Clevertronics ECFLED-LI Instructions d'installation et d'utilisation

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least 24 hours. Conduct

the following tests:

•For the first test, the emergency lamp must remain illuminated for at least 2 hours after disconnection from the mains

supply.

•Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are required to be

recorded in a service logbook, which is to be kept on-site at all times. If the unit fails to remain illuminated for the

requisite time, remedial action must be taken to repair the situation and once completed, the unit must pass a

subsequent test. For more specific information, please refer to the current edition of the AS 2293.3 Standard.

Trouble Shooting:

Below are a list of common problems and their possible causes.

Fault: The Green LED Test Switch indicator is not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in emergency mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode, but only stays on for a short period.

Check: Battery has been allowed to charge for at least 24 hours.

Battery for damage.

Fault: Green LED flashes once every 5 seconds-Battery is disconnected

Check: Battery is connected.

Fault: Green LED blinks off once every 5 seconds- Charging very flat battery

Allow 20min to recover battery then recheck

Fault: Green LED flashes at 2Hz (Fast flash)- Faulty battery

Replace battery

Rated Emergency Lumen Output in accordance with AS2293.1 (refer to

spacing tables for installation positions):

Refer to the Technical Label for classification information.

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during construction. As a

result, any Exit & Emergency Units, on these circuits, will have their batteries discharged or “cycled”. The Lithium battery

in this fitting has been selected to give excellent long life performance in a controlled AS2293 testing environment.

Excessive battery cycling will reduce through-life performance and may lead to premature battery failure. Battery warranty

claims, as a result of such abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz/

Victoria (Head Office & Manufacturing)

195 Chesterville Rd

Moorabbin VIC 3189

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

News South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9248 3720

Fax: +61 8 9248 3725

ECFLED-LI

Installation & Maintenance Instruction Leaflet

Designed in Australia to comply with the requirements

of the AS/NZS2293.3:2005

Models:

ECFLED-LI Economy Lithium Cleverfit LED Exit

Spare Parts:

1550195 –EcoLi,3.2V 600mAh 210mm lead,noBRKT

8002900 –PCA: LED Strip ECFLED-LI CT10242-D1

8002880 –PCA: Driver ECOLITH Cleverfit CT10240-L4

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before

installation, ensure that the electricity supply has been switched off and isolated. Installation must be

carried out in accordance with the relevant Australian and International Standards.

1942250 V1.1 March 2019

Images and Dimensions

Installation:

The Economy Lithium Cleverfit LED Exit (ECFLED-LI) can be installed either Ceiling or Wall Mounted and

can be mounted perpendicular to a wall using the (optional) Cleverfit Cantilever Bracket. The ECFLED uses

a “slide connect bracket base” that is mounted and wired into position first. The main body can be installed

once the base is wired or later to avoid damage during the construction phase. Please follow the steps

below to install the Cleverfit Exit:

•Disengage the slide connect bracket from the exit body. Position the base in the mounting position.

•Using the bracket as a guide, mark 2 holes for mounting and one for mains access. Then install the

bracket using appropriate fixings (not supplied).

•Connect the 240VAC supply to the mounting bracket.

•Configure allthe mounting parts and cable entry points as below (if required) and engage the body into

the slide connect bracket. Apply mains power and check that the Cleverfit Exit is operational.

Cleverfit Maintenance:

Lamp Replacement:

•Use only the lamp(s) recommended on the label inside the Cleverfit.

•To replace the lamp bar, remove the self-tapping screws, disconnect the signal cable and install

the new lamp bar.

•

*Please note that the 50,000 hour LED Lamp Bar used in the Cleverfit Exit does not suffer from burn

out. Lamp replacement can be done as scheduled maintenance, at >5 year intervals. Please make a

note, in the site logbook, as to when lamps should be changed.

Battery Replacement:

•Use only the battery recommended on the label inside the Cleverfit and on this instruction.

•Remove the screw securing the fitting to the mounting bracket.

•Remove the fitting from the bracket by sliding it forward.

•The battery is located in the top of the fitting. See images.

•Remove the clip holding the battery.

•Unplug the battery from the PCA and remove it.

•Insert the new battery into the holder, route the DC cable to the PCA and plug the new battery

into the connector.

•Secure the battery using clip.

Changing Exit Legend Inserts:

The Cleverfit Exit uses Clevertronics patented “Tamper proof” Exit legend cover and comes

complete with spare legend inserts to enable straight on, left or right arrow as well as SS/DS

combinations.

To change an Exit legend insert first remove the diffuser. The clear tamper proof cover is held in

place by 3 locking tabs in the top inside area of the diffuser. Use a tool to disengage and push

the locking tabs through to release the cover and remove the insert, replacing it with the desired

one. When double sided is required remove the cardboard insert from the second side when

adding decal.

To re-install the clear cover, first engage the 3 small lugs on the bottom of the cover into their

respective recesses in the diffuser. Once sure the lugs are located, and then the 2 side lugs,

carefully push the 3 locking tabs back in, to complete the process.

Cable Entry Point –Top of

bracket for ceiling mount,

20mm diameter, located in

centre of bracket.

Mounting Bracket - front view

Wall Mount screw

fixing point

Wall Mount screw

fixing point

Cable Entry Point –Rear of bracket for wall mount, 20mm

diameter, located in centre of bracket. Note: Bracket shown

from front with the terminal block cover removed.

Mounting Bracket –top view

Cable Entry Point –Rear of bracket for wall mount, 20mm

diameter, located in centre of bracket Note: Bracket only

shown from front with the terminal block cover removed.

Ceiling mount -

screw fixing points.

(Same other side)

250

Battery PCA

Fitting Top View

Autres manuels Clevertronics Équipement d'éclairage

Clevertronics

Clevertronics LP CFLLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP CBS2LEDS-DIF Series Caractéristiques techniques

Clevertronics

Clevertronics ECFLED-LI-TH Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT PRO LLIFE PRO Series Manuel utilisateur

Clevertronics

Clevertronics TS Trade Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics CLP CCIRC Series Manuel

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LJWELED-40 Series Manuel utilisateur

Clevertronics

Clevertronics EL EUBPRO-SM-LI Instructions d'installation et d'utilisation

Clevertronics

Clevertronics Nifty Lifelight Surface Mount Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LJELED-40 Series Manuel utilisateur

Clevertronics

Clevertronics L10 Weatherproof Jumbo LED Exit Instructions d'installation et d'utilisation

Clevertronics

Clevertronics ARGO-1200 EM Series Caractéristiques techniques

Clevertronics

Clevertronics LIFELIGHT-2PRO-SMS-600 Instructions d'installation et d'utilisation

Clevertronics

Clevertronics Trade TS CIRCLITE ECLLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE-SM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics FVP2LED-P Series Guide de maintenance et de service

Clevertronics

Clevertronics CleverEVAC L10 UltraBlade Pro Dynamic Red Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Caractéristiques techniques

Clevertronics

Clevertronics CLP Ultrablade Pro CUBPRO Series Manuel

Clevertronics

Clevertronics CLP CWSQLED Series Manuel

Clevertronics

Clevertronics LP CUBPRO Series Manuel utilisateur

Clevertronics

Clevertronics Trade Series Instructions d'installation et d'utilisation

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur