CYP CPLUS-32FX Manuel utilisateur
CPLUS-32FX
4K UHD+3×2 HDMI and Fiber Matrix
Operation Manual
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2017 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
VS0 27/06/17 Preliminary release
VS1 26/12/17 Final technical review
CONTENTS
1. Introduction......................................................1
2. Applications.....................................................1
3. Package Contents ..........................................1
4. System Requirements......................................2
5. Features............................................................2
6. Operation Controls and Functions.................3
6.1 Front Panel ................................................. 3
6.2 Rear Panel.................................................. 4
6.3 Remote Control......................................... 4
6.4 IR Cable Pin Assignments ......................... 5
6.5 RS-232 Protocol.......................................... 5
6.6 RS-232 and Telnet Commands ................ 6
6.7 Telnet Control ............................................ 9
6.8 WebGUI Control ...................................... 10
7. Connection Diagram ....................................16
7.1 HDMI Switching........................................ 16
7.2 Fiber Extension ......................................... 17
8. Specications ................................................18
8.1 Technical Specications ........................ 18
8.2 Video Specications............................... 19
9. Acronyms .......................................................20
1
1. INTRODUCTION
This 3×2 HDMI and Fiber Matrix allows customer to route up to three
HDMI input signals (two 18Gbps HDMI and one 10.2Gbps HDMI over
optical ber) to any of two HDMI outputs (one 18Gbps HDMI and
one 10.2Gbps optical ber). The optical ber input and output both
support transmission distances up to 300 meters and use paired LC
connectors. This unit supports resolutions up to 4K@60Hz (4:4:4, 8-bit),
16-bit Deep Color up to 1080p@60Hz, HDR (High Dynamic Range),
HD audio formats and other features dened by the HDMI 2.0
specication. HDMI sources with bandwidth higher than 10.2Gbps are
automatically chroma and/or bit-depth subsampled for transmission
over the ber output. Six pre-dened internal EDIDs and two external
EDID selections are available for EDID management. The unit provides
intuitive front panel controls as well as RS-232, Telnet, WebGUI and IR
remote control options.
2. APPLICATIONS
• Entertainment Rooms & Home Theaters
• Showrooms & Demo Rooms
• Lecture Hall Presentations
• Public Commercial Displays
3. PACKAGE CONTENTS
• 1×3 by 2 HDMI and Fiber Matrix
• 1×Remote Control (CR-155)
• 1×IR Extender Cable
• 1×3.5mm to 9-pin D-sub Adapter
• 1×5V/2.6A DC Power Adaptor
• 1×Operation Manual
2
4. SYSTEM REQUIREMENTS
• HDMI source equipment such as media players, video game
consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors or audio
ampliers.
• The use of “Premium High Speed HDMI” cables is highly
recommended.
• Use of the optical ber input/output requires a second unit and
appropriate paired LC multi-mode ber in a crossover conguration.
5. FEATURES
• HDMI with 3D & 4K@60Hz with HDR support
• DVI 1.0 compliant with the use of an HDMI-DVI adaptor
• HDCP 2.2 and 1.x compliant
• Supports HD resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) &
4096×2160@60Hz (4:4:4, 8-bit)
• Supports 16-bit Deep Color up to 1080p@60Hz
• 2×HDMI (18Gbps) and 1×HDMI over ber (LC pair, 10.2Gbps) inputs
• 1×HDMI (18Gbps) and 1×HDMI over ber (LC pair, 10.2Gbps) outputs
• HDMI sources with bandwidth higher than 10.2Gbps are
automatically chroma and/or bit-depth subsampled for transmission
over the ber outputs
• Fiber transmission distances of up to 300m
• 3×2 matrix routing between all inputs and outputs
• Supports pass-through of audio formats: LPCM 2.0/5.1/7.1, Bitstream,
and HD Bitstream
• Comprehensive EDID management support including 6 pre-dened
internal EDIDs and 2 external EDIDs
• Supports control via front panel, WebGUI, Telnet, RS-232, and IR
remote
3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
SERVICE
3x2 4K UHD+
HDMI / Fiber Matrix
+
POWER 123
OUT A
123
OUT B
1 2 3 4 5 6
1SERVICE: This slot is reserved for rmware update use only.
2IR WINDOW: Accepts IR signals from the included IR remote for
control of this unit only.
3POWER LED: This LED will illuminate green to indicate the unit is on
and receiving power. When the unit is in stand-by mode the LED
will illuminate red.
4POWER BUTTON: Press this button to power the unit on or place it
into stand-by mode.
Note: Ethernet, IR and RS-232 remain active while the unit is in
stand-by mode.
5OUT A BUTTON & LEDs: Press this button to sequentially switch
through the 3 available inputs, and mute, for Output A. The LEDs
will illuminate to indicate the currently selected input for Output A.
When all 3 LEDs are blinking, the output is muted.
6OUT B BUTTON & LEDs: Press this button to sequentially switch
through the 3 available inputs, and mute, for Output B. The LEDs
will illuminate to indicate the currently selected input for Output B.
When all 3 LEDs are blinking, the output is muted.
4
6.2 Rear Panel
DC 5VIR INRS-232
CONTROL
FIBER A HDMI B
OUT
FIBER 3
HDMI 2HDMI 1
IN
1 2 3 4 5 6
1FIBER A & HDMI B OUT: Connect the HDMI output to HDMI TVs,
monitors or ampliers for digital video and audio output. DVI
displays are supported with the use of an HDMI to DVI adapter.
Connect the ber (paired LC) output to the ber input on a
second unit.
2HDMI 1~2 & FIBER 3 IN: Connect the HDMI inputs to HDMI source
equipment such as media players, game consoles or set-top
boxes. DVI sources are supported with the use of an HDMI to DVI
adapter. Connect the ber (paired LC) input to the ber output
from a second unit.
3CONTROL: Connect directly, or through a network switch, to your
PC/laptop to control the unit via Telnet/WebGUI.
4RS-232: Connect, via the provided 9-pin adapter cable, to a PC,
laptop or other serial control device to send RS-232 commands to
control the unit.
5IR IN: Connect to the provided IR Extender to extend the IR control
range of the unit. Ensure that the remote being used is within direct
line-of-sight of the IR Extender.
6DC 5V: Plug the 5V DC power adapter into the unit and connect it
to an AC wall outlet for power.
6.3 Remote Control
1POWER: Press this button to power the unit on or
place it into stand-by mode.
2A1~A3 & B1~B3: Press any of these buttons to switch
immediately to the corresponding input for the
specied output (A or B).
Note: A4 & B4 have no function with this unit.
CR-155
POWER
1
2
3
4
1
2
3
4
BA
2
1
5
6.4 IR Cable Pin Assignments
3
1
2
IR Signal
Power
Ground
IR Extender
6.5 RS-232 Protocol
UNIT
►
◄
REMOTE SYSTEM
Pin Denition Pin Denition
1 NC 1 NC
2TxD 2RxD
3RxD 3TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data Bits: 8
Parity Bits: None
Stop Bits: 1
Flow Control: None
Table des matières
Autres manuels CYP Commutateur matriciel
CYP
CYP CMPRO-U4H4CVE Manuel utilisateur
CYP
CYP HDBT PU-4H4HBTE-4K Manuel utilisateur
CYP
CYP CMSDI-1616S Manuel utilisateur
CYP
CYP CMSI-46PL Manuel utilisateur
CYP
CYP PUV-1082-4K22 Manuel utilisateur
CYP
CYP SM-2X4-HDMI-LC Manuel utilisateur
CYP
CYP CMPRO-UA8H8HS Manuel utilisateur
CYP
CYP CMPRO-U8H8CVPL Manuel utilisateur
CYP
CYP PU-8H8HBTPL-4K22 Manuel utilisateur
CYP
CYP CMLUX-44E Manuel utilisateur
CYP
CYP OR-HD88HC Manuel utilisateur
CYP
CYP CMSI-8D8DS Manuel utilisateur
CYP
CYP PU-O4H4C Manuel utilisateur
CYP
CYP Elpro Video Labs CDPS-UC4H4HFS Manuel utilisateur
CYP
CYP OR-HD22S Manuel utilisateur
CYP
CYP CPLUS-1082CVAL Manuel utilisateur
CYP
CYP PU-8H8HBTPL-4K Manuel utilisateur
CYP
CYP PU-424HBTL-KIT Manuel utilisateur
CYP
CYP OR-HD88HC Manuel utilisateur
CYP
CYP OR-44U-4K22 Manuel utilisateur
