Link DWA-132 Manuel utilisateur

D-Link

D-Link DWL-122 Manuel utilisateur

D-Link

D-Link DXE-810T Manuel utilisateur

D-Link

D-Link DUB-1312 Manuel utilisateur

D-Link

D-Link XTREME N DUAL BAND USB ADAPTER DWA-160 Manuel utilisateur

D-Link

D-Link DWA140 - RANGE BOOSTER N USB ADAPTOR Manuel utilisateur

D-Link

D-Link DWL-G820 - AirPlus Xtreme G Manuel utilisateur

D-Link

D-Link DVG-5102S Manuel utilisateur

D-Link

D-Link Air DWL-660 Manuel utilisateur

D-Link

D-Link DHP-700AV Manuel utilisateur

D-Link

D-Link DHP-328AV Manuel utilisateur

D-Link

D-Link DWA-556 Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur

RCA

RCA AH57R Manuel utilisateur