CYP CMSI-46PL Manuel utilisateur
CMSI-46PL
4 by 6 Matrix
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2013 by Cypress Technology.
All Rights Reserved.
Version 1.0 October 2013
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE
VR0 25/03/14 Preliminary Release
VR1 07/07/14 RS-232 Description
CONTENTS
1. Introduction...............................................................1
2. Applications..............................................................1
3. Package Contents ...................................................1
4. System Requirements...............................................2
5. Features.....................................................................2
6. Operation Controls and Functions..........................3
6.1 Front Panel ...........................................................3
6.2 Rear Panel............................................................4
6.3 Side Panel ............................................................5
6.4 Remote Control...................................................5
6.5 IR Pin Assignment ................................................6
6.6 RS-232 Protocols ..................................................6
6.7 RS-232 & Telnet Commands...............................7
6.8 RS-232 UART Command Illustration Diagram.10
6.9 Telnet Control ....................................................11
6.10 Web GUI Control .............................................13
7. Connection Diagram .............................................15
8. Specications .........................................................16
9. Acronyms ................................................................17
1
1. INTRODUCTION
The 4 by 6 Matrix allows HDMI signal from any of its four sources to be
routed to any of its six outputs simultaneously. With a thoughtful design
for local and remote connections both required in system integration,
the model is engineered with 2 HDMI and 4 CAT5e/6/7 outputs, the
later ones carry major HDBaseT features including the transmission
of high denition audio and video, bidirectional IR, RS-232 and PoC
(Power over Cable) over 60 meters. The remote control, RS-232, Telnet
and IP Control, with all information including system status presented
on its LCM display.
2. APPLICATIONS
• HDMI system controls
• Video/TV wall display and control
• Security surveillance and control
• Commercial advertising, displaying and control
• Lecture room display and control
• Hyper market demonstration and control
3. PACKAGE CONTENTS
• 1 x 4 by 6 Matrix
• HDMI over CAT5e/6/7 Receivers (Optional)
• 1 x IR Extender
• 1 x IR Blaster
• 1 x L&R Rack Ears
• 1 x 24V/3.75A DC Power Supply
• 1 x Power Cord
• 1 x Remote Control (with battery)
• 1 x Operation Manual
2
4. SYSTEM REQUIREMENTS
• Input source equipment with HDMI connection cables
• Industry CAT5e/6/7 cable
• HDMI over CAT5e/6/7 Receivers with industrial CAT5e/6/7 cables
• Output displays or audio receiver equipments with HDMI
connection cables
5. FEATURES
• Supports resolutions VGA to WUXGA and 480i to 1080p dependent
upon the output display’s EDID settings
• Supports distances up to 70 meters through CAT6/7 cables and
60m for CAT5e
• Supports 3D signal display dependent upon the output display’s
EDID settings
• Supports bidirectional IR from input and output locations
• Supports external and internal EDID settings
• Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
Master Audio Transmission
• Supports PoC (Power over Cable) on compatible receiver only
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
CMSI-46PL
4X6 HDMI MATRIX
POWER LOCK MENU
OUT
B2
A1C3
D4IN
FE
1 2 3 4 5 6
1LCM: This monitor displays your setting information with each input
and output selection.
2IR: This IR window accepts the remote control signal of this device
only.
3Power Button & LED: Press this button to turn ON the device and the
orange LED will illuminate when the power is ON. When the LED
illuminate in red it is in standby mode.
4LCOK: Press this button to lock all the buttons on the panel and the
LED will illuminate. To unlock, just press it again.
5Menu: Press this button once to select EDID setting from
STD(internal) 1 or TV(external) 2 then press it again to conrm the
selection. Press this button every time to conrm the selection.
61~4/A~F & OUT/IN button: Press OUT/IN button rst to select the
output/input then press the number button to make the selection
accordingly. For example, output A~B wish to select input 1 and
C~E wish to select input 2. Press OUT →A→B→IN →1→Menu,
and then press Out →C→D→E→IN →2→Menu. If the menu
button is not pressed the selection will not be changed.
4
6.2 Rear Panel
SERVICE
RS-232
CONTROL
B CA E FD
DC 24V
1
2
3
4
GND
GND GND
IR OUT
IR IN
ALL
V+
V+
1
IR IN IR OUT
2
IR IN IR OUT
3
IR IN IR OUT
4
IR IN IR OUT
HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4
HDMI OUT CAT5e/6/7 OUT CAT5e/6/7 OUT
HDMI OUT CAT5e/6/7 OUT CAT5e/6/7 OUT
2 3 4 45 5 5 10 115 6
1
7
8
7
8
7
8
7
8 9
1RS-232: This slot is to connect with D-Sub 9-pin cable from the PC/
Laptop device for RS232 control.
Note: This RS-232 obtain routable function that is, from the Matrix it
can send commands to all Receivers or from Receiver sides it can
also send commands to control the Matrix. In order to allow the
Receivers to send command to control the Matrix, a null modern
cable/adaptor is required.
2CONTROL: This port is for Telnet and Web GUI control. Connect to
an active network system with RJ45 terminated cable (for details,
please refers to section 6.7 & 6.8).
3Service: This slot is to connect with mini USB B type cable for
rmware update only.
4HDMI OUT A/D: These slots are to connect with HD TV/display for
instant display.
5CAT5e/6/7 OUT B/C/E/F: These slots are to connect with HDMI over
CAT5e/6/7 Receiver for signal extension up to 60m.
6HDMI IN 1~4: These slots are to connect to input source equipment
such as DVD player or Set-Top-Box with HDMI cable or DVI to HDMI
converter cable for input signal sending.
7IR IN 1~4: These slots are to connect with IR Extender included in
the package for IR signal receiving. Ensure that remote being used
is within the direct line-of-sight of the IR Extender.
8IR OUT 1~4: These slots are to connect with IR Blaster included in
the package for IR signal sending. Place the IR Blaster in direct
lineof-sight of the IR Extender.
9ALL IR OUT: This slot is to connect with the IR Blaster for IR signal
received from Receiver sides and send to the source side. Place
the IR Blaster in direct line-of-sight of the IR Extender.
5
10 ALL IR IN: This slot is to connect with the IR Extender for IR signal
receiving and send out to Receiver sides. Ensure that remote being
used is within the direct line-of-sight of the IR Extender.
11 DC24V: This slot is to plug the power cord with adaptor included
in the package and then connect them with AC wall outlet for
power supply.
6.3 Side Panel
1
1Ventilator: These are fan ventilator area, DO NOT block these area
or cover it with any object.
6.4 Remote Control
1Power: Press this button to
switch ON the device or set it
to standby mode.
2IN: Input ports selection 1~4.
3OUT: Output ports selection
A~F.
H
8
1A
B
2
C
3
4D
5E
6F
7G
CR-110
IN OUT
3
2
1
6
6.5 IR Pin Assignment
3
1
3
1
2
2
Power
IR Blaster Signal
NC
IR Signal
Power
Grounding
IR Extender
IR Blaster
6.6 RS-232 Protocols
CMSI-46PL Remote Control Console
PIN Assignment PIN Assignment
1 NC 1 NC
2Tx 2Rx
3Rx 3Tx
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 19200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
Table des matières
Autres manuels CYP Commutateur matriciel
CYP
CYP CPLUS-V4H2HPIP Manuel utilisateur
CYP
CYP OR-44VWC Manuel utilisateur
CYP
CYP CMSI-4H4CV Manuel utilisateur
CYP
CYP SM-2X2-HDMI-LC Manuel utilisateur
CYP
CYP OR-44-4K22 Manuel utilisateur
CYP
CYP MOD-32 Manuel utilisateur
CYP
CYP PU-8H8HBTPL Manuel utilisateur
CYP
CYP CMPRO-4H4H Manuel utilisateur
CYP
CYP CMSI-8H8CV Manuel utilisateur
CYP
CYP OR-H44E Manuel utilisateur
CYP
CYP CMSI-88 Manuel utilisateur
CYP
CYP MOD-16 Manuel utilisateur
CYP
CYP CMPRO-UA8H8HS Manuel utilisateur
CYP
CYP OR-HD22S Manuel utilisateur
CYP
CYP OR-HD24S Manuel utilisateur
CYP
CYP PUV-44XPL-AVLC Manuel utilisateur
CYP
CYP OR-HD88HC Manuel utilisateur
CYP
CYP CMSI-48E Manuel utilisateur
CYP
CYP PRO-SDI44 Manuel utilisateur
CYP
CYP CMSI-8H8HC Manuel utilisateur
