Cisco Nexus 3000 series Mode d’emploi

Installing the Switch Chassis

•Safety, on page 1

•Installation Guidelines, on page 2

•Unpacking and Inspecting the Switch, on page 2

•Attaching L-Brackets to the Chassis, on page 3

•Attaching Magnet to the Chassis, on page 4

•Grounding the Chassis, on page 5

•Starting the Switch, on page 6

Safety

Before you install, operate, or service the switch, see the Regulatory, Compliance, and Safety Information for

the Cisco Nexus 3000 and 9000 Series for important Safety Information.

Statement 1071—Warning Definition

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work

on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard

practices for preventing accidents. Use the statement number provided at the end of each warning to locate

its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

Warning

Statement 1017—Restricted Area

This unit is intended for installation in restricted access areas. A restricted access area can be accessed by

skilled, instructed or qualified personnel.

Warning

Installing the Switch Chassis

Statement 1030—Equipment Installation

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Warning

Installation Guidelines

When installing the switch, follow these guidelines:

• Ensure that there is adequate clearance space around the switch to allow for servicing the switch and for

adequate airflow.

• Ensure that the chassis can be adequately grounded. If the switch is not mounted in a grounded rack, we

recommend connecting the system ground on the chassis directly to an earth ground.

• Ensure that the site power meets the power requirements for the switch. If available, you can use an

uninterruptible power supply (UPS) to protect against power failures.

Avoid UPS types that use ferroresonant technology. These UPS types can become

unstable with the switch, which can have substantial current draw fluctuations

because of fluctuating data traffic patterns.

Caution

• Ensure that circuits are sized according to local and national codes. Typically, this often requires one or

both of the following:

• AC power supplies typically require at least a 15-A or 20-A AC circuit, 100 to 240 VAC, and a

frequency of 50 to 60 Hz.

To prevent loss of input power, ensure the total maximum loads on the circuits

supplying power to the switch are within the current ratings for the wiring and

breakers.

Caution

Statement 1005—Circuit Breaker

This product relies on the building's installation for short-circuit (overcurrent)

protection. Ensure that the protective devices is rated not greater than 20A (North

America), 16A (Europe), and 13A (UK).

Warning

Unpacking and Inspecting the Switch

Before you install the switch, be sure to unpack and inspect the switch for damage or missing components.

If anything is missing or damaged, contact your customer service representative immediately.

Installing the Switch Chassis

Installation Guidelines

Keep the shipping container in case the chassis requires shipping at a later time.

Tip

Before you begin

Before you unpack the switch and before you handle any switch components, be sure that you are wearing a

grounded electrostatic discharge (ESD) strap. To ground the strap, attach it directly to an earth ground or to

a grounded rack or grounded chassis (there must be a metal-to-metal connection to the earth ground).

Check for damage and report any discrepancies or damage to your customer service representative. Have the following

information ready:

• Invoice number of shipper (see packing slip)

• Model and serial number of the damaged unit

• Description of damage

• Effect of damage on the installation

Attaching L-Brackets to the Chassis

You attach two L-brackets to each side of the chassis. These brackets hold the chassis in place on a flat surface.

Before you begin

• You must have the following tools and equipment:

• Phillips-head screwdriver

• L-brackets (4) and screws (4)

Step 1 Align the hole in the L-bracket with the hole on the side of the chassis. Attach the L-bracket with a screw using a

Phillips-head screwdriver. See the following figure.

Installing the Switch Chassis

Attaching L-Brackets to the Chassis

Screw (4)2L-bracket (4)1

Step 2 Use screws to attach the brackets to a flat surface.

Attaching Magnet to the Chassis

You attach the magnet to the bottom of the chassis. The magnet holds the chassis in place on a flat surface.

Before you begin

• You must have the following equipment:

• Chassis magnet

Step 1 Align the magnet to the bottom of the chassis. Attach the magnet to the chassis. See the following figure.

Installing the Switch Chassis

Attaching Magnet to the Chassis

Magnet1

Step 2 Use the magnet on the bottom of the chassis to attach the chassis to a flat surface.

Grounding the Chassis

The switch chassis is automatically grounded when you properly install the switch in a grounded rack with

metal-to-metal connections between the switch and rack.

You can also ground the chassis, which is required if the rack is not grounded, by attaching a customer-supplied

grounding cable. Attach the cable to the chassis grounding pad and the facility ground.

Statement 1024—Ground Conductor

This equipment must be grounded. To reduce the risk of electric shock, never defeat the ground conductor or

operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical

inspection authority or an electrician if you are uncertain that suitable grounding is available.

Warning

Statement 1046—Installing or Replacing the Unit

To reduce risk of electric shock, when installing or replacing the unit, the ground connection must always be

made first and disconnected last.

Warning

Before you begin

Before you can ground the chassis, you must have a connection to the earth ground for the data center building.

Step 1 Use a wire-stripping tool to remove approximately 0.75 inch (19 mm) of the covering from the end of the grounding

wire. We recommend 6-AWG wire for the U.S. installations.

Step 2 Insert the stripped end of the grounding wire into the open end of the grounding lug. Use a crimping tool to crimp the

lug to the wire, see the following figure. Verify that the ground wire is securely attached to the grounding lug by attempting

to pull the wire out of the crimped lug.

Installing the Switch Chassis

Grounding the Chassis

2 M4 screws are used to

secure the grounding lug to

the chassis

3Chassis grounding pad1

Grounding cable, with 0.75

in. (19 mm) of insulation that

is stripped from one end,

which is inserted into the

grounding lug and crimped

in place

Step 3 Secure the grounding lug to the chassis grounding pad with two M4 screws, see the previous figure. Tighten the screws

to 11 to 15 in-lb (1.24 to 1.69 N·m) of torque.

Step 4 Prepare the other end of the grounding wire and connect it to the facility ground.

Starting the Switch

You start the switch by connecting it to its dedicated power source. If you need n+1 redundancy, you must

connect each of the power supplies to one or two power sources. If you need n+nredundancy, you must

connect each power supply in a switch to a different power source.

Before you begin

• The switch must be installed and secured to a rack or cabinet.

• The switch must be adequately grounded.

• The rack must be close enough to the dedicated power source so that you can connect the switch to the

power source by using a designated power cables.

• You have the designated power cables for the power supplies that you are connecting to the dedicated

power sources.

Depending on the outlet receptacle on your AC power distribution unit, you might

need an optional jumper power cord to connect the switch to your outlet receptacle.

Note

• The switch is not connected to the network (this includes any management or interface connections).

Step 1 For the AC power supply, do the following:

a) Using the recommended AC power cable for your country or region, connect one end to the AC power supply.

b) Connect the other end of the power cable to the AC power source.

Step 2 Listen for the fans; they should begin operating when the power supply is powered.

Step 3 After initialization, the switch chassis Status (STS) LED is green.

Step 4 Verify that the system software has booted and the switch has initialized without error messages.

Installing the Switch Chassis

Starting the Switch

Note

A setup utility automatically launches the first time that you access the switch and guides you through the basic

configuration. For instructions on how to configure the switch and check module connectivity, see the appropriate Cisco

Nexus 9000 configuration guide.

Installing the Switch Chassis

Starting the Switch

Installing the Switch Chassis

Starting the Switch

Autres manuels pour Nexus 3000 series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Châssis

Cisco

Cisco UCS C4200 Instructions d'installation et d'entretien

Cisco

Cisco CRS-1 - Carrier Routing System Router Guide de l'utilisateur

Cisco

Cisco cBR Manuel utilisateur

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuel de service

Cisco

Cisco CRS-1 - Carrier Routing System Router Manuel technique

Cisco

Cisco ONS 15454 DWDM Mode d'emploi

Cisco

Cisco NCS 4016 Manuel utilisateur

Cisco

Cisco Network Convergence System 6000 Fabric Card... Manuel

Cisco

Cisco ASA5500-HW - Hardware Accessory Kit Network... Manuel

Cisco

Cisco Firepower 4100/9300 Manuel utilisateur

Cisco

Cisco NCS 1001 Manuel utilisateur

Cisco

Cisco NCS 4016 Mode d’emploi

Cisco

Cisco 6160 Manuel d'utilisation et d'entretien

Cisco

Cisco USC 5030 Manuel utilisateur

Cisco

Cisco NCS 6000 Manuel utilisateur

Cisco

Cisco ONS 15454 Manuel utilisateur

Cisco

Cisco NCS 4000 Series Manuel

Cisco

Cisco NCS 1004 Manuel

Cisco

Cisco Remote PHY Shelf 7200 Mode d’emploi

Cisco

Cisco Firepower 4100 Series Manuel utilisateur

Cisco

Cisco Nexus 7018 Manuel utilisateur

Cisco

Cisco TelePresence Server 7010 Mode d’emploi

Cisco

Cisco UCS 5108 Manuel utilisateur

Cisco

Cisco NCS 4009 Mode d’emploi

Manuels Châssis populaires d'autres marques

Advantech

Advantech IPC-623 Series Manuel utilisateur

IMC Networks

IMC Networks iMcV/18 Manuel utilisateur

Chenbro

Chenbro RB13804N4WFT Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR665 V3 Manuel utilisateur

Wuntronic

Wuntronic PCI4DRQ Manuel utilisateur

EtherWAN

EtherWAN EMC400 Manuel utilisateur

Overland Storage

Overland Storage SnapSAN S1000 Mode d’emploi

Philips

Philips LC4.1E A Manuel utilisateur

Supermicro

Supermicro SCF418 Series Manuel utilisateur

Chenbro

Chenbro RM437 Series Manuel utilisateur

Pickering

Pickering 40-914 Manuel utilisateur

HP A7503-S Instructions de montage

Supermicro

Supermicro SC823MTQ-R700LPB Manuel utilisateur

SilverStone

SilverStone RMS08 Series Manuel utilisateur

NI cRIO-FRC II Manuel utilisateur

Pickering

Pickering 65-200 Manuel utilisateur

Allied Telesis

Allied Telesis AT-MMCR18 Manuel utilisateur

Hisense

Hisense MSD6586 Manuel utilisateur