Clevertronics EL EUBPRO-SM-LI Instructions d'installation et d'utilisation

Models:

EUBPRO-SM-LI Economy Ultrablade Pro Surface Mount LED Exit

Spare Parts:

1560200 –Battery, 3.2 Volt 1.1Ah Li-ion

8002179 –PCA:EUBPRO LED Strip Assy (CT10602-x)

8002983 - PCA: EUBPRO-SM #CT10614-L2

Important:

It is illegal for anyone, except for a licensed electrician to install or maintain this product. Before installation,

ensure that the electricity supply has been switched off and isolated. Installation must be carried out in

accordance with the relevant Australian and International Standards.

1943057 V1.0 September 2018

Designed in Australia to comply with the requirements

of AS2293.3:2005 and AS/NZ CISPR:15

Victoria (Head Office & Manufacturing)

195 Chesterville Rd

Moorabbin VIC 3189

Phone: +61 3 9559 2700

Fax: +61 3 9559 2799

New South Wales

Phone: +61 2 8805 6400

Fax: +61 2 8805 6444

Queensland

Phone: +61 7 3442 9700

Fax: +61 7 3442 9777

South Australia/Northern Territory

Phone: +61 8 8301 8800

Fax: +61 8 8351 8286

Western Australia

Phone: +61 8 9248 3720

Fax: +61 8 9248 3725

New Zealand

Phone: +64 800 548 448

Economy Ultrablade Pro Surface Mount LED Exit

Installation & Maintenance Instruction Leaflet

Testing:

Once connected to the 240V mains supply, the unit must be allowed to charge the battery for at least

24 hours. Conduct the following tests:

For the first test, the emergency lamp must remain illuminated for at least 2 hours after

disconnection from the mains supply.

Subsequent tests require the unit to illuminate for at least 90 minutes. The results of all tests are

required to be recorded in a service logbook, which is to be kept on-site at all times. If the unit

fails to remain illuminated for the requisite time, remedial action must be taken to repair the

situation and once completed, the unit must pass a subsequent test. For more specific

information, please refer to the current edition of the AS 2293.3 Standard.

Ultrablade Maintenance:

LED Lamp Replacement:

Use only the LED Strip recommended in

the Spares Parts list of this instruction.

Disconnect battery from LED driver.

Remove the screw holding the driver PCA.

Remove the PCA.

Remove the 4 screws holding the battery

bracket. Remove the bracket with the

battery.

Disconnect the signal cable from LED strip.

Remove 4 self-tapping screws and unclip

the LED strip.

Install the new LED strip following the

above procedure in reverse.

Battery Replacement:

Use only the battery recommended in the

Spares List on this instruction.

Remove the battery from battery

compartment, un-plug the lead from the

battery connector remove the old battery.

Plug the new battery into the battery

connector.

Secure the battery into the battery

compartment

Trouble Shooting:

Below are a list of common problems and their possible

causes.

Fault: The Green LED Test Switch indicator is

not illuminated.

Check: A.C. is connected and is turned on.

Battery is connected

Test Switch for damage.

Fault: Lamp does not illuminate in emergency

mode.

Check: A.C. is connected.

Lamp is correctly inserted.

Battery is connected

Fault: Lamp illuminates in emergency mode,

but only stays on for a short period.

Check: Battery has been allowed to charge for at

least 24 hours.

Battery for damage.

Fault: Green LED flashes once every 5

seconds-Battery is disconnected

Check: Battery is connected.

Fault: Green LED blinks off once every 5

seconds- Charging very flat battery

Allow 20min to recover battery then recheck

Fault: Green LED flashes at 2Hz (Fast flash)-

Faulty battery

Replace battery

Rated Emergency Lumen Output in accordance with AS2293.1 (refer to

spacing tables for installation positions), not Included –TH version:

C0=E6.3 (8m) C90=E6.3 (8m)

Caution:

On many building sites, power circuits may be cut off in an uncontrolled and repetitive basis during construction. As

a result, any Exit & Emergency Units, on these circuits, will have their batteries discharged or “cycled”. The battery

in this fitting has been selected to give excellent long-life performance in a controlled AS2293 testing environment.

Excessive battery cycling will reduce through-life performance and may lead to premature battery failure. Battery

warranty claims, as a result of such abuse, are specifically EXCLUDED from Clevertronics warranty terms.

Warranty:

For Product Warranty information and Terms and Conditions of Sales please refer to our website

http://clevertronics.com.au/terms-conditions-sale-australia-nz

Installation:

The EL Ultrablade Pro Surface Mount LED Exit (EUBPRO-SM-LI) is a surface mount fitting. The

EUBPRO-SM can be attached directly to any solid surface. Please follow the steps below to install the

EUBPRO Exit:

Open the fitting using the 2 screws on either side of the blade.

Locate the mounting surface.

Drill holes in the mounting base to suit the mounting method, Ceiling or Wall (see images below).

Use the mounting bracket to mark-out the mounting holes for Ceiling or Wall Mount.

Drill power access hole as required.

Mount the fitting using appropriate fixings.

Route the power to the mains connection and connect the 240VAC supply.

Attach the blade assembly to the bracket and tighten the 2 mounting screws.

Apply power to the fitting and test.

Pull the trim out at

the centre

Lift the decal and

slide out

Changing EXIT Legend Inserts:

The Ultrablade Pro Exit comes with an assortment of standard legends.

1. To remove the legend, grasp the centre of the bottom trim piece and pull down slightly to expose

the legend edge. See photo.

2. Grasp the bottom edge of the legend and slide the existing legend out of the blade, while working

the edges out along the sides.

3. Slide the new legend into the blade, ensuring to fit the edges into the sides then slide the legend to

the top of the blade. Insert one bottom corner then the other. Slide the legend down into the bottom

trim.

Ceiling Mounting Points (4)

Wall Mounting Points (2)

Insert corners (1&2)

then slide up (3)

Insert corners (4&5), then

slide down

Power Connections Power Access

Autres manuels Clevertronics Équipement d'éclairage

Clevertronics

Clevertronics L10 Argonaut PLUS Manuel utilisateur

Clevertronics

Clevertronics TS EUBPRO-LI Instructions d'installation et d'utilisation

Clevertronics

Clevertronics Glider Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP LIFELIGHT PRO CLIFE PRO-SMC Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics EJELED-40-LI Instructions d'installation et d'utilisation

Clevertronics

Clevertronics ARGO-1200 EM Series Caractéristiques techniques

Clevertronics

Clevertronics LP CBS2LEDS-DIF Series Caractéristiques techniques

Clevertronics

Clevertronics L10 LBLLED-REC-WM Series Caractéristiques techniques

Clevertronics

Clevertronics Trade Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP CCIRC Series Instructions d'utilisation et d'entretien

Clevertronics

Clevertronics L10 LLIFE-PRO-WP-IPREM Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LSBLED Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics CLP LIFELIGHT Pro Manuel utilisateur

Clevertronics

Clevertronics LP CWSQLED Series Manuel utilisateur

Clevertronics

Clevertronics LP LIFELIGHT CLIFE-RECSP Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 ARGOPRO-1200-L10POD Series Manuel utilisateur

Clevertronics

Clevertronics ECFLED-LI-TH Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics L10 LIFELIGHT PRO LWPLIFE-PRO-CM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics ARGOPRO-1200 Series Manuel utilisateur

Clevertronics

Clevertronics L10 LIFELIGHT LLIFE-SM Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics LP Cleverfit Pro CCFPRO TH Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics CBULKy Series Instructions d'installation et d'utilisation

Clevertronics

Clevertronics l10 LBULKy Series Instructions d'installation et d'utilisation

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur