Cisco WBPN Manuel utilisateur

Cisco Small Business

WBPN Wireless-N Bridge for Phone Adapters

USER GUIDE

December 2011

Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found

at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply

a partnership relationship between Cisco and any other company. (1005R)

Cisco WBPN User Guide 3

Contents

Chapter 1: Installing the WBPN Wireless-N Bridge for Phone Adapters 5

Before You Begin 5

Using the WBPN With the Cisco SPA525G/525G2 5

Getting to Know the WBPN 6

Connecting the WBPN Using WPS 8

Using the WPS Push Button Method 8

Using the WPS PIN Method 9

Connecting the WBPN Using a PC 9

Using the Setup Wizard 10

Choosing a Username and Password 10

Configuring Local Area Network Settings 10

Configuring the Wireless Connection 10

Setting a Static IP Address on Your PC 11

Installing the WBPN Into the SPA Phone Stand 16

Chapter 2: Using the WBPN Wireless-N Bridge for Phone Adapters

Configuration Utility 19

Logging in to the Configuration Utility 19

Navigating through the Pages 20

Viewing Status Information 21

Configuring Wired Parameters 23

Configuring LAN Settings 23

Configuring Date and Time Settings 24

Configuring Wireless Parameters 24

Configuring Basic Settings 24

Configuring Advanced Settings 26

Discovering Available Wireless Networks 28

Using Wi-Fi Protected Setup (WPS) 29

Performing Administrative Tasks 30

Viewing Logs 30

Upgrading Firmware 31

Saving and Reloading Your Configuration 31

Cisco WBPN User Guide 4

Contents

Changing Your Username or Password 31

Rebooting and Restoring to Factory Default 32

Appendix A: Where to Go From Here 33

Cisco WBPN User Guide 5

Installing the WBPN Wireless-N Bridge for

Phone Adapters

This chapter describes how to install and initially configure your WBPN Wireless-N

Bridge for Phone Adapters. It contains the following sections:

•Before You Begin, page 5

•Getting to Know the WBPN, page 6

•Connecting the WBPN Using WPS, page 8

•Connecting the WBPN Using a PC, page 9

•Installing the WBPN Into the SPA Phone Stand, page 16

Before You Begin

Before you begin the installation, make sure that you have the following equipment

and information:

•Power Supply for your Small Business IP Phone (not included)

•PC to use the web-based system management tools to configure the WBPN

(required if you are not using Wi-Fi Protected Setup). The web-based

configuration manager is supported on Microsoft Internet Explorer (version

8 or higher) and Mozilla Firefox (version 3.6.3 and higher).

Using the WBPN With the Cisco SPA525G/525G2

You can use the WBPN with the Cisco SPA525G/525G2 IP phone to improve the

wireless performance of the phone. You must first disable the internal Wireless-G

controller on the Cisco SPA525G in order to use the WBPN as your wireless

controller. To disable the phone’s internal wireless:

Installing the WBPN Wireless-N Bridge for Phone Adapters

Getting to Know the WBPN

Cisco WBPN User Guide 6

STEP 1 Press the Setup button and choose Network Configuration.

STEP 2 Under

Wi-Fi

, press the right arrow on the navigation button until Wi-Fi is disabled

(the check mark does not appear).

STEP 3 Choose Set, then Back and Exit to return to the main menu.

Getting to Know the WBPN

Figure 1 WBPN Connections

283688

1 2 3

Installing the WBPN Wireless-N Bridge for Phone Adapters

Getting to Know the WBPN

Cisco WBPN User Guide 7

Figure 2 Phone Connections

1 Power adapter port

2 WBPN power cable

3 Network cable

4 Reset button

5 Wi-Fi Protected Setup (WPS) button

6WLANLED

7WPSLED

8SystemLED

283689

1 Power adapter port

2Ethernetport

Installing the WBPN Wireless-N Bridge for Phone Adapters

Connecting the WBPN Using WPS

Cisco WBPN User Guide 8

Connecting the WBPN Using WPS

If your wireless device supports Wi-Fi Protected Setup (WPS), you can connect

the WBPN to the phone and use WPS to connect the phone your network. If you do

not use WPS, you must connect the WBPN to a PC and use a web browser to

configure it. See the “Connecting the WBPN Using a PC” section on page 9.

STEP 1 If the IP phone power adapter is connected to your IP phone, disconnect it.

STEP 2 Unplug the IP phone power adapter from the power source.

STEP 3 Connect the WBPN power cable to the power port on the IP phone (labeled #1 in

the “Phone Connections” graphic).

STEP 4 Connect the network cable from the WBPN to the Ethernet port on the IP phone

(labeled #2 in the “Phone Connections” graphic).

STEP 5 Connect the IP phone power adapter to the power port on the WBPN (labeled #1

in the “WBPN Connections” graphic).

STEP 6 (Optional) Place the WBPN inside the hollow desktop phone stand. See “Installing

the WBPN Into the SPA Phone Stand” section on page 16.

STEP 7 Plug the IP phone power adapter into the power source.

Using the WPS Push Button Method

STEP 1 After all connections are made and devices are powered on, press the WPS

button on your wireless device.

STEP 2 Press the WPS button on the WBPN. The WPS LED on the WBPN flashes green

during the discovery period.

STEP 3 After the WBPN establishes a connection to the wireless device, the WPS LED

displays solid green, and the WLAN LED will display either solid green or flashing

green, depending on network activity.

Installing the WBPN Wireless-N Bridge for Phone Adapters

Connecting the WBPN Using a PC

Cisco WBPN User Guide 9

Using the WPS PIN Method

STEP 1 Connect the WBPN and power on all devices as previously described.

STEP 2 On the bottom of the WBPN unit, locate the label and make note of the PIN. The PIN

is a unique numeric code printed on the label.

STEP 3 Connect to your wireless device’s web interface using a web browser. Your

computer must be connected to your wireless network.

STEP 4 In your router or device’s WPS menu, enter the WBPN PIN into the field that allows

you to set up wireless devices using a PIN.

STEP 5 Save your changes. The device should automatically connect to the WBPN. After

the WBPN establishes a connection to the wireless device, the WPS LED displays

solid green, and the WLAN LED will display either solid green or flashing green,

depending on network activity.

Connecting the WBPN Using a PC

STEP 1 Connect the IP phone power adapter to the WBPN power adapter port (labeled

#1 in the “WBPN Connections” graphic).

STEP 2 Connect the WBPN network cable (labeled #3 in the “WBPN Connections”

graphic) to the Ethernet port on your PC.

STEP 3 Set your PC’s IP address to a static IP address on the same subnet as the WBPN.

See Setting a Static IP Address on Your PC.

STEP 4 Open your web browser and enter the default IP address for the WBPN:

192.168.1.254.

STEP 5 Enter the default username (cisco) and password (cisco). You should change the

default username and password as soon as possible using the Setup Wizard or by

choosing Administration > Change Password in the management interface.

STEP 6 Follow the steps in the Setup Wizard to configure the WBPN. See the following

sections for more information.

Installing the WBPN Wireless-N Bridge for Phone Adapters

Connecting the WBPN Using a PC

Cisco WBPN User Guide 10

Using the Setup Wizard

The Setup Wizard guides you through configuration of the WBPN. See the

following sections for more information.

Choosing a Username and Password

You must enter a new username and password. The default username and

password (cisco) is not allowed. Passwords must be a minimum of one character

and a maximum of 30 characters.

Configuring Local Area Network Settings

Choose Automatic (DHCP) if you want your network router to assign an IP address

to the WBPN when it is connected to the network. This IP address can change if

the device is disconnected and connected again.

Choose Static IP if you want the WBPN to always have the same IP address on the

network. Enter the IP address you want to assign to the WBPN, the subnet mask,

and the default gateway (the IP address of your network router).

TIP If you choose DHCP or you change the IP address to an address that is different

from the default IP address, you will need to use that new address if you want to

connect your PC to the device later for additional configuration.

Configuring the Wireless Connection

Choose the type of wireless configuration method:

Automatically Using WPS

If your wireless device supports Wi-Fi Protected Setup (WPS), you can choose

this option to connect the phone your wireless network. Then choose the type of

WPS configuration:

•PIN Number—Click Start PIN to begin WPS configuration via the PIN

number. After clicking Start PIN, on your wireless device, go to the WPS

configuration menu and enter the PIN of the WBPN. (The WBPN PIN is

displayed above the Start PIN button on the Wireless WPS window.) You

must enter the WBPN PIN number in your wireless device’s WPS

configuration menu within two minutes of clicking the Start PIN button.

•Push Button Configuration—Click Start PBC to begin WPS configuration via

push button. After clicking PBC, within two minutes, click the WPS push

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco ASR 5000 Series Manuel utilisateur

Cisco

Cisco NAC3350-PROF-K9 - NAC Profiler Server Manuel utilisateur

Cisco

Cisco Cisco ASA Series Manuel utilisateur

Cisco

Cisco ONS 15454 SDH Manuel

Cisco

Cisco ASR 9000 Series Manuel utilisateur

Cisco

Cisco GS7000 Mode d'emploi

Cisco

Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... Manuel utilisateur

Cisco

Cisco NCS 4201 Manuel

Cisco

Cisco FPR1150-ASA-K9 Manuel

Cisco

Cisco ONS 15454 Series Manuel

Cisco

Cisco IPS-4240-K9 - Intrusion Protection Sys 4240 Manuel utilisateur

Cisco

Cisco SCE8000 GBE Manuel de l'opérateur

Cisco

Cisco 5500 Series Manuel utilisateur

Cisco

Cisco UCS-FI-6332-16UP Manuel utilisateur

Cisco

Cisco Aironet 340 Series Manuel utilisateur

Cisco

Cisco Octal-Port DMT ATU-C Line Card Manuel technique

Cisco

Cisco NCS 4016 Manuel utilisateur

Cisco

Cisco ONS 15540 ESP Manuel

Cisco

Cisco NCS 2002 Mode d’emploi

Cisco

Cisco ONS 15310-MA Manuel utilisateur

Cisco

Cisco Linksys Business Series Network Storage System... Manuel utilisateur

Cisco

Cisco ME 1200 Series Manuel

Cisco

Cisco AGS+ Mode d’emploi

Cisco

Cisco MERAKI MX75 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur