Cisco WAP131 Manuel utilisateur

Reboot and Reset Factory Default Settings on

the WAP131

Objective

The factory default reset erases all configuration settings that have been modified by the

user, and restores the device to its original settings. This may be helpful if you lose the

password to a device and wish to regain access.

Performing a reboot restarts the device with a saved configuration.

The objective of this article is to show you how to reset to factory default settings and how to

reboot a WAP131 Wireless Access Point.

Note: It is advised to save a backup copy of the configuration before beginning this process.

Refer to Download and Backup Configuration Files on the WAP131 and WAP351 for

additional information.

Applicable Devices

• WAP131

Software Version

• 1.0.0.39

Reset to Factory Default

There are two ways to reset the Access Point to the factory default configuration:

• Hardware reset

• Reset with the use of the web configuration utility

Hardware Reset

Step 1. Press and hold the Reset button located at the back of the device for approximately

ten seconds with a pin.

The Access Point reloads and is set to the default configuration settings.

Step 2. Login with the default credentials. The default username is cisco, and the default

password is cisco.

Reset with the use of the Web Configuration Utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot. The

Reboot page opens:

Step 2. To reset the device, click the Reboot To Factory Default button.

A Confirm page appears:

Step 3. Click OK.

A Progress Bar appears:

Step 4. After the reboot is completed, login with the default credentials. The default

username is cisco, and the default password is cisco.

Rebooting the Device

There are two ways to reboot the Access Point:

• Hardware reboot

• Reboot with the use of the web configuration utility

Hardware Reboot

Step 1. Press the Power button to turn off the device. After 10 seconds have passed, press

the Power button a second time to power the device back on. The Access Point reboots and

is refreshed.

Note: The power button will not have any affect if the WAP is being powered with PoE

(Power over Ethernet).

Reboot with the use of the Web-based utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot. The

Reboot page opens:

Step 2. To reboot the device, click the Reboot button.

A Confirm page appears:

Step 3. Click OK to continue with reboot.

A Progress Bar appears:

Step 4. The Login page appears. Login with the saved administration credentials.

Autres manuels pour WAP131

3

Table des matières

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco WAP351 Mode d’emploi

Cisco

Cisco Aironet 1200 Series Manuel utilisateur

Cisco

Cisco 700 series Manuel utilisateur

Cisco

Cisco Aironet 1600 Series Guide de référence rapide

Cisco

Cisco 1830 Series Manuel utilisateur

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Mode d’emploi

Cisco

Cisco Aironet 2600 Series Manuel utilisateur

Cisco

Cisco aironet 2800 series Guide de référence rapide

Cisco

Cisco WAP4410N - Small Business Wireless-N Access... Manuel utilisateur

Cisco

Cisco WAP150 Manuel utilisateur

Cisco

Cisco Aironet 1300 Series Manuel

Cisco

Cisco WET200 Wireless-G Business Ethernet Bridge Manuel utilisateur

Cisco

Cisco Aironet 1700 Guide de référence rapide

Cisco

Cisco AIR-AP1572IC Manuel

Cisco

Cisco Wap581 Mode d’emploi

Cisco

Cisco Meraki Go GR10 Manuel utilisateur

Cisco

Cisco Aironet 1530 Manuel utilisateur

Cisco

Cisco AIR-LAP1310G Manuel utilisateur

Cisco

Cisco 1004-CH - 1004 Enet/ISDN/Bri Rter Guide de référence rapide

Cisco

Cisco AIR-AP1120B-A-K9 - Aironet 1100 Series Access... Manuel

Cisco

Cisco Aironet 1040 Series Manuel utilisateur

Cisco

Cisco Catalyst IW9165D Manuel

Cisco

Cisco ASR 1001 Manuel

Cisco

Cisco Aironet 1200 Series Manuel d'installation et d'exploitation

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur