Cisco ASR 9000 Series Manuel utilisateur

Cisco ASR 9000 Series Line Card Quick Reference Guide

Topics

The Cisco ASR 9000 Series Routers

meet the regulatory compliance

and safety approval requirements.

Note: Unless specied otherwise, the

images are for only representational

purposes.

For detailed safety information, see:

Regulatory Compliance and Safety

Information for the Cisco ASR 9000

Series Routers.

Safety Warnings

Failure to observe the safety

warnings may result in serious injury

to personnel or damage to the

hardware.

For hardware installation

documentation, see

Cisco ASR 9000 Series Aggregation

Services Router Hardware

Installation Guide

Cisco ASR 9000 Series Aggregation

Services Router Ethernet Line Card

Installation Guide

Cisco ASR 9000 Series Aggregation

Services Router Overview and

Reference Guide

1. Unpacking the Line Card

2. Installing the Line Card

3. Cable Management

4. Maintenance Best Practices

ALLOTHERBOARDS-THISSIDETOBOARD

SURESHOT-THISSIDETOBOARD

ALLOTHERBOARDS-THISSIDETOBOARD

SURESHOT-THISSIDETOBOARD

ALLOTHERBOARDS-THISSIDETOBOARD

SURESHOT-THISSIDETOBOARD

Plastic side rails

Line card

ALLOTHERBOARDS-THISSIDETOBOARD

SURESHOT-THISSIDETOBOARD

Plastic blocker

Wooden base

board

Foam cushion

Rolled Foam

Sealed line card

package placed

sideways

Foam cushion

Outer packaging

box

Unpacking the Line Card

Package Contents

.Foam Cushion

.Pink Antistatic Rolled Foam

.Sealed Line Card Package

For packaging guidelines, see Page 6

Caution!

.For convenience and safety purposes,

two persons should handle the line card.

.To avoid damage, place the line card

horizontally on a at antistatic surface.

The outer packaging box contains an

antistatic pink rolled foam that can be used

for this purpose.

.Wear ESD gloves to unwrap the ESD

bag, and remove the line card.

Cisco ASR 9000 Series

Line Card

Lift the inner packaging box that

contains the line card and place it

on a at surface.

Open the seal of the inner

packaging box.

Remove the line card from the

plastic side rails of the wooden

base board.

Unscrew the screws from the

plastic blocker that is on the

wooden base board.

Wear ESD gloves and unwrap the

ESD bag, which contains the line

card placed on a wooden base board.

Open the seal on the outer packaging

box. Remove the foam cushion.

1 2 3

Place the line card on an antistatic

surface while preparing the chassis

for card installation.

5 6

For future use, store the packaging

boxes.

Follow the directions provided on the plastic

blocker for its correct orientation while

reinserting the card on the wooden base

board.

To repack a line card to return it, perform the

steps in the reverse order.

98 Screw back the plastic blocker on

the wooden base board.

Installing the Line Card

Caution!

.For convenience and safety purposes,

two persons should handle the line card.

.Never carry the line card by holding it by

the ejector levers or put pressure on the

captive screws.

.To avoid damage, place the line card

horizontally on a at antistatic surface.

The outer packaging box contains an

antistatic pink roller foam that can be used

for this purpose.

.Retain the dust caps on the line card

throughout the installation procedure.

Also, use dust caps on unused ports in the

line card.

Cisco ASR 9000 Series

Line Card

Open the ejector levers on either

side of the line card.

Carry the line card and slide the card

into the slot to connect with the

backplane connector. Start with the

lowest numbered line card slot.

Attach an antistatic wrist strap to your

wrist and to the ESD socket of the

chassis, or to a bare metal surface on

the chassis or frame.

1 2 3

Pivot the ejector levers to seat the

card into the backplane connector.

4Repeat Step 2 through Step 5 to

install another line card.

To uninstall a line card, perform the steps in

the reverse order.

For manual OIR (online insertion and removal)

of cards, disengage the line card from the

backplane connector, and partially pull out

the line card. Reseat the card to

establish the connection again.

65 Tighten the captive screws on either

side of the line card to a torque of

10 1 in-lb.

This procedure explains installing the line

card in the horizontal position.

To install the line card in the vertical

position, follow the same steps but

hold the card vertically.

Captive screws

Ejector lever (closed)

Ejector lever (open)

Ejector lever

Captive screws

Antistatic

wrist band

Ensure to verify the eectiveness of

ESD wrist strap before handling the

hardware.

ESD socket

Line card 3

Cable bundle

Cable management bracket

Slot 1

Line card 0

Slot 4 Cable management

bracket

Cable bundle

Line card 0

Slot 5

Slot 3

Line card 3

Cable management tray

Dividers

Cable bundle routed

through the tray

Hinged cover in raised position

DividersCable bundle routed

through the tray

Cable management tray

Cisco ASR 9000 Series

Line Card

Chassis cable management bracket

Install the cable management bracket on one side of the

chassis.

Cisco ASR 9904 Router Cisco ASR 9006 Router

Cisco ASR 9010 Router

Cisco ASR 9910 Router

Route the cable bundle from the line card through the cable

management bracket slot. Each line card has its own cable

routing slot.

Each line card has its own cable routing divider in the

cable management tray. Route the cable or cable bundle

from the line card through the dividers of the cable

management tray.

1(Cisco ASR 9010 Router) Raise the hinged cover to

increase access to the dividers.

Cable Management

Cable management can be achieved by

routing the cables through the following

brackets:

1. Chassis cable management bracket.

2. Cable management tray.

Note: Use cable dust cap to protect the

cables from dust when the cables are

not in use.

Cable management brackets keep the

cables organized. Ensure cables from other

equipment installed in the rack do not

restrict access to the card cages.

To avoid noise interference in network

interface cables, do not route them directly

across or along power cables.

Cable management tray

Cisco ASR 9000 Series

Line Card

Chassis Airow

ESD

Compatible Modules

Replacement

Provide unrestricted airow by maintaining adequate clearance at both the inlet and exhaust openings of the chassis and the

power modules. For more details on chassis airow clearance, click here.

Prevent any airow obstruction that may be caused by cables or blocked lters. Manage and route the cables in ideal directions to

prevent such airow obstructions.

Maintenance Best Practices

ESD

While performing any function or replacement on the chassis, ensure that you use an ESD-preventive antistatic wrist strap

(or ankle strap) to avoid damage by static electricity.

Periodically, check the resistance value of the ESD-preventive strap. The measurement should be between 1 and 10 M Ohm.

For more details, click here.

Replacement

Inspect air lters once every 3 months. If there is an increase in temperature, please check the air lters and fans for any

malfunctioning. For troubleshooting, reach out to Cisco TAC and isolate any possible hardware failure.

Replace air lters that are clogged or damaged. Cleaning the air lters is not recommended.

Use only compatible versions of power modules and fan trays for operations. For the product datasheet, click here.

Compatible Modules

During maintenance, to avoid dust accumulation and air leakage that can increase the chassis temperature, do not keep the fan tray

slot empty for a long duration.

Packaging

Clean Environment

Operating Temperature

Cisco ASR 9000 Series

Line Card

Packaging

Maintenance Best Practices

Clean Environment

Ensure that the chassis installation site is dust free.

Use ller cards in empty slots to prevent dust accumulation and to maintain proper airow.

Always use dust caps on empty optical ports to prevent dust accumulation and airow leakage.

Clean the optical ports according to standard cleaning procedures.

Maintain good air quality, and check air chemical composition at regular intervals. Impure air with high levels of chemical

concentration can cause corrosion that, in turn, would result in product degradation.

Operating Temperature

While packing and transporting line cards or other modules, use only Cisco provided packaging. Any other improper packaging for

moving equipment may severely damage the product.

Repackage the components the same way as it was packaged at the time of product delivery by including all packaging materials.

Orienting the product incorrectly inside the package may cause damage to the product during transportation.

Always use the ESD cover to wrap the hardware before packing it into packaging cartons. Handle any failed hardware with care, and

use an ESD wrist band or an antistatic bag.

Maintain normal operations by anticipating and correcting environmental anomalies before they approach critical values by properly

planning and preparing your site before you install the router.

If the temperature or power requirement of the line card or the chassis exceeds the operating temperature or power requirement,

a thermal shutdown procedure is initiated as applicable.

Operate the chassis only within the limits of the recommended temperature. For technical specications, refer to the respective

product datasheet- click here.

Grounding

Corrosion

Cisco ASR 9000 Series

Line Card

Grounding

Ensure that all equipment racks are grounded to the building. Otherwise, it can pose a serious safety risk to personnel.

Additionally, an electrical current can cause operational deciencies or expose the networking equipment to the risk of permanent

failure due to ESD risks.

Verify the eectiveness of a good ground connection using a multimeter. The multimeter readings should display less than 1 Ohm

for good point-to-point resistivity.

Maintenance Best Practices

For more details on grounding, click here.

Corrosion

Over a period of time, corrosion can degrade the performance of the components. It leads to blocked currents, brittle connection

points, and overheated electrical systems. As chemical reactions continue, the corrosion by-products form insulating layers on

circuits, and they usually cause electronic failure, short circuits, pitting, and metal loss. Therefore, ensure that the maximum

concentration of contaminants for indoor installation does not exceed the prescribed limit.

Avoid touching contacts on modules and protect the equipment from extreme temperatures and moist, salty environments. Monitor

the environmental factors that impact the corrosion rate: ambient pressure, humidity, and temperature. Whenever possible, ensure

that the installation site is fully air conditioned to ensure that the environmental factors are under control.

Install real-time corrosion measurement systems. Corrosion monitors enable you to take preventive action before serious

damage occurs.

The use of HEPA lters is advised to maintain clean air circulation systems.

Avoid using direct air cooling on the product (network equipment).

Autres manuels pour ASR 9000 Series

Table des matières

Autres manuels Cisco Routeur réseau

Cisco

Cisco XR 12404 Manuel utilisateur

Cisco

Cisco IR809 Manuel utilisateur

Cisco

Cisco ASR-920-8S4Z-PD Manuel

Cisco

Cisco vEdge Series Manuel

Cisco

Cisco 820 Series Manuel utilisateur

Cisco

Cisco MWR 1941-DC - 1941 Mobile Wireless Router Manuel utilisateur

Cisco

Cisco 1600 series Manuel utilisateur

Cisco

Cisco Router Cisco 831 Manuel

Cisco

Cisco MWR 1941-DC - 1941 Mobile Wireless Router Manuel utilisateur

Cisco

Cisco CRS-1 - Carrier Routing System Router Manuel utilisateur

Cisco

Cisco SB 106 Manuel utilisateur

Cisco

Cisco 1841 - 3G Bundle Router Manuel

Cisco

Cisco 1003 Manuel utilisateur

Cisco

Cisco 3200 Series Guide d'application

Cisco

Cisco 7206 - VXR Router Manuel utilisateur

Cisco

Cisco ME 4924-10GE Instructions originales

Cisco

Cisco 880 Series Manuel

Cisco

Cisco CRS Manuel utilisateur

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Mode d’emploi

Cisco

Cisco 2431 - IAD Router Manuel

Cisco

Cisco 1861 Series Manuel utilisateur

Cisco

Cisco IR1101 Manuel

Cisco

Cisco A9K-SIP-700 Manuel

Cisco

Cisco Cisco 12416 Manuel de l'opérateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur