Cisco NCS 2002 Mode d’emploi
Installing the Air Flow Regulator
This chapter explains how to install the regulators to maintain the air flow for ANSI and ETSI configurations
in NCS 2002 shelf.
The air flow within the equipment must be maintained at a nominal temperature. This task can be accomplished
using one of these mechanisms:
• Air deflector
• Air plenum
The sections are:
•Air Deflector, on page 1
•Air Plenum, on page 1
•Air Plenum Rack and Cabinet Compatibility, on page 3
•NTP-L42 Install the Air Plenum in NCS 2002 Shelf, on page 4
Air Deflector
An air deflector is a sheet-metal part that is mounted on the NCS 2002 shelf to orient the air flow in a specific
direction.
The air deflectors can be mounted in different positions to control the air flow:
• Front to Front— Only ETSI rack
• Front to Back— For ANSI and ETSI racks
• Front to Top— Only ETSI rack
In an ANSI rack, the air deflectors are mounted only on the 23-inch rack configuration.
Air Plenum
Air plenum orients the air flow in the front-to-back direction inside the equipment to be compliant with GR-63
issue 4 requirement.
NCS 2002 air plenum kit has one horizontal and two vertical air plenums. The air that flows from the front
top inlet are channelized to the right vertical plenum, inside the equipment, and then to the exhaust air channel
towards the left vertical air plenum. The air flow is deflected by 90 degrees and exited out in the rear end.
The following figure shows the air flow inside the air plenum.
Installing the Air Flow Regulator
1
Figure 1: Air flow within the air plenum
The following figures show the dimensions of the air plenum relative to the cabinet or rack.
Figure 2: Dimension of Cisco NCS 2002 chassis relative to the air plenum
Installing the Air Flow Regulator
2
Installing the Air Flow Regulator
Air Plenum
Figure 3: Dimension of Cisco NCS 2002 chassis relative to the air plenum
Air Plenum Rack and Cabinet Compatibility
The table shows the compatibility of air plenum with the ANSI and ETSI racks and cabinets. The chassis can
be installed with brackets in front position only.
Table 1: Air plenum compatibility with racks and cabinets
Front-to-back air flowRack / Cabinet
Supported 1
ANSI 19-inch rack
Supported 1
ANSI 19-inch cabinet
SupportedANSI 23-inch rack
SupportedANSI 23-inch cabinet
Supported 1
ETSI cabinet
1A minimum opening of 20.600 inches is required to install the vertical air plenum behind the front rails.
The ANSI 19-inch two post rack that is compatible with air plenum installation is available from Telect, with
part number 12545-301.
Note
Installing the Air Flow Regulator
3
Installing the Air Flow Regulator
Air Plenum Rack and Cabinet Compatibility
Figure 4: Minimum rear opening for ANSI 19-inch and ETSI configuration
NTP-L42 Install the Air Plenum in NCS 2002 Shelf
This procedure installs the air plenum to orient the air flow in front-to- back direction
in the NCS 2002 shelf.
Purpose
• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver
• Screws
• ANSI: #12-24 x 0.50 pan-head Phillips screws
• ETSI: M6.0 x 20 pan-head Phillips screws
• Wing head screws (4)
• Adapter plates
• One air plenum kit (horizontal and vertical air plenums)
Tools/Equipment
As neededRequired/As Needed
OnsiteOnsite/Remote
NoneSecurity Level
Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1074
Warning
Before working on a chassis or working near power supplies, unplug the power cord on AC units.
Statement 246
Warning
Installing the Air Flow Regulator
4
Installing the Air Flow Regulator
NTP-L42 Install the Air Plenum in NCS 2002 Shelf
This equipment is intended to be grounded. Ensure that the host is connected to earth ground during
normal use. Statement 39
Warning
For nominal voltage of -60 VDC, the input voltage range is from -40 to -72 VDC.
Note
Use only the fastening hardware provided with the NCS 2002 to prevent loosening, deterioration, and
electromechanical corrosion of the hardware and joined material.
Note
When installing or replacing the unit, the ground connection must always be made first and disconnected
last. Statement 1046
Warning
The air plenum is installed on a rack or a cabinet using thread-forming screws that remove any paint
or non-conductive coatings inside the hole threads, and establish a metal-to-metal contact. Also, clean
both surfaces outside the screw points that come in contact, so that they are free of paint and other
nonconductive coating. Apply an appropriate antioxidant compound to the surfaces.
Warning
Procedure
Depending on the rack or cabinet, complete the necessary task:
•DLP-L65 Installing Air Plenum for NCS 2002 Shelf in ANSI 19-inch Configuration, on page 5
•DLP-L69 Installing Air Plenum in NCS 2002 Shelf for ANSI 23-inch Configuration, on page 8
•DLP-L70 Installing Air Plenum for NCS 2002 Shelf in ETSI Configuration, on page 13
•DLP-L71 Installing Pre-assembled Air Plenums in ANSI 23-inch Configuration, on page 12
Stop. You have completed this procedure.
DLP-L65 Installing Air Plenum for NCS 2002 Shelf in ANSI 19-inch Configuration
This task installs the air plenum for the NCS 2002 shelf in ANSI 19-inch cabinet or
rack configuration.
Purpose
Installing the Air Flow Regulator
5
Installing the Air Flow Regulator
DLP-L65 Installing Air Plenum for NCS 2002 Shelf in ANSI 19-inch Configuration
• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver
• Screws: #12-24 x 0.50 pan-head Phillips screws (4)
• Wing head screws (4)
• One air plenum kit (horizontal and vertical air plenum)
Tools/Equipment
As neededRequired/As Needed
OnsiteOnsite/Remote
NoneSecurity Level
In the 19-inch rack and cabinet, the air plenum can be mounted only if the minimum opening is 20.600 inches
to install the vertical air plenums behind the front rails.
Note
Procedure
Step 1 Place the horizontal air plenum above the shelf slot in the ANSI 19-inch cabinet or rack.
Step 2 Insert the wing head screws provided with the kit, and tighten to a torque value of 11.5 in-lb (1.3 N-m).
Figure 5: Installing the horizontal air plenum in the ANSI 19-inch configuration
Step 3 Install the vertical air plenum to the left of the horizontal air plenum:
a) Insert the vertical plenum in the free space between the horizontal plenum and cabinet.
b) Install t he wing head screws fom the internal side of the horizontal plenum as shown in the following
figure.
c) Tighten the screws to a torque value of 11.5 in-lb (1.3 N-m).
Installing the Air Flow Regulator
6
Installing the Air Flow Regulator
DLP-L65 Installing Air Plenum for NCS 2002 Shelf in ANSI 19-inch Configuration
Figure 6: Installing the left vertical air plenum
Step 4 Install the vertical air plenum to the right of the horizontal air plenum. Follow step 3a to 3c.
Figure 7: Installing the right vertical air plenum
Step 5 Install the 19-inch standard brackets on both sides of the chassis in the front position. See DLP-L35 Mounting
the 19-inch Brackets on the NCS 2002 Shelf for ANSI Rack Configuration.
Step 6 Install the NCS 2002 empty chassis below the horizontal plenum.
Installing the Air Flow Regulator
7
Installing the Air Flow Regulator
DLP-L65 Installing Air Plenum for NCS 2002 Shelf in ANSI 19-inch Configuration
Figure 8: Installing the NCS 2002 chassis below the horizontal air plenum
Step 7 Return to your originating procedure (NTP).
DLP-L69 Installing Air Plenum in NCS 2002 Shelf for ANSI 23-inch Configuration
This task installs the air plenum for the NCS 2002 shelf in the ANSI 23-inch cabinet
or rack configuration.
Purpose
• #2 Phillips Dynamometric screwdriver
• Medium slot-head screwdriver
• Small slot-head screwdriver
• Screws: #12-24 x 3/4 pan-head Phillips mounting screws (4)
• Wing head screws (4)
• Adapter plates
• One air plenum kit (horizontal and vertical air plenum)
Tools/Equipment
As neededRequired/As Needed
OnsiteOnsite/Remote
NoneSecurity Level
The air plenums for ANSI 23-inch configuration can also be pre-assembled outside the cabinet and then
installed inside the cabinet. See DLP-L71 Installing Pre-assembled Air Plenums in ANSI 23-inch Configuration,
on page 12
Note
Installing the Air Flow Regulator
8
Installing the Air Flow Regulator
DLP-L69 Installing Air Plenum in NCS 2002 Shelf for ANSI 23-inch Configuration
Procedure
Step 1 Install the ANSI 23-inch adapter plates on the horizontal air plenum.
Step 2 Align the screws to fix the adapter plates to the shelf. Insert the screws and tighten them to a torque value of
11.5 in-lb (1.3 N-m).
Figure 9: Installing the adapter plates on the horizontal air plenum
Step 3 Place the horizontal air plenum above the shelf slot in the ANSI 23-inch cabinet or rack.
Step 4 Insert the wing head screws provided with the kit, and tighten to a torque value of 11.5 in-lb (1.3 N-m).
Installing the Air Flow Regulator
9
Installing the Air Flow Regulator
DLP-L69 Installing Air Plenum in NCS 2002 Shelf for ANSI 23-inch Configuration
Figure 10: Installing the horizontal air plenum in the ANSI 23-inch configuration
Step 5 Install the vertical air plenum to the left of the horizontal air plenum:
a) Insert the vertical air plenum in the free space between the horizontal air plenum and cabinet.
b) Install the wing head screws from the internal side of the horizontal plenum as shown in the following
figure.
c) Tighten the screws to a torque value of 11.5 in-lb (1.3 N-m).
Figure 11: Installing the left vertical air plenum
Step 6 Install the vertical plenum to the right of the horizontal air plenum. Follow step 5a to 5c.
Installing the Air Flow Regulator
10
Installing the Air Flow Regulator
DLP-L69 Installing Air Plenum in NCS 2002 Shelf for ANSI 23-inch Configuration
Table des matières
Autres manuels Cisco Matériel réseau
Cisco
Cisco Firepower 1100 Series Manuel
Cisco
Cisco ASR 9000 Series Manuel utilisateur
Cisco
Cisco 5400 Manuel utilisateur
Cisco
Cisco 8540 - Catalyst Campus Switch Router Modular Expansion... Manuel utilisateur
Cisco
Cisco MultiRIP Ethernet Card Manuel utilisateur
Cisco
Cisco MERAKI MX75 Manuel utilisateur
Cisco
Cisco NCS 6008 LCC Mode d’emploi
Cisco
Cisco NM-1A-T3 - 1port Ds3 Atm Network Module Manuel utilisateur
Cisco
Cisco Secure Network Server 3700 Series Manuel
Cisco
Cisco Mc3810 - 16MB Flash Memory Guide rapide
Cisco
Cisco MGX 8260 Guide de démarrage rapide
Cisco
Cisco CATALYST 6000 Manuel d'installation et d'exploitation
Cisco
Cisco GS7000 Manuel utilisateur
Cisco
Cisco CE 2000 Platform SCE 2000 4xGBE Manuel de l'opérateur
Cisco
Cisco Engine 611 Manuel utilisateur
Cisco
Cisco IPS-4260-K9 - IPS Sensor 4260 Manuel utilisateur
Cisco
Cisco Catalyst 2960-XR Manuel utilisateur
Cisco
Cisco WS-CE500 - Catalyst Express 500-24PC Mode d’emploi
Cisco
Cisco o UCS X440p Instructions d'installation et d'entretien
Cisco
Cisco Prisma EtherLinX Manuel utilisateur
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
