Cisco RV Series Manuel utilisateur

Table des matières

Autres manuels Cisco Routeur réseau

Cisco

Cisco 1840 Instructions originales

Cisco

Cisco ASR 9000 Series Manuel utilisateur

Cisco

Cisco Linksys E900 Manuel utilisateur

Cisco

Cisco 12016 Manuel utilisateur

Cisco

Cisco Linksys EA2700 Manuel utilisateur

Cisco

Cisco 2821 - Integrated Services Router Unified Communications... Guide d'installation

Cisco

Cisco 8800 Series Manuel

Cisco

Cisco 3600 Series Manuel

Cisco

Cisco 1750 Guide d'installation

Cisco

Cisco Firepower 1120 Manuel

Cisco

Cisco 1750 Manuel utilisateur

Cisco

Cisco CRS-1 - Carrier Routing System Router Manuel

Cisco

Cisco 4948 Series Manuel utilisateur

Cisco

Cisco XR 12000 Manuel d'installation

Cisco

Cisco LINKSYS E2500V3 Manuel utilisateur

Cisco

Cisco LINKSYS RangePlus WRT100 Manuel utilisateur

Cisco

Cisco ASR 1000 Series Manuel utilisateur

Cisco

Cisco Cisco 881 Manuel utilisateur

Cisco

Cisco RV160 Manuel utilisateur

Cisco

Cisco AIRONET CB21AG Manuel utilisateur

Cisco

Cisco 1700 series Manuel utilisateur

Cisco

Cisco 220 Series Smart Plus Mode d’emploi

Cisco

Cisco ASR 900 Series Manuel utilisateur

Cisco

Cisco 4000 Series Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur

●

●

●

●

Configure Internet Protocol (IP) Mode on an

RV Series Router

Objective

The Internet Protocol (IP) Mode tells your router what IP version your local network is using

in comparison to what version the Wide Area Network (WAN) uses. It is important to

configure this option correctly as certain features may or may not be available on your router

depending on what the state of your network is.

This article aims to show you how to configure the IP Mode on an RV Series Router.

Applicable Devices

RV Series

Software Version

1.0.3.16 — RV130, RV130W

1.0.0.17 — RV132W

1.0.0.21 — RV134W

Configure IP Mode

Step 1. Log in to the web-based utility and choose Networking > IP Mode.

Note: The images on this article are taken from the RV130W router. Menu options may vary

per model.

Step 2. In the IP Mode field, choose an option from the drop-down list.

●

●

●

●

●

●

●

●

If you are using RV130 or RV130W, the options are:

LAN:IPv4, WAN:IPv4 — Both the LAN and the WAN use IPv4.

LAN:IPv6, WAN:IPv4 — Use this if the LAN only uses IPv6 but the WAN uses IPv4. If you

choose this option, you may proceed to the Static 6to4 DNS section.

LAN:IPv6, WAN:IPv6 — Both the LAN and the WAN use only IPv6.

LAN:IPv4+IPv6, WAN:IPv4 — The LAN uses both IPv4 and IPv6, but the WAN only uses

IPv4. If you choose this option, you may proceed to the Static 6to4 DNS section.

LAN:IPv4+IPv6, WAN:IPv4+IPv6 — Both the LAN and the WAN use IPv4 and IPv6.

LAN:IPv4, WAN:IPv6 — The LAN uses IPv4, but the WAN uses IPv6.

If you are using the RV132W or RV134W router, the options are:

LAN:IPv4, WAN:IPv4 — Both the LAN and the WAN use IPv4.

LAN:IPv4+IPv6, WAN:IPv4+IPv6 — Both the LAN and the WAN use IPv4 and IPv6.

Step 3. Click Save.

Step 4. Click OK on the notification telling you that you will now be redirected to the new

default IP address of the router. If the page is not redirected automatically in 2-3 minutes,

enter the new IPv4 or IPv6 address to log in to the router.

Static 6to4 DNS (RV130 and RV130W only)

If you chose LAN:IPv6, WAN:IPv4 or LAN:IPv4+IPv6, WAN:IPv4 from the IP Mode drop-

down list, the Show Static 6to4 DNS Entry will become enabled. It allows IPv6 packets to be

transmitted over an IPv4 network. The 6to4 tunneling is typically used when a site or end

user wants to connect to the IPv6 Internet using the existing IPv4 network. Configuring this

feature is optional and available only on RV130 and RV130W.

Step 1. Click the Show Static 6to4 DNS Entry button to display the Domain to IP address

table. This table is used to map domais to IP addresses, so that a user is redirected to a

corresponding IP address when using the domain.

Step 2. In the Domain 01 field, enter a domain that you want to redirect to an IP address.

You can use up to five domains.

Note: In this example, the domain used is cisco.com.

Step 3. For each domain, enter the IP address on the corresponding IP field.

Note: In this example, the IP address is 10.10.242.242.

Step 4. Click Save.

Step 5. Click OK on the notification telling you that you will now be redirected to the new

default IP address of the router. If the page is not redirected automatically in 2-3 minutes,

please enter the new IPv4 or IPv6 address to log in to the router.

You should now have successfully configured the IP mode on your RV Series Router.