Burkert 2030 Manuel utilisateur
Quickstart
English Deutsch Français
Type 2030, 2031, 2031 K, 2032, 2033, 2037
Piston operated diaphragm valve,
Actuator sizes 175 and 225 mm, Diameter DN65 - DN100
Kolbengesteuerte Membranventile,
Antriebsgrößen 175 und 225 mm, Nennweiten DN65 - DN100
Vannes à membrane commandée par piston, Tailles
de mécanisme 175 et 225 mm, Piston section nominale DN65 - DN100
We reserve the right to make technical changes without notice.
Technische Änderungen vorbehalten.
Sous réserve de modifications techniques.
© Bürkert Werke GmbH & Co. KG, 201 - 2017
Operating Instructions 1706/0_EU-EN_008 / Original DE
3
Quickstart
1 QUICKSTART ..................................................................................................3
2 SYMBOLS .........................................................................................................3
3 INTENDED USE .............................................................................................4
4 BASIC SAFETY INSTRUCTIONS ..........................................................4
5 CONTACT ADDRESSES ...........................................................................5
6 TECHNICAL DATA ........................................................................................5
7 ASSEMBLY .......................................................................................................8
8 TRANSPORTATION, STORAGE, DISPOSAL ................................13
2 SYMBOLS
Warning to prevent death or serious injuries:
DANGER!
Warns of an immediate danger!
WARNING!
Warns of a potentially dangerous situation!
Warning to prevent moderate or minor injuries:
CAUTION!
Warns of a possible danger!
NOTE!
Warns of material damage!
Important tips and recommendations.
Refers to information in these operating instructions or in
other documentation.
▶designates instructions for risk prevention.
→designates a procedure which you must carry out.
1 QUICKSTART
The quickstart comprises important information.
▶Carefully read the quickstart and observe any safety information.
▶The quickstart must be available to every user.
▶The liability and warranty for types 2030, 2031, 2031 K, 2032, 2033
and 2037 do not apply if the quickstart instructions are not observed.
The quickstart illustrates the installation and commissioning of the
equipment with examples. A detailed description of the device can
be found in the operating instructions for types 2030, 2031, 2031 K,
2032, 2033 and 2037 in the internet at: www.burkert.com
If you have any queries, please contact your Bürkert sales
office.
english
Type 2030, 2031, 2031 K, 2032,
2033, 2037
4
Intended Use
3 INTENDED USE
Incorrect use of the Type 2030, 2031, 2031 K, 2032, 2033 and
2037 can be dangerous to people, nearby equipment and the
environment.
The diaphragm valve of Type 2030 is designed for the control of
contaminated and aggressive media. The valves of types 2031,
2031 K, 2032, 2033 and 2037 can also be used with ultrapure or
sterile media with higher viscosity.
▶In the potentially explosion-risk area the type 2030, 2031, 2031
K, 2032, 2033 and 2037 may be used only according to the
specification on the separate Ex type label. For use observe the
additional information enclosed with the device together with
safety instructions for the explosion-risk area.
▶Devices without a separate Ex type label may not be used in a
potentially explosive area.
▶Observe the permitted usage conditions for the equipment.
▶Only operate when in perfect condition and always ensure
proper storage, transportation, installation and operation.
▶Secure system/equipment against unintentional activation.
▶Only feed fluids into the media connections that are specified in
section „6 Technical Data“.
▶Do not make any internal or external changes to types 2030, 2031,
2031 K, 2032, 2033 and 2037. Secure equipment/device against
unintentional actuation.
▶Only trained technicians may perform installation and maintenance
work.
▶After an interruption in the power supply, ensure that the process
is restarted in a controlled manner.
▶Do not subject the body to mechanical loading.
▶Observe the general accepted technical rules.
3.2 Restrictions
If exporting the system/device, observe any existing restrictions.
4 BASIC SAFETY INSTRUCTIONS
These safety instructions do not make allowance for any
• contingencies and events which may arise during the installation,
operation and maintenance of the devices.
• local safety regulations – the operator is responsible for observing
these regulations, also with reference to the installation personnel.
Danger – high pressure!
▶Turn off the pressure and vent the lines before loosening lines or
valves.
Risk of electric shock!
▶Before reaching into the device or the equipment, switch off and
lock the power supply to prevent reactivation!
▶Observe applicable accident prevention and safety regulations
for electrical equipment!
Risk of burns!
The surface of the equipment can become hot during continuous
operation.
▶Do not touch the device with bare hands.
Danger of bursting from overpressure!
▶Observe the specifications on the type label for max. control and
medium pressure as well as the permitted medium temperature.
To prevent injuries/damage:
▶Secure system/equipment from unintentional activation.
english
Type 2030, 2031, 2031 K, 2032,
2033, 2037
5
Contact addresses
5 CONTACT ADDRESSES
Germany
Bürkert Fluid Control Systems
Sales Center
Christian-Bürkert-Str. 13-17
D-74653 Ingelfingen
Germany
Tel. + 49 (0) 7940 - 10 91 111
Fax + 49 (0) 7940 - 10 91 448
Email: [email protected]
International
Contact addresses can be found in the internet at: www.burkert.com
6 TECHNICAL DATA
6.1 Conformity
The types 2030, 2031, 2032, 2033 and 2037 are compliant with the
EC Directives according to the EC Declaration of Conformity.
6.2 Standards
The applied standards which are used to demonstrate compliance with
the EC Directives are listed in the EC type test certificate and/or the
EC Declaration of Conformity.
6.3 General technical data
Control medium: neutral gases, air
Flow media: Type 2030 contaminated, aggressive media;
Type 2031, 2032 and 2037 contaminated,
aggressive, ultrapure, sterile media and media
with higher viscosity
Installation position: any position, preferably with the actuator face
up;
tank bottom valve type 2033: actuator facing
downwards
Materials and connections see data sheet
english
Type 2030, 2031, 2031 K, 2032,
2033, 2037
6
Technical Data
6.4 Control functions (CF)
A
A
P
Closed by spring force in rest position
B
B
P
Opened by spring force in rest position
I
P
A
Actuating function via reciprocal pressurization
6.5 Type label
Type
Control function
Orifice (diaphragm size)
Body material
Identification number of the device
2030 A 65,0 EPDM PV
Made in Germany
00147838
W36LP
Pilot 4,5-6bar
FLNSCH Pmed 10bar
S/N 1060
Seal material
Port connection,
max. medium
pressure
Serial number
Control pressure
6.6 Labeling of forged body
Batch number/
manufacturing code
Company code
Material
Pressure level
Production/order
number (F-part)
Serial number
Code
Surface quality
Customized text
(optional)
Connection orifice
and pipe dimensions
6.7 Application conditions
WARNING!
Danger of bursting from overpressure!
If the device explodes, there is a risk of serious injuries, chemical
burns, scalding!
▶Do not exceed the maximum control and medium pressure.
Observe specifications on the type label!
▶Observe permitted ambient and media temperature.
Ambient temperature for actuators:
Material Size Temperature
PA 175 mm / 225 mm -10 ... +50 °C
Medium temperature for body:
Body material Temperature
Stainless steel -10 ... +140 °C
PVC (see PT graph) -10 ... +60 °C
PVDF (see PT graph) -10 ... +120 °C
PP (see PT graph) -10 ... +80 °C
Medium temperature for diaphragms:
Material Temperature Comments
EPDM / PTFE -10 ... +130 °C Steam sterilization up to
+150 °C
FKM -5 ... +130 °C
Dry up to +150 °C
otherwise only briefly up to
+150 °C
english
Type 2030, 2031, 2031 K, 2032,
2033, 2037
7
Technical Data
Maximum permitted medium pressure:
Permitted medium pressure depending on the medium temperature:
DN 65 - 100
10
8
6
4
2
20 40 60 80 100 120 140
PVC
PVDF
PP
Medium pressure [bar]
Medium temperature [°C]
Fig. 1: Graph of medium pressure / medium temperature
Permitted control pressure*:
Orifice
DN [mm] Actuator size
[mm] Min. control
pressure [bar] Max. control
pressure [bar]
65 175 2 6
80 175 2 6
80 225 2 6
100 225 2 6
* Observe the permitted pressure range according to the
type label!
Control pressure for control function A:
Orifice
DN [mm] Actuator size
[mm]
Control pressure [bar]
at medium pressure
0 bar maximum
65 175 64.5
80 175 65.0
80 225 65.0
100 225 65.0
Tab. 1: Control pressure CFA
The required minimum control pressure pmin for control function B
and I depends on the medium pressure.
For the pressure graphs see operating instructions on the
Internet at: www.burkert.com
english
Type 2030, 2031, 2031 K, 2032,
2033, 2037
8
Assembly
7 ASSEMBLY
7.1 Safety instructions
DANGER!
Danger – high pressure!
▶Turn off the pressure and vent the lines before loosening lines
or valves.
Risk of electric shock!
▶Before reaching into the device or the equipment, switch off the
power supply and lock to prevent reactivation!
▶Observe applicable accident prevention and safety regulations
for electrical equipment!
WARNING!
Risk of injury from incorrect installation!
▶Installation may only be performed by authorized technicians
with the appropriate tools!
Risk of injury from unintentional activation of the system and
uncontrolled restart!
▶Secure system against unintentional activation.
▶Following installation, ensure a controlled restart.
7.2 Before installation
• Before connecting the valve, ensure that the pipelines are aligned.
• The flow direction is optional.
7.2.1 Installation position general
Installation for self-drainage of the body
It is the responsibility of the installer and operator to ensure
self-drainage.
Installation for leakage detection
One of the bores (in the actuator base) for monitoring
leakage must be at the lowest point.
7.2.2 Installation position 2/2-way valve
• The piston-controlled diaphragm valve can be installed in any
position, preferably with the actuator face up.
To ensure self-drainage:
→Install body at an angle α = 10° to 40° to the horizontal
(see „Fig. 2“).
→Maintain an inclination of 1° – 5°.
There is a mark on forged and cast bodies, which must face
upwards (12 o’clock position, see „Fig. 3“).
→One of the bores (in the actuator base) for monitoring leakage,
must be at the lowest point.
english
Type 2030, 2031, 2031 K, 2032,
2033, 2037
9
Assembly
αAngle α: 10° to 40°
Inclination to the line axis 1° ... 5°
Fig. 2: Installation position for self-drainage of the body
Marking for self-draining
inclination
Fig. 3: Mark for correct installation position
7.2.3 Installation position T-valve type 2032
For the installation of the T-valves into circular pipelines, we recommend
the following installation positions:
For supply of a medium: For removal of a medium:
Fig. 4: Installation position of type 2032
7.2.4 Installation position Y-valve type 2037
For the installation of the Y-valves into systems, we recommend the
following installation positions:
For supply of a medium: For removal of a medium:
Fig. 5: Installation position of type 2037
english
Type 2030, 2031, 2031 K, 2032,
2033, 2037
10
Assembly
7.2.5 Installation of tank bottom valve
Type 2033
For information about tanks and welding instructions, refer to
the standard ASME VIII Division I.
We recommend that the valve is welded before the tank is
assembled. However, it is still possible to weld the valves to
completely installed tanks.
Before welding, make sure that:
• the tank bottom valve does not impact any other device installation
component and that is always remains possible to assemble and
dismantle the actuator.
• a minimum distance between 2 welding points of 3x the thickness
of the tank wall is maintained.
To ensure that the tank drains optimally, the valve should be
welded in the middle of the drain
The diameter of the holes in the tank and in the flange must be equal.
The valve has two weld edges to simplify welding and positioning of
the valve. The weld edges are about 3 mm long. If the tank wall is more
than 3 mm thick, the valve must be positioned on the „Fig. 6“.
→Grind the drain wall down,
→weld the valve in.
Position to be ground
on tank
Fig. 6: Position to be ground on tank
Before welding, check the batch number indicated on the
supplied manufacturer’s certificate 3.1.B.
Procedure:
→Position the flange into the hole so that the flange surface just
touches the drain surface.
→Fix 4 welding points and check the position of the valve.
→Weld on the valve to it projects evenly inside and outside the tank
while gas is supplied and using welding material compatible with
valve steel 316L (DIN 1.4435).
→Let the valves cool before grinding them smooth and polishing them
according to the applicable specifications.
These instructions are designed to assist in the installation of the tank
bottom valves and help avoid deformations and relaxations within the
tank.
Observe the laws applicable in the country with reference to
the qualification of welders and to welding procedures.
7.2.6 Preparatory work
→Clean pipelines (sealing material, swarf, etc.).
→Support and align pipelines.
Devices with welded body:
Before welding the body, the actuator and diaphragm must
be removed.
english
Type 2030, 2031, 2031 K, 2032,
2033, 2037
Autres manuels pour 2030
10
Ce manuel convient aux modèles suivants
5
Table des matières
Langues :
Autres manuels Burkert Unité de contrôle
Burkert
Burkert Type 2000 Manuel utilisateur
Burkert
Burkert 6211 EV Manuel utilisateur
Burkert
Burkert 3270 Manuel utilisateur
Burkert
Burkert 2100 series Manuel utilisateur
Burkert
Burkert 2060 Manuel utilisateur
Burkert
Burkert 5470 Manuel utilisateur
Burkert
Burkert 0312 Manuel utilisateur
Burkert
Burkert 3232 Manuel utilisateur
Burkert
Burkert 5406 Manuel utilisateur
Burkert
Burkert 2300 Series Manuel utilisateur
Burkert
Burkert 770 Manuel utilisateur
Burkert
Burkert 2503 Manuel utilisateur
Burkert
Burkert 2300 Series Manuel utilisateur
Burkert
Burkert 1066 Manuel utilisateur
Burkert
Burkert 8840 Manuel utilisateur
Burkert
Burkert 2006 Manuel utilisateur
Burkert
Burkert 2103 Series Manuel utilisateur
Burkert
Burkert 3323 Manuel utilisateur
Burkert
Burkert 0301 Manuel utilisateur
Burkert
Burkert 2933 Manuel utilisateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
