Cisco 8201 Manuel utilisateur

Replace Chassis Components

•Replace Fan Modules for Cisco 8201 Routers, on page 1

•Replace Power Supply, on page 3

Replace Fan Modules for Cisco 8201 Routers

The fan module is designed to be removed and replaced while the system is operating without presenting an

electrical hazard or damage to the system. Please keep the replacement fan modules ready prior to attempting

this task.

The routers support FAN-1RU-PI (port-side intake airflow) and FAN-1RU-PE (port-side exhaust airflow)

fan modules.

Note

The airflow direction must be the same for all power supply and fan modules in the chassis.

Note

Step 1 To remove a fan module, follow these steps:

a) Press two latches on the fan module and grasp the handle of fan module.

Replace Chassis Components

Figure 1: Cisco 8201 Router —Remove Fans

Latched fan module1

b) As you simultaneously press the latches pull the fan module fully out of the chassis.

Step 2 To install a fan module, follow these steps:

a) Hold the fan module with the LED at the top.

b) Align the fan module to the open fan tray slot in the chassis, and press the module all the way into the slot until the

left and right latches click and are locked on the chassis.

Replace Chassis Components

Replace Fan Modules for Cisco 8201 Routers

If the fan module does not go all the way into the slot, do not force it. Remove the fan module and verify

that it is the correct type for your router and in the correct orientation. To verify the status of fans and the

speed, use the show environment fan command.

Note

c) If the chassis is powered on, listen for the sound of the fans in operation. You should immediately hear them in

operation. If you do not hear them, ensure that the fan module is inserted completely in the chassis.

During the fan module replacement, the other fans adjust their speed to allow for proper initialization of

the new module. When you insert a new fan module, the fans may run at lower or higher speeds for a few

minutes.

Note

d) Verify that the fan module LED is green. If the LED is not green, one or more fans are faulty. If this situation occurs,

contact your customer service representative for replacement parts.

Replace Power Supply

Use this procedure to replace the AC or DC power supply units. Be sure to power down the fixed configuration

PDU (power distribution unit) before removing it from the chassis.

Step 1 If the power supply is connected to a AC or DC circuit, shut off the circuit at the circuit breaker.

Step 2 Disconnect the PSU cable.

Step 3 Press the tab inward to unlatch the PSU, and pull the handle to remove the PSU.

Step 4 Insert the new PSU.

If the PSU does not go all the way into the slot, do not force it. Remove the PSU and verify that it is the correct

type for your router and in the correct orientation.

Note

Step 5 Connect the PSU cable.

Step 6 If the power supply is connected to a DC circuit, turn on the circuit breaker for the DC power source. After replacing the

PSU, verify the power using the show environment power command.

Replace Chassis Components

Replace Power Supply

Figure 2: Cisco 8201 Router —Remove Power Supply

Power supply1

Replace Chassis Components

Replace Power Supply

Table des matières

Autres manuels Cisco Routeur réseau

Cisco

Cisco Small Business Pro SRP527W Manuel utilisateur

Cisco

Cisco 7603 - Modular Expansion Base Manuel utilisateur

Cisco

Cisco ASR1002 - ASR 1002 Router Manuel utilisateur

Cisco

Cisco Nexus 9000 Series Manuel utilisateur

Cisco

Cisco 7301 Series Manuel utilisateur

Cisco

Cisco WS-SUP720-3B - Supervisor Engine 720 Manuel utilisateur

Cisco

Cisco IR809 Manuel utilisateur

Cisco

Cisco SB 106 Manuel utilisateur

Cisco

Cisco 805 Series Manuel utilisateur

Cisco

Cisco SFE2000P Manuel utilisateur

Cisco

Cisco 7200 Series Instructions originales

Cisco

Cisco 7507 Manuel utilisateur

Cisco

Cisco 1700 series Guide d'installation

Cisco

Cisco RV042 - Small Business Dual WAN VPN Router Instructions d'utilisation

Cisco

Cisco IR8340 Guide de démarrage rapide

Cisco

Cisco Linksys WET610N Manuel utilisateur

Cisco

Cisco ASR 900 Series Manuel utilisateur

Cisco

Cisco 2600 Series Manuel

Cisco

Cisco Cisco 888 Manuel

Cisco

Cisco ADSL Modem Router Manuel utilisateur

Cisco

Cisco 12010 series Manuel utilisateur

Cisco

Cisco NCS55A1 Manuel

Cisco

Cisco HiPort Manuel utilisateur

Cisco

Cisco 3825 Series Manuel de service

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur