Cornelius FCB Cord Kit Manuel utilisateur

FCB Cord Kit for V-Series 4 Flavor Installation Instructions

INSTALLATION INSTRUCTIONS

FCB CORD KIT FOR V-SERIES 4 FLAVOR

The following instructions should be used for installation of a power cord for a V-Series 4 Flavor unit.

Each kit will supply power to 1 unit.

Parts List

Tools Required

Phillips Screwdriver

Flat Screwdriver

Pliers

CAUTION – Only trained and certified electrical technicians should service this unit. ALL WIRING

MUST CONFORM TO NATIONAL AND LOCAL CODES.

DANGER – To avoid possible serious injury or death the ELCB (earth leakage circuit breaker) must

be installed in the electrical circuit of all units.

WARNING – To avoid possible electrical shock make sure the unit is properly grounded by con-

necting the earth ground cable, in the power cord to any connection in the machine marked with a

ground symbol.

CAUTION – The wiring must be properly grounded and connected through a disconnect switch

(slow-blow fuse or equivalent HVAC/R circuit breaker).

Electrical Requirements

Refer to the nameplate to determine the power requirements before connecting electrical power to the

unit. Voltage across contactor terminals L1 and L2, with the compressor running, must be within voltage

limits described in Table 1.

If the line voltage does not meet these requirements see the possible corrective actions in Table 2.

Item

Number Description Qty

150 Amp Power Cord 1

2Strain Relief 2

Table 1

Unit Requirements

V-Series 4 Flavor Integral Condense 208-230V, 60Hz, 50 Amp

V-Series 4 Flavor Water Condense 208-230V, 60Hz, 50 Amp

Table 2

Voltage Corrective Action

Below 180 VAC Do Not Connect Unit

180-190 VAC Boost voltage by +32 V

191-207 VAC Boost voltage by +16 V

208-230 VAC Use line voltage

231-246 VAC Reduce voltage by –16 V

247-262 VAC Reduce voltage by –32 V

Above 262 VAC Do Not Connect Unit

Revision Date: March 24, 2014 www.cornelius.com Revision: B

FCB Cord Kit for V-Series 4 Flavor Installation Instructions

Installation Steps

1. Switch the power to the unit off or remove the fuse to the electrical power circuit breaker.

2. Remove the back panel and the right side panel to gain access to the electrical area in the back of

the unit.

3. Remove the cover of the contactor box.

4. On both strain relief parts, loosen the screws until no threads show through the bottom.

5. Install the first strain relief to the bottom of the unit.

6. Install the second strain relief to the side of the con-

tactor box.

7. Feed the power cord through the first strain relief,

lead end first, from the outside of the unit to the

inside of the unit.

8. Pull the power cord to the second strain relief.

FCB Cord Kit for V-Series 4 Flavor Installation Instructions

9. Feed the power cord through the second strain

relief from the side into the contactor box.

10. Attach the two outside leads from the power cord to

the right side of the compressor contactor.

11. Remove the top ground nut from the ground stud.

Slip the ring of the middle ground lead over the

ground stud and secure it by tightening the ground

nut.

12. Pull the slack out of the power cord through the side

of the contactor box and tighten the strain relief on

the contactor box.

13. Pull the slack out of the power cord through the

back of the unit and tighten the strain relief on the

outside of the unit.

14. Replace the cover to the contactor box.

15. Replace the back panel and left side panel.

Table des matières

Autres manuels Cornelius Distributeur de boissons

Cornelius

Cornelius The Profile PR150 BC Manuel utilisateur

Cornelius

Cornelius DF/ED250PRO Manuel utilisateur

Cornelius

Cornelius TRIAD-150 Manuel utilisateur

Cornelius

Cornelius R-404A REFRIGERANT Manuel utilisateur

Cornelius

Cornelius ED Series Guide d'installation

Cornelius

Cornelius ED-250 Manuel utilisateur

Cornelius

Cornelius A8661 Guide de configuration

Cornelius

Cornelius JETSPRAY Guide de configuration

Cornelius

Cornelius Enduro ED-250 BCP Manuel utilisateur

Cornelius

Cornelius Jetspray JT20 Guide de configuration

Cornelius

Cornelius ED-300 Guide de configuration

Cornelius

Cornelius IDC Pro Mode d’emploi

Cornelius

Cornelius Liquid Base Beverage Dispenser Manuel du propriétaire

Cornelius

Cornelius remcor DB275--BCP Manuel utilisateur

Cornelius

Cornelius 326142000 Manuel utilisateur

Cornelius

Cornelius TRIAD-150 Manuel utilisateur

Cornelius

Cornelius ED 300 BC Manuel utilisateur

Cornelius

Cornelius FCB - 2 Flavor Manuel utilisateur

Cornelius

Cornelius ED 300 BC Manuel utilisateur

Cornelius

Cornelius Quantum 45200001 Guide de configuration

Cornelius

Cornelius Profile 150 Manuel utilisateur

Cornelius

Cornelius Quantum 45200003 Manuel utilisateur

Cornelius

Cornelius V4 Mode d'emploi

Cornelius

Cornelius Enduro 150 8 Valve Manuel utilisateur

Manuels Distributeur de boissons populaires d'autres marques

PEGAS

PEGAS Evolution Manuel utilisateur

Ugolini

Ugolini MT micro Manuel utilisateur

Bunn

Bunn SLCA-7 Instructions d'installation

Gekkeikan

Gekkeikan Sake Machine Manuel utilisateur

Olympia

Olympia DH709 Manuel utilisateur

Marco

Marco ECOSMART PB10 Manuel utilisateur

Marvel

Marvel ML24BN Series Manuel

Cecilware

Cecilware 2K-GB-LD Manuel

Sure Vend

Sure Vend 673 Manuel utilisateur

Nostalgia Electrics

Nostalgia Electrics KEG7000SS Manuel utilisateur

Bunn

Bunn LCR-3 HV Guide de dépannage

Servend

Servend SV-200 Manuel utilisateur

EdgeStar

EdgeStar VBR440 Manuel utilisateur

CDS AUTOMATEN

CDS AUTOMATEN ML-16C2-C Manuel utilisateur

Siemens

Siemens GA 3000 Manuel d'instructions et de sécurité

Selbach

Selbach Fruit Juice dispenser Manuel utilisateur

Taylor

Taylor C302NP Manuel utilisateur

Vinotemp

Vinotemp VT-WINEDISP2 Manuel utilisateur