Cisco FirePOWER 8000 Series Manuel utilisateur

Insert and Remove a Network Module (NetMod) on

an 8000 Series FirePOWER Appliance

Document ID: 118194

Contributed by Nazmul Rajib and Josiah Zimmermann, Cisco TAC

Engineers.

Aug 06, 2014

Contents

Introduction

Prerequisites

Before You Begin

Required Tool and Hardware

Remove the Module or Slot Cover

Insert a Module or Slot Cover

Introduction

Instead of the usual fixed port configuration of most high−end security appliances, the modularity of the 8000

Series appliances enables you to choose and change the number and type of interfaces for the appliance.

Various Network Modules (NetMods) are inserted into the 8000 Series appliances to customize the interface

configuration to match your network requirements. This document describes how to insert and remove a

NetMod in an 8000 series FirePOWER appliance.

Caution: If you install a NetMod in an incompatible slot on your appliance or a NetMod is otherwise

incompatible with your system, an error or warning message appears in the web interface on the managing

Defense Center when you attempt to configure the NetMod.

Prerequisites

Before You Begin

Before you begin, prepare to insert or remove your module using the following guidelines:

Identify all appliance and module parts.• Identify the slots where you want to install your NetMods.• Identify the correct slots for your stacking modules.• Confirm that the EMI gaskets are in place.• Unplug all power cords from the appliance.•

Warning: You cannot hot−swap modules. You must power down and unplug both power cords from the

appliance before inserting or removing modules.

Caution: Use proper electrostatic discharge (ESD) practices such as wearing wrist straps and using an ESD

work surface when handling the modules. Store unused modules in an ESD bag or box to prevent damage.

Required Tool and Hardware

T8 Torx screwdriver• 8000 Series FirePOWER appliance•

Remove the Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to release the latch.

Step 3: Slide the module out of the slot.

Insert a Module or Slot Cover

Step 1: Remove and reserve the T8 Torx screw from the lever of the module using the T8 Torx screwdriver.

Step 2: Pull the lever away from the module to open the latch. The near end of the latch is visible. The far

end of the latch is inside the module.

Step 3: Insert the module into the slot until the far end of the latch is inside the slot and the near end of the

latch touches the outside of the slot.

Step 4: Push the lever toward the module so that the latch engages and pulls the module into the slot.

Step 5: Press firmly on the screw hole to push the lever fully against the module to secure the latch.

Step 6: Insert and tighten the reserved T8 Torx screw into the lever.

Updated: Aug 06, 2014 Document ID: 118194

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco Catalyst X6148 Manuel utilisateur

Cisco

Cisco Aironet 340 Series Comment utiliser

Cisco

Cisco 2600 Series Document technique

Cisco

Cisco ONS 15327 Manuel

Cisco

Cisco CPS-MSP-1RU-K9 Manuel utilisateur

Cisco

Cisco ONS 15454 Manuel utilisateur

Cisco

Cisco Linksys Business Series Network Storage System... Manuel utilisateur

Cisco

Cisco 3660 Series Manuel utilisateur

Cisco

Cisco ONS 15454 Mode d’emploi

Cisco

Cisco LightStream 1010 Manuel

Cisco

Cisco ONS 15454 Feuille d'instructions

Cisco

Cisco ASA 5506-X Manuel

Cisco

Cisco CX-TRIP2 Manuel de l'opérateur

Cisco

Cisco NCS 1000 Manuel utilisateur

Cisco

Cisco Cisco ASA Series Manuel utilisateur

Cisco

Cisco RSP7000 Mode d’emploi

Cisco

Cisco Content Engine 510 Manuel utilisateur

Cisco

Cisco Performance Routing Engine 5 Manuel

Cisco

Cisco IAD2430 Series Manuel

Cisco

Cisco NM-1FE-TX - Interface Module Ethernet Manuel utilisateur

Cisco

Cisco CSC-C2FCIT Mode d’emploi

Cisco

Cisco ON100 Network Agent Manuel utilisateur

Cisco

Cisco UCS X10c Instructions d'installation et d'entretien

Cisco

Cisco Catalyst 2960-XR Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur