Campbell 109 Manuel utilisateur

Revision: 05/2021

Campbell Scientific, Inc.

Table of contents

1. Introduction 1

2. Precautions 1

3. Initial inspection 1

4. QuickStart 1

5. Overview 4

6. Specifications 5

7. Installation 6

7.1 Wiring to data logger 6

7.2 Data logger programming 6

7.2.1 Therm109() instruction 7

7.3 Air temperature installation 7

7.4 Water temperature installation 9

7.5 Soil temperature installation 9

8. Operation 10

8.1 Sensor schematic 10

8.2 Measurement and output linearization 10

8.3 Electrically noisy environments 11

8.4 Long cable lengths 11

9. Troubleshooting and maintenance 12

9.1 Troubleshooting 12

9.2 Maintenance 12

9.3 Calibration 13

10. Attributions and references 13

Appendix A. Importing Short Cut code into CRBasic Editor 14

Appendix B. Example program 15

Appendix C. Thermistor resistance and temperature 16

Table of Contents - i

1. Introduction

The 109 Temperature Probe uses a thermistor to measure temperature in air, soil, and water. It

easily interfaces with most Campbell Scientific data loggers and can be used in a variety of

applications.

For Edlog data logger support, check the availability of an older manual at

www.campbellsci.com/old-manuals , or contact Campbell Scientific for assistance.

2. Precautions

READ AND UNDERSTAND the Safety section at the back of this manual.

Santoprene® rubber, which composes the black outer jacket of the 109 cable, will support

combustion in air. It is used because of its resistance to temperature extremes, moisture, and UV

degradation. It is rated as slow burning when tested according to U.L. 94 H.B. and passes

FMVSS302. However, local fire codes may preclude its use inside buildings.

3. Initial inspection

Check the packaging and contents of the shipment. If damage occurred during transport,

immediately file a claim with the carrier. Contact Campbell Scientific to facilitate repair or

replacement.

Check model information against the shipping documents to ensure the expected products and

the correct lengths of cable are received. Model numbers are found on each product. On cables

and cabled items, the model number is usually found at the connection end of the cable. Report

any shortages immediately to Campbell Scientific.

4. QuickStart

A video that describes data logger programming using Short Cut is available at:

www.campbellsci.com/videos/cr1000x-data logger-getting-started-program-part-3 . Short

109 Temperature Probe1

Cut is an easy way to program your data logger to measure the sensor and assign data logger

wiring terminals. Short Cut is available as a download on www.campbellsci.com . It is included

in installations of LoggerNet, RTDAQ, and PC400.

The following procedure also describes programming with Short Cut.

1. Open Short Cut and click Create New Program.

2. Double-click the data logger model.

3. In the Available Sensors and Devices box, type 109 or find the 109 in the Sensors >

Temperature folder. Double-click the 109 Temperature Probe. Data defaults to degree

Celsius. This can be changed by clicking the Deg C box and selecting Deg F, for degrees

Fahrenheit, or K for Kelvin.

109 Temperature Probe2

4. Click the Wiring tab to see how the sensor is to be wired to the data logger. Click OK after

wiring the sensor.

5. Repeat steps three and four for other sensors being measured. Click Next.

6. In Output Setup, type the scan rate, Data Output Storage Intervals, and meaningful table

names.

109 Temperature Probe3

7. Select the measurement and its associated output option.

8. Click Finish and save the program. Send the program to the data logger if the data logger

is connected to the computer.

9. If the sensor is connected to the data logger, check the output of the sensor in the data

display in LoggerNet, RTDAQ, or PC400 to make sure it is making reasonable

measurements.

5. Overview

The 109 is a rugged probe that accurately measures air, soil, or water temperature in a variety of

applications. The sensor consists of a thermistor encapsulated in an epoxy-filled aluminum

housing. This design allows the probe to be buried or submerged in water to 15m (50ft) or

21psi. When measuring air temperature, a six-plate radiation shield is normally used to mount

the 109 and limit solar radiation loading.

Features:

lMeasures air, soil, or water temperature

lCompatible with AM16/32-series multiplexers

lEasy to install or remove

lDurable

109 Temperature Probe4

lCompatible CRBasic data loggers: CR6, CR3000, CR1000X, CR800-series, CR300-series,

CR1000

6. Specifications

Sensor element: Measurement Specialties 100K3A1iA thermistor

Survival range: –50 to 100 °C

Measurement range: –50 to 70 °C

Time constant in air: 30 to 60 s in a wind speed of 5 m/s

Maximum cable length: 305 m (1000 ft)

Accuracy1

Worst case: ±0.60 °C (–50 to 70 °C)

±0.25 °C (–10 to 70 °C)

Interchangeability error: ±0.10 °C (0 to 70 °C)

±0.13 °C at –10 °C

±0.15 °C at –20 °C

±0.18 °C at –30 °C

±0.20 °C at –40 °C

±0.50 °C at –50 °C

Steinhart-Hart equation error: ≤ 0.03 °C (–50 to 70 °C)

Probe weight and dimensions 

Weight with 10 ft cable: 136 g (5 oz)

Length: 10.4 cm (4.1 in)

Diameter: 0.762 cm (0.3 in)

Compliance: View the EU Declaration of Conformity at

www.campbellsci.com/109

1Overall probe accuracy is a combination of thermistor interchangeability, bridge-resistor accuracy, and error of the

Steinhart-Hart equation. Bridge resistors have 0.1% tolerance with a 10 ppm temperature coefficient.

Interchangeability is the principle component error. If needed, an estimate of the interchangeability error for 0 to

50°C, that can be used as the Offset parameter of the Therm109() instruction, can be determined with a 1-point

or 2-point calibration.

109 Temperature Probe5

7. Installation

If you are programming your data logger with Short Cut, skip Wiring to data logger (p. 6) and

Data logger programming (p. 6). Short Cut does this work for you. See QuickStart (p. 1) for a Short

Cut tutorial.

7.1 Wiring to data logger

Table 7-1: Wire color, function, and data logger connection

Wire color Wire function Data logger connection terminal

Black Voltage-excitationinput U configured for voltage excitation1,

EX, VX (voltage excitation)

Red Analog-voltageoutput U configured for single-ended analog input1,

SE (single-ended, analog-voltage input)

Purple Bridge-resistor ⏚ (analog ground)

Clear EMF shield ⏚ (analog ground)

1U terminals are automatically configured by the measurement instruction.

7.2 Data logger programming

Short Cut is the best source for up-to-date data logger programming code.

If your data acquisition requirements are simple, you can probably create and maintain a data

logger program exclusively with Short Cut. If your data acquisition needs are more complex, the

files that Short Cut creates are a great source for programming code to start a new program or

add to an existing custom program.

NOTE:

Short Cut cannot edit programs after they are imported and edited in CRBasic Editor.

A Short Cut tutorial is available in QuickStart (p. 1). If you wish to import Short Cut code into

CRBasic Editor to create or add to a customized program, follow the procedure in Importing

Short Cut code into CRBasic Editor (p. 14). Programming basics are provided in the following

section. A complete program example can be found in Example program (p. 15).

109 Temperature Probe6

If the 109 probe is to be used with long cable lengths or in electrically noisy environments,

consider employing the measurement programming techniques outlined in Electrically noisy

environments (p. 11) and Long cable lengths (p. 11).

Details of 109 probe measurement and linearization of the thermistor output are provided in

Measurement and output linearization (p. 10).

7.2.1 Therm109() instruction

The Therm109() measurement instruction programs CRBasic data loggers to measure this

sensor. It applies a precise excitation voltage, makes a half-bridge resistance measurement, and

converts the result to temperature using the Steinhart-Hart equation. See Measurement and

output linearization (p. 10) for more information. Therm109() instruction and parameters are as

follows:

Therm109(Dest, Reps, SEChan, VxChan, SettlingTime, Integ/fN1, Mult, Offset)



Variations:

lTemperature reported as °C — set Mult to 1 and Offset to 0

lTemperature reported as °F — set Mult to 1.8 and Offset to 32

lAC mains noise filtering — set Integ/fN1 to the 60 Hz or 50 Hz option (see Electrically

noisy environments (p. 11))

lCompensate for long cable lengths — Set SettlingTime to 20000 (see Long cable

lengths (p. 11))

7.3 Air temperature installation

For air temperature measurements, locate probes over an open, level area at least 9 m (EPA;

Attributions and references (p. 13)) in diameter. The surface should be covered by short grass or

the natural earth surface where grass does not grow. Probes should be located at a distance of at

least four times the height of any nearby obstruction, and at least 30m (EPA) from large paved

areas. Sensors should be protected from thermal radiation, and adequately ventilated.

Standard air temperature measurement heights:

l1.25 to 2.0 m (WMO; Attributions and references (p. 13))

l2.0 m (EPA; Attributions and references (p. 13))

l2.0 m and 10.0 m for temperature difference (EPA)

109 Temperature Probe7

When exposed to sunlight, the 109 should be housed in a six-plate solar radiation shield. Six-

plate shields offered by Campbell Scientific are models 41303-5A, 41303-5B, or RAD06.

The white color of these shields reflects solar radiation, and the louvered construction allows air

to pass freely through, thereby keeping the probe at or near ambient temperature. The RAD06

uses a double-louvered design that offers improved sensor protection from insect intrusion and

driving rain and snow. In addition, the RAD06 shield has lower self-heating in bright sunlight

combined with higher temperatures (> 24 °C (75 °F)) and low wind speeds (< 2 m/s (4.5 mph)),

giving a better measurement.

The 41303-5A and RAD06 attach to a crossarm, mast, or user-supplied pipe with a 2.5 to 5.3cm

(1.0 to 2.1in) outer diameter. The 41303-5B attaches to a CM500-series pole or a user-supplied

pole with a 5.1cm (2.4in) outer diameter.

Tools required for installing a radiation shield to a tripod or tower include:

l1/2-inch open end wrench

lUV resistant cable ties

ladjustable wrench with a minimum 1-1/2 inch jaw size

FIGURE 7-1. Installing a 109 and 41303-5A Radiation Shield on a CM200-Series Crossarm

109 Temperature Probe8

Autres manuels pour 109

Table des matières

Autres manuels Campbell Instrument de mesure

Campbell

Campbell IRGASON Manuel utilisateur

Campbell

Campbell SkyVUE 8M Manuel utilisateur

Campbell

Campbell CR850 Manuel utilisateur

Campbell

Campbell CS650 Manuel utilisateur

Campbell

Campbell CS135 Manuel utilisateur

Campbell

Campbell ARG100 Manuel utilisateur

Campbell

Campbell CS650 Manuel utilisateur

Campbell

Campbell CR9000X Manuel utilisateur

Campbell

Campbell CMP3 Manuel utilisateur

Campbell

Campbell 03002 R.M Manuel utilisateur

Campbell

Campbell SI-111 Manuel utilisateur

Campbell

Campbell CS500-LC Manuel utilisateur

Campbell

Campbell SR20-D2 Manuel utilisateur

Campbell

Campbell CS300 Manuel utilisateur

Campbell

Campbell CPEC300 Manuel utilisateur

Campbell

Campbell Open Path Eddy Covariance System Manuel utilisateur

Campbell

Campbell HMP45C212 Manuel utilisateur

Campbell

Campbell Wind Monitor Series Manuel utilisateur

Campbell

Campbell CS300 Manuel utilisateur

Campbell

Campbell SN500SS Manuel utilisateur

Campbell

Campbell 247 Manuel utilisateur

Campbell

Campbell CNR4 Manuel utilisateur

Campbell

Campbell Weatherpak M Manuel utilisateur

Campbell

Campbell LI200X Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur