Crestron TSS-752-MSMK Manuel utilisateur

Crestron TSS-752-MSMK

Multi-Surface Mount Kit for TSS-752

Installation Guide

The specific patents that cover Crestron products are listed at patents.crestron.com.

Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.

Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or

their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or

photography.

This document was written by the Technical Publications department at Crestron.

Crestron TSS-752-MSMK Multi-Surface Mount Kit for TSS-752

Installation Guide – DOC. 7603B Contents •i

Contents

Multi-Surface Mount Kit for TSS-752: TSS-752-MSMK 1

Introduction ............................................................................................................................... 1

Setup .......................................................................................................................................... 2

Supplied Hardware ......................................................................................................2

Installation ................................................................................................................... 6

Resources................................................................................................................................. 13

Further Inquiries ........................................................................................................ 13

Future Updates .......................................................................................................... 13

Return and Warranty Policies .................................................................................................. 14

Merchandise Returns / Repair Service ...................................................................... 14

Crestron Limited Warranty........................................................................................ 14

Crestron TSS-752-MSMK Multi-Surface Mount Kit for TSS-752

Installation Guide – DOC. 7603B Multi-Surface Mount Kit for TSS-752: TSS-752-MSMK •1

Multi-Surface Mount Kit for

TSS-752: TSS-752-MSMK

Introduction

The Crestron®TSS-752-MSMK Multi-Surface Mount Kit provides a very versatile

surface mounting solution for a TSS-752 Room Scheduling Touch Screen. Using the

TSS-752-MSMK, the touch screen device can be mounted directly onto glass,

granite, marble, plaster, smooth stone and masonry, or virtually any other flat surface

using either the self-adhering mounting plate or screws.

An adhesive backed raceway is also provided for use on smooth surfaces to conceal

wires running to the touch screen from the floor or ceiling. The raceway is paintable

and is composed of three 3 foot (0.91 meter) sections plus an assortment of elbows

and couplings.

Models

DESCRIPTION MODEL NUMBER COLOR

Multi-Surface Mount Kit

TSS-752-MSMK-B-S

Black Smooth

TSS-752-MSMK-W-S

White Smooth

For simplicity within this guide the color and texture designation are omitted and the

term “TSS-752-MSMK” is used except where noted.

Multi-Surface Mount Kit for TSS-752 Crestron TSS-752-MSMK

2•Multi-Surface Mount Kit for TSS-752: TSS-752-MSMK Installation Guide – DOC. 7603B

Setup

Supplied Hardware

The TSS-752-MSMK consists of a metal mounting plate with adhesive backing,

plastic racer mount, raceway and appropriate nuts for mounting.

The multi-surface mounting option provides the necessary support and accessories

for post-construction applications. The table below lists all parts included with the

TSS-752-MSMK.

Supplied Hardware for the TSS-752-MSMK

DESCRIPTION PART NUMBER COLOR QUANTITY

Assembly, Metal, Plate, Glass

Mount, Foam with Adhesive

4519682 White 1

4519718 Black 1

Plastic, Racer Mount 4520154 White 1

4520155 Black 1

Metal, Bracket, On-wall Mount 2037960 - 2

Plastic, Wire Raceway Kit,

Paintable

2024932 White 1

Screw, 04-20 x 3/8”, Pan, Phil 2007137 - 4

Screw, 04-40 x 1/4”, Flat, Torx 2025312 Steel 2

2039651 Black 2

Nut, #04-40, External, Hex 2004878 - 4

Label, Custom, Polycarbonate 4519867 White 1

4519868 Black 1

Bit, Torx, T8, Tamper Proof,

Security

2025915 - 1

Crestron TSS-752-MSMK Multi-Surface Mount Kit for TSS-752

Installation Guide – DOC. 7603B Multi-Surface Mount Kit for TSS-752: TSS-752-MSMK •3

The dimensions of the TSS-752-MSMK are shown below and on the following

pages.

Glass Mounting Plate Overall Dimensions (Front and Side Views)

0.05 in

(2 mm)

0.09 in

(3 mm)

0.30 in

(8 mm)

3.29 in

(84 mm)

1.67 in

(43 mm)

Glass Mounting Plate Overall Dimensions (Rear View)

4.65 in

(119 mm)

4.45 in

(113 mm)

2.44 in

(62 mm)

2.24 in

(57 mm)

Multi-Surface Mount Kit for TSS-752 Crestron TSS-752-MSMK

4•Multi-Surface Mount Kit for TSS-752: TSS-752-MSMK Installation Guide – DOC. 7603B

Glass Mounting Plate with Plastic Racer Mount Overall Dimensions (Front and Side Views)

5.25 in

(134 mm)

2.50 in

(64 mm)

0.93 in

(24 mm)

0.66 in

(17 mm)

0.09 in

(3 mm)

Glass Mounting Plate with Plastic Racer Mount (Rear View)

Crestron TSS-752-MSMK Multi-Surface Mount Kit for TSS-752

Installation Guide – DOC. 7603B Multi-Surface Mount Kit for TSS-752: TSS-752-MSMK •5

Plastic Racer Mount Overall Dimensions (Front and Side Views)

0.84 in

(22 mm)

0.57 in

(15 mm)

0.76 in

(19 mm)

1.67 in

(43 mm)

2.50 in

(64 mm)

1.51 in

(39 mm)

5.25 in

(134 mm)

3.29 in

(84 mm)

Plastic Racer Mount Overall Dimensions (Rear View)

4.67 in

(119 mm)

2.45 in

(62 mm)

Multi-Surface Mount Kit for TSS-752 Crestron TSS-752-MSMK

6•Multi-Surface Mount Kit for TSS-752: TSS-752-MSMK Installation Guide – DOC. 7603B

Installation

This section provides an installation procedure for each mounting scenario. “Glass

Mounting” starts below, “Drywall, Paneling, Concrete or Brick Mounting” starts on

page 9 and “Raceway Mounting” is on page 12. Be sure to review each procedure

before starting.

Glass Mounting

The touch screen can be mounted onto a flat pane of glass or similar smooth surface

(such as granite, marble, plaster, smooth stone or masonry) using the included glass

mounting plate. The back of the plate has an adhesive tape that permanently attaches

to the glass. After installation is complete, the raceway kit may be installed on a

smooth surface by following the “Raceway Mounting” procedure on page 12.

NOTE: Ensure the glass mounting surface is cleaned with a glass cleaning product

that does not leave a film and is free of debris before mounting. Once glass mounting

plate has been attached, it cannot be easily removed.

Complete the following procedure to attach the glass mounting plate. The only tools

and supplies required and not supplied are a level, tape, flathead screwdriver, #2

Phillips screwdriver, 1/4” hex driver, and a glass cleaning product that does not leave

a film.

1. Thoroughly clean and dry the glass mounting surface using a glass cleaning

product that does not leave a film.

2. Using the level, carefully tape a horizontal reference line that coincides with

the lower edge of the mounting bracket.

CAUTION: Adhesive on glass mounting plate is a high strength bond.

Once adhesive meets a surface, it cannot be easily removed or adjusted.

3. Remove the adhesive backing from the glass mounting plate.

4. Holding the glass mounting plate (4519682 or 4519718) at a 45 degree

angle to the glass, carefully align the lower edge of the mounting plate with

the level taped line. Do not allow adhesive backing to come in contact with

the glass.

5. Once aligned with the level reference line, carefully tilt the glass mounting

plate back until it is secured to the glass. Firmly press glass mounting plate

to the glass to ensure proper adhesion and that any trapped air bubbles are

removed.

6. Using a flathead screwdriver, carefully break away one of the C-shaped

knockouts on the top, bottom or sides of the plastic racer mount (4520154

or 4520155). For example, if the LAN cable is to enter the plastic racer

mount from the bottom, break away the C-shaped knockout on the bottom

of the plastic racer mount.

7. Run the network wiring through the hole created by removing the knockout

in step #6.

8. Attach the plastic racer mount to the glass mounting plate using the 1/4”

hex driver and the four included #04-40 hex nuts (2004878). Refer to the

following illustration.

Table des matières

Autres manuels Crestron Support et étagère

Crestron

Crestron C2N-RMAK Manuel utilisateur

Crestron

Crestron PMK-4L Manuel utilisateur

Crestron

Crestron RMK-6L Manuel utilisateur

Crestron

Crestron HBK-6000 Manuel utilisateur

Crestron

Crestron TSW-730-MSMK Manuel utilisateur

Crestron

Crestron BB-1000L Manuel utilisateur

Crestron

Crestron CNXRMAK Manuel utilisateur

Crestron

Crestron CPC-CMT Comment utiliser

Crestron

Crestron CCS-UC-200-WSTND Manuel utilisateur

Crestron

Crestron MMK-3000L Manuel utilisateur

Crestron

Crestron TSW-750 Manuel utilisateur

Crestron

Crestron Mud Ring Mount Kit for Cameo 2 MMK-CBF-T Manuel utilisateur

Crestron

Crestron TSW-1070-RMB-4 Manuel utilisateur

Crestron

Crestron CPC-LMT Comment utiliser

Crestron

Crestron MMK-2000L Manuel utilisateur

Crestron

Crestron CNWMBG2-34A Manuel utilisateur

Crestron

Crestron TSW-550-TTK Manuel utilisateur

Crestron

Crestron FTI-PWR-D Comment utiliser

Crestron

Crestron RMK-8L Manuel utilisateur

Crestron

Crestron UCA-SMK-UC2 Manuel utilisateur

Crestron

Crestron TST-902-DSW Dessin dimensionnel

Crestron

Crestron CAEN-CK Manuel utilisateur

Crestron

Crestron HBK-3000 Manuel utilisateur

Crestron

Crestron Pre-Construction Wall Mount Back Box... Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur