Cisco Aironet 340 Series Manuel utilisateur

TAKE OUT WHAT YOU NEED

CONNECT AND POWER UP THE BRIDGE

DETERMINE CONFIGURATION METHOD

CONFIGURE THE BRIDGE

Quick Start Guide

CISCO AIRONET WORKGROUP BRIDGE

340 AND 350 SERIES

ETHERNET

SPEED

LED

100BaseTX SOLID

10BaseT BLINK

1X 2X 3X 4X

5X 6X 7X MDI MDI-X

Hub

Wired LAN

Workstation

Laptop

Workstation

Workgroup

bridge

File server

Access point

Station with

radio card

39283

Take Out What You Need

If any item is missing or damaged, contact your Cisco representative or reseller for support.

Before You Begin

Before beginning installation, determine bridge location. Because the unit is a radio device, unit

and antenna location are important to ensure optimum radio range and throughput:

• To maximize the range of a building-to-building connection, install the antenna as high as

possible.

• Maintain a clear line of sight between wireless bridge antennas. Obstructions may impede

performance or limit bridge ability to transmit and receive data.

• Place directional antennas at both ends with maximum path clearance.

• Install the bridge in an area where large steel structures such as shelving units, bookcases,

and ﬁling cabinets will not obstruct radio signals to and from the bridge.

• Install the bridge away from microwave ovens.

Cisco Aironet Workgroup Bridge

AC-to-DC power adapter

2.2 dBi dipole antenna

Cisco Aironet Series Workgroup Bridge CD

with product documentation

Connect and Power Up the Bridge

Connecting the Ethernet

Cable

Caution Make sure the unit is

disconnected from the power

source.DonotconnecttheEthernet

cable when the bridge is powered

up.

1Plug the RJ-45 Ethernet connector into

the Ethernet port on the back of the

bridge.

2Connect the other end of the cable to a

hub on the wired LAN, as shown in the

ﬁgure below, or to the Ethernet

connection on the computer that you

will use to conﬁgure the unit.

Note You must use a crossover cable to

connect the bridge directly to the Ethernet

port on a computer. See the Cisco Aironet

Workgroup Bridge Hardware Installation

Guide for a pinout diagram of a crossover

cable.

ETHERNET

SPEED

LED

100BaseTX SOLID

10BaseT BLINK

1X 2X 3X 4X

5X 6X 7X MDI MDI-X

ETHERNET 5VDC

42272

Connecting the Power

Adapter

Follow these steps to connect the power

adapter to the bridge:

1Plug the power adapter into a suitable

power receptacle.

2Plug the power connector into the back

of the bridge.

Note The bridge does not have an on/off

switch, so power is applied to the unit when

you plug it in.

The bridge begins the power-on self-test

(POST) when you apply power. The

indicator lights show the unit’s progress

during startup. The indicators

simultaneously ﬂash red, then amber, and

then green. Startup takes approximately 30

seconds.

ETHERNET 5VDC

39281

Determine Conﬁguration Method

Installing the IP Setup Utility

The IP Setup Utility (IPSU) allows you to

ﬁnd the bridge’s IP address when it has been

assigned by a DHCP server. You may also

use IPSU to set the bridge IP address and

SSID, depending on which conﬁguration

method you choose.

The IPSU cannot query the bridge’s IP

address when the computer running IPSU is

ona differentsubnet thanthe bridge.If your

bridge receives an IP address from a DHCP

server, you must install and run IPSU on a

computer on the same subnet as the bridge.

However, because IPSU uses IP multicast, it

can set the bridge IP address and SSID when

the computer running IPSU is on a different

subnet than the bridge.

Note IPSU may not function correctly if

thecomputer onwhichyou installIPSU uses

Windows 95 or Windows 95A, and the

MicrosoftOfﬁceSuite hasnotbeen installed

on the computer. Install IPSU on another

computer if one is available.

1Put the Cisco Aironet Workgroup

Bridge CD in the CD-ROM drive of the

computer you are using to conﬁgure the

bridge.

2Use Windows Explorer to view the

contents of the CD. Double-click the

IPSU folder, and then double-click the

ﬁle called setup.exe. Follow the steps

provided by the installation wizard.

Conﬁguration Summary

• Choose the conﬁguration method best

suited for your network conﬁguration

and do the initial conﬁguration.

• Conﬁgure the bridge.

• Unplug the power adapter and

disconnect the bridge from the PC or

hub.

• Place the bridge near the device or hub

it will serve. Connect the bridge to the

hub with an Ethernet cable.

Options for Initial

Conﬁguration

You can use one of three methods to

conﬁgure the bridge:

• Use a computer connected to your

wired LAN or wireless network to

communicate with the bridge through a

Cisco Aironet access point. The

computer you use for conﬁguration

must be on the same subnet as the

bridge.

• Use a computer on your wired LAN to

communicate with the bridge through a

hub on your wired LAN. The computer

you use for conﬁguration must be on

the same subnet as the bridge.

• Use a non-networked computer to

communicate directly with the bridge

through a crossover cable.

Wired LAN

Workstation

on the wireless LAN

Workgroup

bridge

File server

Workstation

on the wired LAN

Access point

39276

Determine Conﬁguration Method (continued)

Remote Conﬁguration through an Access Point

Note The workgroup bridge communicates only with Cisco Aironet Access Points.

1Adjust the following settings on the access point to allow it to communicate with the

bridge:

—On the access point’s Express

Setup management page, set

the access point’s SSID to

tsunami, which matches the

bridge’s default SSID.

—On the access point’s AP

Radio Data Encryption

management page, set the

encryption mode to off.

To conﬁgure the bridge using a computer connected to your network with an access point

and DHCP server, continue with Steps 2 through 4.

If you do not have a DHCP server, set your PC to an address of 192.168.200.5. Then open

the browser or Telnet to 192.168.200.1. Skip to the “Conﬁgure the Bridge” section.

2Place the bridge in the vicinity of an access point and plug in the power adapter.

The bridge communicates with the access point when you apply power to the bridge. If

yournetwork usesa DHCPserver,and ifthe bridge’s Ethernetport isconnected toa device,

the bridge receives an IP address on your network. When the bridge’s IP address is changed

from the default setting, it can no longer be set using the IPSU.

3When the status LED on the bridge is green (to show association of the bridge to the access

point), go to the association table. Find the entry WGB3XX_xxxxxx (xxxxxx is the last

six digits of the access point’s MAC address).

4Record the IP address of that entry. Browse to the bridge’s management home page and

complete the conﬁguration by following the steps in the “Conﬁgure the Bridge” section.

ETHERNET

SPEED

LED

100BaseTX SOLID

10BaseT BLINK

1X 2X 3X 4X

5X 6X 7X MDI MDI-X

Wired LAN

Hub on

wired LAN

Ethernet

cable

Workgroup

bridge

Workstation

39284

Determine Conﬁguration Method (continued)

Conﬁguration through a Wired LAN

Note If the bridge is connected to the wired LAN and is communicating with an access point

on the same LAN, a network problem known as a bridge loop can occur. Avoid a bridge loop

by disconnecting the bridge from the wired LAN immediately after you conﬁgure it. For more

information on bridge loops, refer to the Cisco Aironet Workgroup Bridge Hardware

Installation Guide.

1Use a straight-through Ethernet

cable to connect the bridge to a

standard port on a hub on your

wired network.

2Plug in the bridge’s power

adapter. The bridge receives a

DHCP-assigned IP address.

3Double-click the IPSU icon on

your desktop to start the utility.

4When the utility window opens, make sure Get IP addr is selected in the Function box.

5Enter the bridge’s MAC address in the Device MAC ID ﬁeld. The bridge’s MAC address is

printed on the label on the bottom of the unit. It should contain six pairs of hexadecimal

digits.Yourbridge’sMAC addressmight look likethe following example:11223a4D5566.

Note The MAC address ﬁeld is not case-sensitive.

6Click Get IP Address.

7When the bridge’s IP address appears in the IP Address ﬁeld, write it down.

If IPSU reports that the IP address is 192.168.200.1, the default IP address, then the bridge

did not receive a DHCP-assigned IP address. To assign an IP address, go to Step 8. The

computer you use to assign an IP address to the bridge must have an IP address of its own.

If you do not need to assign an address, skip to Step 13.

8Make sure Set Parameters is selected in the Function box of the IPSU window.

9Enter the bridge’s MAC address in the Device MAC ID ﬁeld.

Wired LAN

Workstation

on the wireless LAN

Workgroup

bridge

File server

Workstation

on the wired LAN

Access point

39276

Determine Conﬁguration Method (continued)

10 In the IP Address ﬁeld, enter the IP address the network administator gave you to assign to

the bridge. The IP address of the PC should be on the same subnet as the IP address you

are assigning to the bridge.

11 Enter the SSID you want to assign to the bridge in the SSID ﬁeld.

Note You cannot set the SSID without also setting the IP address. However, you can set the

IP address without setting the SSID.

12 Click the Set Parameters button. You will see a message that the SSID was successfully set.

13 To check the IP address, browse to the bridge’s browser-based management pages.

14 Enter the bridge’s IP address in the browser’s location or address ﬁeld. (If you are using

Netscape, the ﬁeld is labeled Netsite or Location; if you are using Microsoft Explorer, the

ﬁeld is labeled Address.)

15 Press Enter. The bridge’s main menu page appears.

16 Disconnect the unit from your wired LAN and connect it to the hub it will serve.

Local Conﬁguration Using a Non-Networked Computer

If you use a non-networked computer to conﬁgure the bridge, you must use a crossover cable

to connect the computer to the bridge, and the computer must have a TCP/IP network protocol

and IPSU installed.

To use a non-networked computer to conﬁgure the bridge, follow these steps:

1Connect the bridge and a

non-networked PC with a

crossover cable.

2Power on both devices.

3Double-click the IP Setup icon on

your computer desktop.

4When the utility window opens,

make sure Set Parameters is

selected in the Function box.

Determine Conﬁguration Method (continued)

5Enter the bridge’s MAC address in the Device MAC ID ﬁeld. The bridge’s MAC address is

printed on the label on the bottom of the unit. It should contain six pairs of hexadecimal

digits. Your bridge’s MAC address might look like the following example: 11223a4D5566.

Note The MAC address ﬁeld is not case-sensitive.

6In the IP Address ﬁeld, enter the IP address the network administrator gave you to assign

to the bridge. The IP address of the PC should be on the same subnet as the IP address you

are assigning to the bridge.

7Enter the SSID you want to assign to the bridge in the SSID ﬁeld.

Note You cannot set the SSID without also setting the IP address. However, you can set the

IP address without setting the SSID.

8Click Set Parameters.

9To test the IP address, open an Internet browser.

10 Enter the bridge’s IP address in the browser’s location or address ﬁeld. (If you are using

Netscape, the ﬁeld is labeled Netsite or Location; if you are using Microsoft Explorer, the

ﬁeld is labeled Address.)

11 Press Enter. The bridge’s main menu page appears.

Conﬁgure the Bridge

After you choose an initial conﬁguration for the bridge, you can choose to access the bridge’s

management system through your Internet browser or through a Telnet session. Each method

is described below.

Using an Internet Browser

Follow these steps to conﬁgure the bridge with an Internet browser:

1Open an Internet browser.

2Enter the bridge’s IP address in the browser’s location ﬁeld. (If you are using Netscape, the

ﬁeld is labeled Netsite or Location; if you are using Microsoft Explorer, the ﬁeld is labeled

Address.) Press Enter.

3When the bridge’s management home page appears, click Allow Conﬁg Changes in the

upper-left corner.

4In the Conﬁguration menu, click Radio.

Caution Ifyouareconﬁguringthebridgethrougha wireless connection,changingthe

SSIDinthe nextstep could interruptconnectivity to thedevice. Be sureto enteranSSID

that matches the SSID of an access point near the bridge.

5On the Radio page, look at the SSID in the Service set identiﬁer ﬁeld. If it is tsunami, the

default setting, delete it and enter the SSID provided by your network administrator. Click

Save.

If you already set the SSID using IPSU and the SSID in the Service set identiﬁer ﬁeld is

correct, you do not need to set it again.

Note Steps 6 through 15 help you set the bridge’s WEP key. If your wireless network does not

use WEP, skip to Step 16.

6In the Item column on the Radio page, click Privacy conﬁguration.

7In the Privacy conﬁguration menu, click Set the keys.

8Click inside the box labeled Enter a key number from 1 to 4.

Autres manuels pour Aironet 340 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Matériel réseau

Cisco

Cisco DS-X9530-SF1-K9 - Supervisor-1 Module - Control... Manuel utilisateur

Cisco

Cisco CATALYST RPS 2300 Guide de démarrage rapide

Cisco

Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Manuel utilisateur

Cisco

Cisco Fourth-Generation Versatile Interface Processor... Manuel de l'opérateur

Cisco

Cisco WS-CE500 - Catalyst Express 500-24PC Mode d’emploi

Cisco

Cisco CGR 1240 Manuel utilisateur

Cisco

Cisco LightStream 1010 Manuel utilisateur

Cisco

Cisco ISA550 Mode d’emploi

Cisco

Cisco ONS 15454 Mode d’emploi

Cisco

Cisco MC3810 Series Manuel utilisateur

Cisco

Cisco ONS 15310-CL Manuel utilisateur

Cisco

Cisco NCS 1004 Manuel utilisateur

Cisco

Cisco ONS 15200 Series Manuel utilisateur

Cisco

Cisco Aironet 1430 Series Manuel utilisateur

Cisco

Cisco Firepower 9300 Manuel

Cisco

Cisco ONS 15310-MA Manuel utilisateur

Cisco

Cisco Firepower 9300 Guide de maintenance et de service

Cisco

Cisco ONS 15327 Manuel

Cisco

Cisco GS7000 Mode d'emploi

Cisco

Cisco NSS2000 - Gigabit Storage System Chassis Comment utiliser

Cisco

Cisco SA520-K9 - SA 500 Series Security Appliances Manuel utilisateur

Cisco

Cisco CGR 1000 Series Manuel utilisateur

Cisco

Cisco Linksys WES610N Manuel utilisateur

Cisco

Cisco AIR-BR1410A-A-K9 - Aironet 1410 Wireless... Guide de référence rapide

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur