CYP CP-255I Manuel utilisateur
Operation Manual
Operation Manual
CP-255I
Multi-Format to HDMI Scaler
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
VS1 25/11/11 First release
VR2 03/07/13 Input 1080i resolution @60/50
VR3 18/10/13 RS-232 Port
CONTENTS
1. Introduction..............................................1
2. Applications.............................................1
3. Package Contents .................................. 1
4. System Requirements.............................. 1
5. Features....................................................2
6. Operation Controls and Functions......... 3
6.1 Front Panel...........................................3
6.2 Rear Panel ...........................................4
6.3 Remote Control...................................5
6.4 OSD Menu............................................6
6.5 RS-232 Pin Assignment ........................7
6.6 RS-232 Setting Commands.................8
6.7 RS-232 Status Commands ................12
6.8 Resolution Supports...........................14
8. Specications ........................................ 16
9. Acronyms ...............................................17
1
1. INTRODUCTION
The Multi-Format to HDMI Scaler is designed to upscale digital/analog
video signals from Composite, S-Video, PC, Component (HD) and
HDMI input sources, to digital HDMI output of a wide range of HDTV
and PC resolutions including 1080p and WUXGA (1920 x 1200).
As well as upscaling video, the scaler box also converts digital/analog
audio signals to digital format, which can then be output either
through HDMI combined with the video signal or separately via the
discrete Coaxial S/PDIF output.
The Scaler has a comprehensive on-screen display (OSD) menu that
allows the user to select a variety of output resolutions and adjust
them for the best picture quality.
2. APPLICATIONS
• Upscale the video from standard denition sources or a PC/Laptop
to a HDMI equipped display.
3. PACKAGE CONTENTS
• Multi-Format to HDMI Scaler
• Remote Control
• 1×D-Sub 15-pin Cable
• 1×Composite Video Cable (3 RCA)
• 5 V/3 A DC Power Supply Adaptor
• Operation Manual
4. SYSTEM REQUIREMENTS
• INPUT: Composite, Component, S-Video or HDMI, or PC VGA video/
audio source.
• OUTPUT: HDMI equipped TV or monitor, optional Coaxial (S/PDIF)
equipped receiver/amplier.
2
5. FEATURES
• HDMI, HDCP 1.1 and DVI 1.0 compliant
• Scales any PC (VGA~WUXGA) or HD (480i~1080p) resolutions to from
another PC/HD resolutions
• Automatically detects the correct settings of the connected display
and outputs the corresponding resolution and refresh rate, when
the NATIVE output is selected
• Supports 50/60 Hz frame rate conversion
• Supports 3D motion video adaptive, 3D de-interlacing, and 3:2 / 2:2
pull-down detection and recovery
• Provides output picture adjustment on contrast, brightness, hue,
saturation, sharpness, RGB (color tone) level, and aspect ratio size
• Supports high resolution input/output:
PC: VGA, SVGA, XGA, SXGA, UXGA, WXGA, WSXGA, and WUXGA
HDTV: 480i, 576i, 480p, 576p, 720p, 1080i and 1080p
• Supports digital and analog audio input and digital output
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER CV SV COMP PC
MEN
UE
NTER
Digital Video Scaler Processor
-
+
HDMI
1 2 5 63 4
1
POWER Button and LED: Press the button power the unit on or off.
When the power is turned on, the LED will illuminate.
2
IR Window
3
Input Buttons and LEDs: Press the required button (CV/SV/COMP/
PC/HDMI) to select the desired input source. The LED will illuminate
to indicate the corresponding input is selected.
4
MENU Button: Press the MENU button to bring up OSD operation
menu (see section 6.3 OSD Operation for reference.)
5
Minus (-)/Plus (+) Buttons: A. On the rst level of OSD menu, use +
and − buttons to move up/down the menu to highlight the item
for selection. B. Once the desired option is selected, use + and −
buttons to toggle between setting values.
6
ENTER Button: In the OSD menu, use the ENTER button to conrm
the selection.
4
6.2 Rear Panel
HDMI OUT
AUX IN RS-232PC IN
HDMI IN
PC IN
R
Cr/Pr
L
Cb/Pb
CO-AX
Y
R
R
LCV
DC 5V
LSV
CO-AX OUT
1 2
3 6 8
4 5 7 9
1
HDMI OUT and COAX OUT: Connect the HDMI OUT port to an HDMI
display such as HDTV or monitor. Connect the COAXIAL OUT port
(TOSLINK) to an amplier for separate digital audio output.
2
HDMI IN and AUX IN: Connect the HDMI IN port to an HDMI source
device such as a DVD player or set-top box or connect to a DVI
source equipment such as a PC with an HDMI to DVI cable. Use
the AUX IN port to input the audio signal when the video signal
input through the HDMI IN port is an DVI source.
3
RS-232: Connect to a PC/Laptop or RS-232 control system to use
RS-232 commands to control the device.
4
PC IN and Audio IN: Connect the D-sub 15-pin port to a PC for
video signal conversion. Connect the 3.5mm phone jack port to
the PC for audio signal conversion.
5
YCbCr/YPbPr IN and L/R IN: Connect the YCbCr/YPbPr input ports
(3 RCA) to source equipment such as a DVD player or set-top box
for video signal conversion. Connect the L/R audio input ports to
source equipment for audio signal conversion.
6
COAX IN: The COAXIAL port provides the digital audio input
support, and can be assigned to any of the video inputs. Once
connected, it can be assigned in the OSD Menu under Audio
Source Selection by selecting between Coaxial (S/PDIF) or other
audio source (see section '6.4 OSD Menu' for reference).
7
S-Video IN and L/R IN: Connect the S-Video input port to
source equipment such as a DVD player or set-top box for vido
signal conversion. Connect the L/R audio input ports to source
equipment for audio signal conversion.
5
8
Composite Video IN and L/R IN: Connect the Composite Video
input port to source equipment such as a DVD player or Set-top
box for video signal conversion. Connect the L/R audio input ports
to source equipment for audio signal conversion.
9
DC 5V: Plug the 5 V DC power supply into the unit and connect the
adaptor to AC wall outlet.
6.3 Remote Control
1
POWER: Press the button once to power on
the unit. Press again to enter standby mode.
2
INPUT: Press the button repeatedly to toggle
through various input sources.
3
HD, PC, HDMI/DVI: Press the appropriate
button to directly select component video,
PC, or HDMI/DVI input.
4
VGA, SVGA, XGA, SXGA, UXGA or 480p,
720p, 1080i, 1080p: Press appropriate button
to directly select the preferred output
resolution. Other output resolutions that
are not covered by these buttons can be
selected from the OSD Menu.
5
MENU: Press the button to bring up the OSD
main menu page.
6
EXIT: Press the button to exit from a sub
menu or main menu.
7
Up, Down, Left, Right and OK: Press the Up/Down button to move
the highlight bar to your desired parameter during the OSD
operation. Press the Left/Right button to increase/decrease the
value of a selected parameter.Press the OK (ENTER) button to
conrm your selection.
8
AUTO ADJUST: Press the button to optimize the positioning of the
picture (picture centering) on the screen.
9
RESET: Press the button to reset the unit's rmware setting to the
factory default value.
2
4
6
9 8
7
5
1
3
Autres manuels pour CP-255I
2
Table des matières
Autres manuels CYP Convertisseur de média
CYP
CYP CM-397M Manuel utilisateur
CYP
CYP CP-293N Manuel utilisateur
CYP
CYP EL-7400V Manuel utilisateur
CYP
CYP CSC-109TX Manuel utilisateur
CYP
CYP CSC-103TXPL Manuel utilisateur
CYP
CYP CHDBT-1H7CPL Manuel utilisateur
CYP
CYP AU-11SA-4K22 Manuel utilisateur
CYP
CYP SY-P290 Manuel utilisateur
CYP
CYP CSC-104 Manuel utilisateur
CYP
CYP CLUX-SDI2DVIA Manuel utilisateur
CYP
CYP SY-4KS4K22 Manuel utilisateur
CYP
CYP CMDPH-1A Manuel utilisateur
CYP
CYP CPT-387HD Manuel utilisateur
CYP
CYP QU-8MS Manuel utilisateur
CYP
CYP CV-401D Manuel utilisateur
CYP
CYP AU-11DM Manuel utilisateur
CYP
CYP DCT-40 Manuel utilisateur
CYP
CYP AU-D3-192 Manuel utilisateur
CYP
CYP CLUX-1HLR Manuel utilisateur
CYP
CYP SY-P295 Manuel utilisateur
