Cisco Meraki GR60 Manuel utilisateur

The Cisco Meraki GR60 is a dual-band

enterprise class 802.11ac cloud-managed

access point

Package Contents

The GR60 package contains the following:

GR60 Cloud-Managed Access Point

Mount cradle including built-in level tool

Mount Kit

oWall screws and wall screw anchors

Understanding the GR60

Your Meraki GR60 has the following features:

The mount cradle has the following features:

Ethernet Ports

The GR60 features a Gigabit Ethernet RJ45 port that accepts 802.3at and 802.3af power

(labeled “Eth0, PoE”). This port should be used for uplink to your WAN connection.

Power Source Options

The GR60 access point can be powered using either the Meraki AC Adapter, PoE Injector

(both sold separately), or a third-party PoE switch.

Factory Reset Button

If the button is pressed and held for at least ﬁve seconds and then released, the GR60 will

reboot and be restored to its original factory settings by deleting all conﬁguration

information stored on the unit.

LED Indicators and Run Dark Mode

Your GR60 is equipped with a multi-color LED light on the front of the unit to convey

information about system functionality and performance:

Orange - AP is booting (permanent Orange suggests hardware issue)

Rainbow - AP is initializing/scanning

Blinking Blue - AP is upgrading

Green - AP in Gateway mode with no clients

Blue - AP in Gateway mode with clients

Blinking Orange - AP can't find uplink

The GR60 may be operated in “Run Dark” mode for additional security and to reduce the

visibility of the access point. In this mode, the LED will not be illuminated. This mode may be

enabled through Meraki dashboard.

Pre-Install Preparation

You should complete the following steps before going on-site to perform an installation.

Conﬁgure Your Network in Dashboard

The following is a brief overview only of the steps required to add an GR60 to your network.

For detailed instructions about creating, conﬁguring and managing Meraki wireless

networks, refer to the online documentation (documentation.meraki.com).

1. Login to http://dashboard.meraki.com. If this is your ﬁrst time, create a new account.

2. Find the network to which you plan to add your APs or create a new network.

3. Add your APs to your network. You will need your Meraki order number (found on

your invoice) or the serial number of each AP, which looks like Qxxx-xxxx-xxxx, and is

found on the bottom of the unit. You will also need your Enterprise license key,

which you should have received via email.

4. Go to the map / ﬂoor plan view and place each AP on the map by clicking and

dragging it to the location where you plan to mount it.

Check and Upgrade Firmware

To ensure your GR60 performs optimally immediately following installation, it is

recommended that you facilitate a ﬁrmware upgrade prior to mounting your GR60.

1. Attach your GR60 to power and a wired Internet connection. See the "Power the

GR60" section for details.

2. The GR60 will turn on and the LED will glow solid orange. If the unit does not require

a ﬁrmware upgrade, the LED will turn either green (no clients associated) or blue

(clients associated) within thirty seconds.

* If the unit requires an upgrade, the LED will begin blinking orange until the upgrade is

complete, at which point the LED will turn solid green or blue. You should allow at least a

few minutes for the ﬁrmware upgrade to complete, depending on the speed of your

internet connection.

Check and Conﬁgure Firewall Settings

If a ﬁrewall is in place, it must allow outgoing connections on particular ports to particular IP

addresses. The most current list of outbound ports and IP addresses for your particular

organization can be found here.

Assigning IP Addresses to GR60s

All gateway GR60s (GR60s with Ethernet connections to the LAN) must be assigned

routable IP addresses. These IP addresses can be dynamically assigned via DHCP or statically

assigned.

Dynamic Assignment

When using DHCP, the DHCP server should be conﬁgured to assign a static IP address for

each MAC address belonging to a Meraki AP. Other features of the wireless network, such as

802.1X authentication, may rely on the property that the APs have static IP addresses.

Static Assignment

Static IPs are assigned using the local web server on each AP. The following procedure

describes how to set the static IP:

1. Using a client machine (e.g., a laptop), connect to the AP wirelessly (by associating to

any SSID broadcast by the AP) or over a wired connection.

2. If using a wired connection, connect the client machine to the GR60 either through a

PoE switch or a PoE Injector. If using a PoE switch, plug an Ethernet cable into the

GR60’s Ethernet jack, and the other end into a PoE switch. Then connect the client

machine over Ethernet cable to the PoE switch. If using a PoE Injector, connect the

GR60 to the “PoE” port of the Injector, and the client machine to the “LAN” port.

3. Using a web browser on the client machine, access the AP’s built-in web server by

browsing to http://my.meraki.com. Alternatively, browse to http://10.128.128.128.

4. Click on the “Uplink Conﬁguration” tab. Log in. The default login is the serial number

(e.g. Qxxx-xxxx-xxxx), with no password (e.g., Q2DD-551C-ZYW3).

5. Conﬁgure the static IP address, net mask, gateway IP address and DNS servers that

this AP will use on its wired connection.

6. If necessary, reconnect the AP to the LAN.

Static IP via DHCP Reservations

Instead of associating to each Meraki AP individually to conﬁgure static IP addresses, an

administrator can assign static IP addresses on the upstream DHCP server. Through “DHCP

reservations,” IP addresses are “reserved” for the MAC addresses of the Meraki APs. Please

consult the documentation for the DHCP server to conﬁgure DHCP reservations.

Collect Tools

You will need the following tools to perform an installation:

Collect Additional Hardware for Installation

You will need the following hardware to perform an installation:

Installation Instructions

Choose Your Mounting Location

A good mounting location is important to getting the best performance out of your GR60

access point. Keep the following in mind:

1. The device should have unobstructed line of sight to most coverage areas. For

example, if installing in an ofﬁce ﬁlled with workspaces divided by mid-height cubicle

walls, installing on the ceiling or high on a wall would be ideal.

2. Power over Ethernet supports a maximum cable length of 300 ft (100 m).

3. If being used in a mesh deployment, the GR60 should have line of sight to at least

two other Meraki devices. A Cisco Partner can help ensure that your AP placement is

ideal.

Install the GR60

For most mounting scenarios, the GR60 mount cradle provides a quick, simple, and ﬂexible

means of mounting your device. The installation should be done in two steps. First, install

the mount cradle to your selected location. Then, attach the GR60 to the mount cradle

Mount the GR60

Attach the GR60 to the Mount Cradle

The GR60 attaches to the mount cradle with two tabs on the cradle that insert into the

GR60, and is secured to the cradle using one screw.

To attach the GR60 to the mount cradle properly, line up the top edge of the AP with the

top tab of the mount cradle. Since the cradle is already mounted to the wall, guide the GR60

towards the top tab and insert the top tab into the GR60’s slot.

Then adjust the GR60 to guide the GR60’s bottom slot into the cradle’s bottom tab until it

clicks into place. Once in place, the GR60 should be secured to the cradle by using one of the

included screws in the cradle’s bottom tab.

To release the GR60 from the mount cradle, first remove the security screw that secures the

GR60 to the cradle’s bottom tab. While holding the GR60 with one hand, press the cradle’s

bottom tab upwards, releasing the GR60 from the bottom of the cradle. Then remove the

GR60 from the cradle’s top tab.

Power the GR60

If mounting to an electrical junction box, feed the Ethernet cable through the cable access

hole in the mount cradle. If mounting to a wall or ceiling, the Ethernet cable will feed from

behind the GR60. The "Power Source Options" section of this document lists the different

powering options and their unique characteristics.

Verify Device Functionality and Test Network Coverage

1. Check LEDs

Table des matières

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco WAP2000 Mode d’emploi

Cisco

Cisco Aironet 1300 Series Manuel

Cisco

Cisco MERAKI MR72 Manuel utilisateur

Cisco

Cisco AIR-AP1010 - 1000 Series Lightweight Access... Manuel utilisateur

Cisco

Cisco Aironet 1572EC Guide de référence rapide

Cisco

Cisco 500 Series Manuel de l'opérateur

Cisco

Cisco Aironet 1815i Manuel utilisateur

Cisco

Cisco AIR-BR1310G-A-K9 - Aironet 1310 Outdoor Access... Manuel

Cisco

Cisco Aironet 1100 Series Manuel de l'opérateur

Cisco

Cisco Small Business WAP551 Manuel utilisateur

Cisco

Cisco WAP121 Manuel utilisateur

Cisco

Cisco Aironet 600 Series Manuel utilisateur

Cisco

Cisco Aironet 1250 Series Manuel utilisateur

Cisco

Cisco Aironet 1140 Series Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel

Cisco

Cisco 7200 VXR Series Manuel utilisateur

Cisco

Cisco Aironet 1570 Series Manuel utilisateur

Cisco

Cisco Aironet 1600 Series Manuel utilisateur

Cisco

Cisco AIR-AP1041N-A-K9 Manuel utilisateur

Cisco

Cisco WAP351 Mode d’emploi

Cisco

Cisco WAP571 Manuel utilisateur

Cisco

Cisco WAP371 Mode d’emploi

Cisco

Cisco WAP361 Manuel utilisateur

Cisco

Cisco Meraki MR53E Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur