Canon Laser Shot LBP-1120 Manuel utilisateur
LASER SHOT LBP-1120
Getting Started Guide
Read this manual carefully before using your printer.
Save this manual for future reference.
This manual describes the instructions to get
your printer ready for use.
Contents
Step1 Unpacking and Setting Up the Printer .................. 2
Checking the Package Contents ........................................ 2
Step2 Installing the EP-22 Cartridge................................ 3
Step3 Connecting to the Power Supply ........................... 5
Step4 Connecting the Printer to Your Computer ............ 5
Step5 Setting the Paper Supports and Loading Paper .. 6
Setting the Paper Supports ................................................ 6
Selecting Paper Delivery .................................................... 6
Loading Paper .................................................................... 7
Step6 Installing the Software ............................................ 8
Installing the CAPT (Plug & Play) ....................................... 8
Appendix ............................................................................ 15
Using the Canon LASER SHOT LBP-1120 CD-ROM ...... 15
CD-ROM
CD-ROM
Manuals for the Printer
Getting Started Guide (This document)
User's Guide
Instructions for printing, regular maintenance, and troubleshooting
CD-ROM
Guides with this symbol are PDF-manuals included on the
attached CD-ROM.
(Refer to "Using the Canon LASER SHOT LBP-1120 CD-ROM,"
on p.15 in this manual before you use the CD-ROM.)
1
Preface
Conventions
The following symbols are used in this manual to explain procedures,
restrictions, handling precautions, and instructions that should be observed
for safety.
CAUTION
Indicates a caution concerning operations that may lead to injury to persons
or damage to property if not performed correctly. In order to use the printer
safely, always pay attention to these cautions.
IMPORTANT
Indicates operational requirements and restrictions. Be sure to read these
items carefully in order to operate the printer correctly, and to avoid damage
to the printer.
NOTE
Indicates a clarification of an operation, or contains additional explanations
for a procedure. Reading these notes is highly recommended.
Copyright 2002 by Canon Inc. All rights reserved.
No part of this publication may be reproduced or transmitted in any form or
by any means, electronic or mechanical, including photocopying and
recording, or by any information storage or retrieval system without the prior
written permission of Canon Inc.
Notice
Canon makes no guarantees of any kind with regard to this manual. Canon
shall not be held liable for errors contained herein or for consequential or
incidental damages incurred as a result of acting on information contained in
the manual.
Trademarks
LBP, Canon, LASER SHOT, and the Canon Logo are trademarks of Canon Inc.
Microsoft®, Windows®, Windows logo, and MS-DOS are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or in
other countries.
Other product or company names herein may be the trademarks of their respective
owners.
Location
Printer Location Requirements
Observe the following power requirements when you use the printer:
100 - 127 V (±10%) 50/60 Hz (±2 Hz)
220 - 240 V (±10%) 50 Hz (±2 Hz)
This printer's energy consumption is no more than 736 W for 100 - 127 V model
(634 W for 220 - 240 V model). Install the printer in a place where there is an
individual power outlet that can provide an adequate power supply.
Observe the following environmental requirements when you use the printer:
Temperature: 10°C - 32.5°C (50°F - 90.5°F)
Relative humidity: 20 - 80% RH with no condensation
The dimensions of the printer are as follows. When selecting the site for the printer,
the location should provide ample space for the printer as illustrated below.
Front Legal-size paper
(for Face-up delivery)
A4-size paper
(for Face-up delivery)
Dimensions Space required for installation
Top view
Side view
240mm
372mm
442mm
362mm
763 mm
60 mm
60 mm
356 mm
297 mm
100 mm
362 mm
482 mm
307 mm
763 mm
372 mm
240 mm
640 mm
100 mm
2
Unpacking and Setting
Up the Printer
Checking the Package Contents
Before installing the printer, make sure that the following items have
been enclosed. If all the items are not enclosed, or something is
broken, contact the place of purchase.
Carrying the Printer
Be sure to use both hands to hold the printer securely as illustrated below
when you carry it.
CAUTION
Do not carry the printer by holding the front cover, the face-up delivery slot,
or by holding it at the front and rear. This could result in damage to the
printer or personal injury if the printer is dropped.
Front cover Face-up
delivery slot
IMPORTANT
If the room temperature rises abruptly, or the printer is moved from a cool
and dry place to a warm and humid place, condensation may form inside the
printer and cause problems with paper delivery or a deterioration in print
quality and, in some cases, result in printer error. To prevent this, allow the
printer to sit for an hour or more to adjust to the new temperature.
NOTE
For ultrasonic humidifier users
If you use top water or well water in an ultrasonic humidifier, the impurities in
the water will be released into the air, and could get into the printer, reducing
the print quality. If you use an ultrasonic humidifier, use distilled water.
System Requirements
Before installing the printing software (CAPT), make sure your computer has the
following minimum configuration:
•Pentium PC running Windows 98/Me or Windows 2000/XP. Pentium 150 MHz or
higher processor running Windows 98/Me. Pentium 233 MHz or higher processor
running Windows 2000/XP. A Pentium 600 MHz or higher is recommended.
•32 MB of RAM for Windows 98/Me (48 MB for Windows 2000, 64 MB for Windows
XP) and 15 MB of available disk space for Windows 98/Me (10 MB for Windows
2000/XP). 64 MB of RAM for Windows 98/Me (128 MB for Windows 2000, 256 MB
for Windows XP) is recommended.
•Monitor with a resolution of 640 x 480, showing at least 16 colors.
•A standard USB port and a CD-ROM drive.
•Sound card (if you want to hear audio messages).
STEP1
3
Package Contents
MPower code
(Example: 120 V Model)
MOutput paper support
MGetting started guide
(This document)
MEP-22 cartridge MInput paper support
MCD-ROM
[User Software for LBP-1120]
•CAPT (Canon Advanced Printing
Technology) software
•USB driver
•User’s guide
•Getting started guide
MLBP-1120 printer
NOTE
An interface cable is not bundled with the printer. You need to buy one
separately that connects to your computer.
Installing the EP-22
Cartridge
For detailed information on handling toner cartridges, refer to the
User's
Guide
.
1
Remove the cartridge from its protective bag.
IMPORTANT
Save the protective bag. You may need to repack and transport the cartridge
at a later date.
2
Gently rock the cartridge from side to side five or six times to evenly distribute
the toner inside the cartridge.
STEP2
4
3
Place the cartridge on a sturdy surface. Snap the tab at the end of the cartridge
backwards and fold it back and forth until it is loose. Then pull the sealing
tape in the direction indicated in the illustration below.
Pull in this direction Pull within this angle
Sealing tape
CAUTION
If you get loose toner powder on your hands or clothing, wash it off with cold
water immediately. Using warm water may fix the toner to your hands or
clothing, making it difficult to remove.
4
Open the front cover.
5
Insert the cartridge into the printer along the guides. Make sure that the
cartridge slides all the way inside the printer.
6
Close the front cover.
5
Connecting to the Power
Supply
CAUTION
Before inserting the plug, make sure that the rating indicated on the printer
matches the voltage of the AC outlet.
1
Plug the power cord into the power socket.
2
Connect the other end of the power cord to the AC outlet.
3
Turn on the printer by pressing the "I" mark. (Turn off the printer by pressing
the "O" mark.)
NOTE
If the power does not turn on even when the printer is plugged into an AC
outlet, check the following items:
•Close the front cover if open.
•Make sure that the EP-22 cartridge is installed.
•If the EP-22 cartridge is already installed, remove and reinstall it.
•To reset the printer, turn off the power using the power switch, and unplug
the power cord. Wait two seconds or more, then connect the printer to the
AC outlet again.
STEP3
NOTE
Do not connect/disconnect a USB cable in the following states:
•The printer driver is being installed.
•The starting period of Windows after turning on a computer.
•The printer is performing a printing action.
You can connect/disconnect a USB cable even when the computer or the
printer is turned on. However, if the cable is connected/disconnected in
the states shown above, the computer and the printer may not function
properly.
•Connect/disconnect a USB cable at least five seconds after it was
disconnected/connected. When the computer or the printer is turned on,
be sure to connect/disconnect a USB cable at least five seconds after it
was disconnected/connected. If you connect/disconnect a cable soon after
it was disconnected/connected, the printer may not function properly.
CAUTION
Do not touch the metal surface of a USB plug when connecting/
disconnecting a USB cable. It may cause electrical shock.
1
Connect the square shape plug of the USB cable to the USB interface at the
rear of the printer.
Connecting the Printer
to Your Computer
STEP4
6
2
Connect the flat shape plug of the USB cable to the USB port of the computer.
NOTE
A dialog box to start the installation of the USB driver may appear when
connecting a USB cable to your computer in the state the printer is turned
on. For detailed information, refer to "Installing the CAPT (Plug & Play)," on
p. 8.
3
Turn on the printer by pressing the "I" mark.
Setting the Paper
Supports and Loading
Paper
Setting the Paper Supports
Insert the paper supports firmly into the slots at the front and back of
the printer. The slots have guides to ensure the correct support is in the
correct slot.
Slot guide
IMPORTANT
Supports should curve slightly towards the rear of the printer. Do not insert a
support so that it curves towards the front of the printer, or do not insert a
support into a wrong size slot forcibly.
Selecting Paper Delivery
Use face-up delivery for Legal-size plain paper, transparencies, and
label sheets as well as envelopes and postcards. Printouts come out
from the face-up delivery slot with the printed side face up.
You can use the face-up and face-down delivery for plain paper.
STEP5
7
Use the paper delivery selector to choose face-up or face-down
delivery.
Paper delivery selector
Face-down
Face-up
Loading Paper
There are two delivery trays on the top part of this printer, a multi-
purpose tray and a manual feed slot. It is possible to load up to
approximately 125 sheets of 64 g/m2plain paper into the multi-purpose
tray. The manual feed slot allows you to load manually one sheet at a
time. For detailed information on what type of paper you can use, refer
to the
User's Guide
.
Multi-purpose tray
Manual feed slot
IMPORTANT
To print letterhead paper or paper with a logo on it, insert the stack of paper
into the tray with the printing side face towards you so that the top edge of
the paper stack is inserted first into the printer.
NOTE
To print envelopes and postcards, refer to the
User's Guide
.
Loading Paper into the Multi-Purpose Tray
The multi-purpose tray can hold up to approximately 125 sheets of 64 g/m2
paper for high-volume printing. You can load Letter, Legal, A4, Executive,
B5-size of plain paper into the multi-purpose tray. Heavy paper,
transparencies, label sheets, postcards and envelopes are also acceptable.
Follow the steps below to load a stack of paper into the multi-purpose tray.
1
Fan the stack of paper well, then tap it on a flat surface to properly align the
edges.
2
Load the stack of paper into the multi-purpose tray.
3
Adjust the paper guides according to the size of the paper loaded.
Be sure to adjust the paper guides so that there is no space between each paper
guide and the edge of the stack of paper.
8
Loading Paper Manually
You can use the manual feed slot when you want to print the paper which is
a different size from the paper loaded into the multi-purpose tray,
transparencies, label sheets or postcards.
The manual feed slot allows you to load paper manually, one sheet at a time.
The manual feed always has priority over the multi-purpose tray.
1
Load paper into the manual feed slot, one sheet at a time.
2
Adjust the paper guides according to the size of the paper loaded.
Installing the Software
For Windows 98/Me users, see below.
For Windows 2000 users, see on p. 10.
For Windows XP users, see on p. 12.
Installing the CAPT (Plug & Play)
For Windows 98/Me
The screens shown in the instructions below are from Windows 98.
IMPORTANT
Before you install the software, make sure that the printer is connected to
your computer using a USB cable and the printer is turned on.
1
Turn on your computer, and then start Windows 98/Me. The USB port is
automatically detected. The [Add New Hardware Wizard] dialog box appears.
Click [Next].
STEP6
9
2
Select [Search for the best driver for your device (Recommended)] (for
Windows Me, select [Specify the location of the driver (Advanced)]), in the
[Add New Hardware Wizard] dialog box and click [Next].
3
Insert the User Software CD-ROM into the CD-ROM drive and check only
[Specify a location]. Then click [Browse] to select the driver in the language
that you want to install.
For example, if your CD-ROM drive is drive [D], browse to [D:\English\Win98] (for
Windows Me, [D:\English\WinMe]), and click [OK].
Confirm that the folder to browse is selected under [Specify a location], and click
[Next].
4
Click [Next]. Installation of the USB driver begins.
Click [Finish] when the USB driver has been installed.
5
The Add New Hardware Wizard (Canon LASER SHOT LBP-1120) appears
after the USB driver has been installed. Click [Next].
6
Repeat the procedure from step 2 to step 3.
Autres manuels pour Laser Shot LBP-1120
3
Table des matières
Autres manuels Canon Imprimante
Canon
Canon BJC-S330 Manuel
Canon
Canon PIXMA MG6460 Manuel utilisateur
Canon
Canon CX 350 Manuel utilisateur
Canon
Canon I450 - i 450 Color Inkjet Printer Manuel utilisateur
Canon
Canon iP90 - PIXMA Color Inkjet Printer Manuel d'installation
Canon
Canon PRO-300 Series Guide de configuration
Canon
Canon imageRUNNER ADVANCE C350 series Manuel utilisateur
Canon
Canon IPF600 Manuel utilisateur
Canon
Canon iPF8000S - imagePROGRAF Color Inkjet Printer Manuel utilisateur
Canon
Canon imageRUNNER ADVANCE DX C357iF Manuel utilisateur
Canon
Canon PIXMA MP970 Manuel utilisateur
Canon
Canon LASER CLASS 650i Instructions d'installation
Canon
Canon imageRUNNER ADVANCE DX 4700 Series Manuel utilisateur
Canon
Canon Color imageCLASS LBP7660Cdn Manuel utilisateur
Canon
Canon SELPHY CP760 Guide de configuration
Canon
Canon PIXMA iP7200 Series Manuel utilisateur
Canon
Canon BJC-S330 Manuel utilisateur
Canon
Canon imagePROGRAF iPF6400S Series Manuel utilisateur
Canon
Canon imagePRESS C7011VPS series Manuel utilisateur
Canon
Canon IMAGECLASS LBP654CDW Manuel utilisateur
Manuels Imprimante populaires d'autres marques
Ricoh
Ricoh Aficio AP400 Manuel utilisateur
BIXOLON
BIXOLON SRP-352plusV Manuel utilisateur
Epson
Epson Stylus Photo PX700W Instructions de montage
Ricoh
Ricoh SP204SF Manuel utilisateur
Star Micronics
Star Micronics futurePRNT TSP100 Manuel utilisateur
Epson
Epson TM-TM88V-i Manuel d'utilisation et d'entretien