Cypress CMIR-44 Manuel utilisateur
CMIR-44
4 by 4 Infrared Matrix
Operation Manual
CMIR-44
Disclaimers
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes
no commitment to update or to keep current the information
contained in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
Copyright Notice
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means
- electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise - without express written permission and consent from
Cypress Technology.
© Copyright 2009 by Cypress Technology.
All Rights Reserved.
Version 1.0 February 2010
Trademark Acknowledgments
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
Safety Precautions
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
Always follow basic safety precautions to reduce the risk of
fire, electrical shock and injury to persons.
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
Do not attach the power supply cabling to building surfaces.
Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.
Revision History
Version No Date Summary of Change
V1 20100201 Preliminary Release
VR2 20101207 Adding IR Cable Distance
VR3 20120924 IR Frequency & Remote Control
Table of Contents
1
1
1
1
1
2
3
3
4
5
5
5
5
6
7
8
1. Introduction…………………………………………………........……….
2. Applications……………………..…………………………................….
3. Package Contents…………………………......…………….............…
4. System Requirements……...…………………..….…………........…….
5. Features…………………………………………….......……........………
6. Specications..………………………………………...........………...….
7. Hardware Description………………...……........….....................……
7.1 Front Panel ...............................................................................
7.2 Rear Panel …………………………………………..........…….…
8. IR Cable Pin Denitions………………...…….......….....................……
8.1 IR Receiver................................................................................
8.2 IR Blaster………………....…………………………..........…….…
8.3 IR Functioning Chart………………………………………………...
9. Remote Control …….………...................…………..........…..…..…...
10. Connection and Installation..................…………..........…..…..…...
11. Acronyms …….………...................…………..........…..…...........…...
1. Introduction
The Infrared 4 by 4 Matrix is designed to control your source devices from be-
side your display/receiver. Using the original remote, you can control DVD/
Blu-ray players, satellite and set-top-boxes and with a cross matrix design this
device gives the ability to send infrared signals from place to place. When
used with an HDMI/converter matrix, this brilliant product will allow you to
freely manage your sources and displays. Simply place the IR receiver near
the display and put the IR blaster in a position so that all devices will be able
to function properly, even when they are hidden in a cabinet or placed far
away. So if your looking for a way to extend IR control over great distances,
you have but one choice: The Infrared 4 by 4 Matrix
2. Applications
• Control multiple sources
• System Control
• Showroom control
3. Package Contents
• 4 by 4 Infrared Matrix
• Remote Control CR81-06F09 with battery
• 5V DC power adaptor
• Operation Manual
• 5xIR Receiver cables
• 5xIR Blaster cables
4. System Requirements
Source equipment: Display/ TV/monitors and HDMI/video matrix box devices.
5. Features
• Supports independent IR receiver and IR blaster selection and control
• This device does not send audio/video signals, it only transmits and
receives infrared signals to control equipment that is far away, using IR
extender cables.
• Supports a frequency of 30KHz ~ 50KHz.
• Use your existing remote controls.
1
6. Specications
IR Frequency 30KHz to 50KHz
Input port 4 x independent IR Blasters; 1 x total IR blaster control
Output port 4 x independent IR Receiver; 1 x total IR receiver control
Power Supply 5VDC/1A (US/EU standards, CE/FCC/UL certified)
ESD Protection Human body model: ±8kV (air-gap discharge)
±4kV (contact discharge)
Dimensions (mm) 180(W) x 124(D) x 25(H)
Weight(g) 450
Chassis Material Aluminum
Silkscreen Color Silver
Power Consumption 0.86W
Operating Temperature 0˚C~40˚C / 32˚F ~ 104˚F
Storage temperature -20˚C~60˚C / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (non-condensing)
2
7. Hardware Description
The following sections describe the hardware components of the unit.
7.1 Front Panel
1 2 3 4 5 6
qIR sensor: To control the system.
②POWER Button & LED: Press to turn the unit on or press it again to turn it to
standby mode. When the system is on the LED will be green, when in
STANDBY mode the LED will then be red.
③IR IN 1 & output LED: Press the button to select which output IR signal will
be sent, the LED will then illuminate according to the selection.
④IR IN 2 & output LED: Press the button to select which output IR signal will
be sent, the LED will then illuminate according to the selection.
⑤IR IN 3 & output LED: Press the button to select which output IR signal will
be sent, the LED will then illuminate according to the selection.
⑥IR IN 4 & output LED: Press the button to select which output IR signal will
be sent, the LED will then illuminate according to the selection.
3
7.2 Rear panel
1 2 3 4 5
qIR OUT ALL: This slot is where you connect the IR blaster cable included in
the package. Place the IR blaster in direct line-of-sight of the equipment
to be controlled for it will blaster out all signal received from IR IN 1~4.
②IR OUT A~D: These slots are where you connect the IR blaster
cables included in the package. Place the IR blaster in direct line-of-sight
of the equipment to be controlled for it will blaster out the signal choosen
by IR IN 1~4.
③IR IN ALL: This slot is where you connect the IR receiver cable included in
this package for IR signal reception. Ensure that remote being used is
within the direct line-of-sight of the IR receiver for it will send out the signal
to IR out A~D.
④IR IN 1~4: These slots are where you connect the IR receiver cables
included in the package remote control. Ensure that remote being used is
within the direct line-of-sight of the IR receiver for it will send out the signal
to the selected IR out from A~D and IR OUT ALL.
⑤DC 5V: Plug the 5V DC power supply into the unit and connect the
adaptor to an AC outlet.
4
8. IRCablePinDenitions
8.1 IR Receiver 8.2 IR Blaster
IR Receiver
① IR signal
② Power 5V
③ Grounding
① ② ③
IR Blaster
① ②
① Power 5V
② IR Blaster Signal
③ NC
③
Note: Both the IR Receiver & Blaster can support a frequency of
30~50KHz.
8.3 IR Functioning Chart
IR OUT A IR OUT B IR OUT C IR OUT D IR OUT E
IR IN 1 ◎◎◎◎ ▲
IR IN 2 ◎◎◎◎ ▲
IR IN 3 ◎◎◎◎ ▲
IR IN 4 ◎◎◎◎ ▲
IR IN 5 △ △ △ △ △ ▲
IR Sensor X
◎: IR in can select IR out
✕: Only accepts an IR signal from the remote control included in this
products package.
△: You do not have to select IR input as this device can receive IR signals
from all IR remote controls with a frequency between 30KHz~50 KHz
▲: You do not have to select input IR as this device can send IR signals to
all sources With a frequency between 30KHz~50 KHz
5
9. Remote Control
1. Power: Press the button to turn on/
standby the unit.
2. IR input 1: Select for IR OUT A~D:
Press A, B, C or D to select the
desired IR out for sending a signal.
3. IR input 2: Select for IR OUT A~D:
Press A, B, C or D to select the
desired IR out for sending a signal.
4. IR input 3: Select for IR OUT A~D:
Press A, B, C or D to select the
desired IR out for sending a signal.
5. IR input 4: Select for IR OUT A~D:
Press A, B, C or D to select the
desired IR out for sending a signal.
POWER
CR-81-06F9
ABCD
INPUT
1
ABCD
INPUT
2
ABCD
INPUT
4
ABCD
INPUT
3
2
1
3
4
5
6
Autres manuels pour CMIR-44
1
Table des matières
Autres manuels Cypress Matériel informatique
Cypress
Cypress CY4541 EZ-PD CCG4 Evaluation Kit Manuel utilisateur
Cypress
Cypress CY14B101Q1 Manuel utilisateur
Cypress
Cypress FM33256B Manuel utilisateur
Cypress
Cypress EZ-PD CCG3 Manuel utilisateur
Cypress
Cypress CY14E102L Manuel utilisateur
Cypress
Cypress AutoStore STK17T88 Instructions d'installation et d'utilisation
Cypress
Cypress CY8CKIT-001 Manuel utilisateur
Cypress
Cypress MB9B160R Series Manuel utilisateur
Cypress
Cypress CY8CKIT-029 PSoC Manuel utilisateur
Cypress
Cypress CY62137FV30 Manuel utilisateur
Cypress
Cypress CY8CKIT-029 PSoC Manuel utilisateur
Cypress
Cypress CY8CKIT-036 Manuel utilisateur
Cypress
Cypress CY62146DV30 Manuel utilisateur
Cypress
Cypress CY8CKIT-025 Manuel utilisateur
Cypress
Cypress CYUSB3ACC-004A Manuel utilisateur
Cypress
Cypress 256K (32K x 8) CY62256 Manuel utilisateur
Cypress
Cypress DCT-7 Manuel utilisateur
Cypress
Cypress EZ-OTG CY7C67200 Manuel utilisateur
Cypress
Cypress 7C185-15 Manuel utilisateur
Cypress
Cypress PSoC DESIGNER ImageCraft M8C Manuel utilisateur
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
