BOXLIGHT Mimio P12T Manuel utilisateur

P12T Touch-Interactive Projector Distance and Positioning Calculator

Introduction

This document provides distance calculation and positioning information for the P12 touch-interactive projector, enabling you to

determine the proper placement for the touch interactive WXGA, 16:9, and ultra-wide models of the P12 projector. It is essential

to reference the correct table for the projector model and measurement units (millimeters or inches) when placing the wall

bracket.

Note: This document is only for the touch-interactive models of the P12 projector. The distance calculation and positioning

information for the pen-interactive and non-interactive P12 models is on a separate document titled “P12 Pen-Interactive and

Non-Interactive Projector Positioning Guide.”

Projection Surface Flatness Requirement

The touch-interactivity feature requires a laser-ﬂat projection surface with a non-planarity speciﬁcation of ±0.12” (±3mm). Using a

projection surface that does not comply with this requirement will produce unsatisfactory or unreliable tracking performance.

It is very strongly recommended that the Laser Curtain Module be placed on the projection surface itself so as assure co-

planarity.

Frameless Versus Framed Whiteboards

The touch-interactive feature uses an infrared camera embedded in the projector to detect reﬂected infrared light generated by

the Laser Curtain Module. False positives caused by reﬂections from a frame surrounding the projection surface or environmental

sources of infrared can cause performance degradation.

If a framed whiteboard is used, the image must be positioned away from the frame at the distances shown in the diagram below.

A frameless whiteboard is recommended as it does not have this requirement.

Background

It is essential that the top of the projected image be positioned below the Tracking Buer

space as shown at right.

• 0.8” (20mm) for WXGA/HD

• 1.6” (40mm) for the ultra-wide 16:6

Positioning the top of the projected image starts with positioning the wall mount bracket.

The wall mount bracket will produce an image of the desired size when the top of the wall

plate is positioned at a distance “O” as on the diagram below (outlined in red dashes).

Figure 1

Positioning the Wall Bracket

The wall bracket must be positioned horizontally as shown on the diagram at right. The left edge of

the wall bracket must be 0.5” (13mm) to the right of the intended image center. If the wall bracket is

instead centered on the whiteboard, which initially seems the likely placement, the displayed image

will not be centered and proper alignment will not be possible.

Vertical positioning of the wall bracket should be determined from the relevant table below based on

the intended image size and aspect ratio.

Mounting Arms

The 27” (697mm) WallMount-P12W is the model bundled with the WXGA and 16:9 models.

The longer 33” (841mm) WallMount-P12U is the model bundled with the P12 ultra-wide model.

Example One

To produce the largest possible diagonal image at 16:10 aspect ratio on a frameless whiteboard:

• Measure the width and height of the projection surface. In this example, the measured width is 80” and the height 48”.

o Deduct 2” for the Laser Curtain Module + 0.8” for the Tracking Buer = 2.8”.

o The available height is 48” – 2.8” = 45.2”.

o The WXGA table below shows that a 45.2” height will

allow a diagonal size of 80”, which has a width of 72.1”

and leaves ≈9” of open space on the left and right.

• Determine the horizontal center of the intended image then

mark a point 0.5” (13mm) to the right of this. This mark deﬁnes

the horizontal position of the left edge of the wall bracket.

• From the WXGA table below – Distance “O” for the 85” image

is 13.5”.

• Mount the wall bracket so its top edge is that distance above

the top of where the projected image is to be positioned (which

is 2.8” below the top of the whiteboard’s projection surface).

• Attach the projector to the projector mounting bracket, leaving

the four bolts slightly loose so the projector can be adjusted

horizontally.

P12T Touch-Interactive Projector Distance and Positioning Calculator

Figure 2

Figure 3

• Attach the mounting arm with projector to the wall bracket. Leave the four bolts that secure the arm to the wall bracket

loose so the assembly can be adjusted vertically.

• The projector’s vertical position can be adjusted using the bolt (1/2”, 13mm) at the bottom of the bracket. Tighten the bolts

on the sides once the position is ﬁnalized.

• The projector can be adjusted horizontally ≈±1/2” (6mm) by sliding it within the projector mounting bracket. Tighten the

bolts once the position is ﬁnalized.

• Proceed to the alignment stage of the process below.

P12T Touch-Interactive Projector Distance and Positioning Calculator

Printed Monday, December 19, 2016 10:43

5

P12 Pen-Interactive and Non-Interactive Projector Positioning Tables

Diagonal

imagesize

(S)ininch

Imagewidth

(W)inin.

Imageheight

(H)inin.

Distance

fromsurface

of

whiteboard

tocenterof

projector

mount(T)in

in.

Distance

fromsurface

of

whiteboard

tobackof

projector(T1)

inin.

Distance

fromtopof

imagetotop

ofwallplate

(O)inin.

Distance

fromtopof

imagetotop

ofinterface

boss(O1)in

in.

Distance

fromtopof

imagetotop

ofprojector

(O2)inin.

85 72.1 45.0 14.6 9.2 13.5 10.5 9.7

86 72.9 45.6 14.8 9.4 13.5 10.6 9.8

87 73.8 46.1 15.0 9.6 13.6 10.6 9.8

88 74.6 46.7 15.2 9.8 13.7 10.7 10.0

89 75.5 47.2 15.5 10.1 13.8 10.8 10.0

90 76.3 47.7 15.7 10.3 13.9 10.9 10.1

91 77.2 48.2 15.9 10.5 14.0 11.0 10.2

92 78.0 48.8 16.1 10.7 14.1 11.1 10.3

93 78.9 49.3 16.4 11.0 14.2 11.2 10.4

94 79.7 49.8 16.6 11.2 14.3 11.3 10.5

95 80.6 50.4 16.8 11.4 14.4 11.4 10.6

96 81.4 50.9 17.0 11.7 14.5 11.5 10.7

97 82.2 51.4 17.3 11.9 14.6 11.6 10.8

98 83.1 51.9 17.5 12.1 14.7 11.7 10.9

99 83.9 52.5 17.7 12.3 14.8 11.8 11.0

100 84.8 53.0 18.0 12.6 14.8 11.9 11.1

101 85.6 53.5 18.1 12.8 15.0 12.0 11.2

102 86.5 54.1 18.4 13.0 15.0 12.0 11.3

103 87.4 54.6 18.6 13.2 15.1 12.1 11.3

104 88.2 55.1 18.9 13.5 15.2 12.2 11.5

105 89.1 55.7 19.1 13.7 15.3 12.3 11.5

106 89.9 56.2 19.3 13.9 15.4 12.4 11.7

107 90.7 56.7 19.5 14.1 15.5 12.5 11.7

108 91.6 57.2 19.7 14.3 15.6 12.6 11.8

109 92.4 57.8 20.0 14.6 15.7 12.7 11.9

110 93.3 58.3 20.2 14.8 15.8 12.8 12.0

111 94.1 58.8 20.4 15.0 15.9 12.9 12.1

112 95.0 59.4 20.6 15.2 16.0 13.0 12.2

113 95.8 59.9 20.9 15.5 16.1 13.1 12.3

114 96.7 60.4 21.1 15.7 16.2 13.2 12.4

115 97.5 60.9 21.3 15.9 16.3 13.3 12.5

P12WXGA(16:10)Wallmountinstallationmeasurementchart-inches

P12T Touch-Interactive Projector Distance and Positioning Calculator

Printed Monday, December 19, 2016 10:43

6

Diagonal

imagesize

(S)ininch

Imagewidth

(W)inin.

Imageheight

(H)inin.

Distance

fromsurface

of

whiteboard

tocenterof

projector

mount(T)in

in.

Distance

fromsurface

of

whiteboard

tobackof

projector(T1)

inin.

Distance

fromtopof

imagetotop

ofwallplate

(O)inin.

Distance

fromtopof

imagetotop

ofinterface

boss(O1)in

in.

Distance

fromtopof

imagetotop

ofprojector

(O2)inin.

87 75.8 42.6 14.6 9.2 14.3 11.3 10.6

88 76.7 43.1 14.8 9.4 14.4 11.5 10.7

89 77.6 43.6 15.0 9.6 14.6 11.6 10.8

90 78.4 44.1 15.2 9.8 14.6 11.7 10.9

91 79.3 44.6 15.5 10.1 14.8 11.8 11.0

92 80.2 45.1 15.7 10.3 14.8 11.9 11.1

93 81.1 45.6 15.9 10.5 15.0 12.0 11.2

94 81.9 46.1 16.1 10.7 15.1 12.1 11.3

95 82.8 46.6 16.3 10.9 15.2 12.2 11.4

96 83.7 47.1 16.6 11.2 15.3 12.3 11.5

97 84.5 47.6 16.8 11.4 15.4 12.4 11.6

98 85.4 48.0 17.0 11.6 15.5 12.5 11.7

99 86.3 48.5 17.2 11.8 15.6 12.6 11.8

100 87.2 49.0 17.4 12.0 15.7 12.7 11.9

101 88.0 49.5 17.6 12.2 15.8 12.8 12.0

102 88.9 50.0 17.9 12.5 15.9 12.9 12.1

P121080P(16:9)Wallmountinstallationmeasurementchart-inches

P12T Touch-Interactive Projector Distance and Positioning Calculator

Printed Monday, December 19, 2016 10:43

7

END

Diagonal

imagesize

(S)ininch

Imagewidth

(W)inin.

Imageheight

(H)inin.

Distance

fromsurface

of

whiteboard

tocenterof

projector

mount(T)in

in.

Distance

fromsurface

of

whiteboard

tobackof

projector(T1)

inin.

Distance

fromtopof

imagetotop

ofwallplate

(O)inin.

Distance

fromtopof

imagetotop

ofinterface

boss(O1)in

in.

Distance

fromtopof

imagetotop

ofprojector

(O2)inin.

120 112.4 42.1 23.8 18.4 18.2 15.2 14.4

121 113.3 42.5 24.0 18.6 18.3 15.3 14.5

122 114.2 42.8 24.3 18.9 18.4 15.4 14.6

123 115.2 43.2 24.5 19.1 18.5 15.5 14.7

124 116.1 43.5 24.7 19.3 18.6 15.6 14.8

125 117.0 43.9 25.0 19.6 18.7 15.7 15.0

126 118.0 44.3 25.2 19.8 18.8 15.8 15.0

127 118.9 44.6 25.4 20.0 18.9 15.9 15.2

128 119.8 44.9 25.7 20.3 19.1 16.1 15.3

129 120.8 45.3 25.9 20.5 19.1 16.1 15.4

130 121.7 45.6 26.1 20.7 19.3 16.3 15.5

131 122.6 46.0 26.4 21.0 19.4 16.4 15.6

132 123.6 46.3 26.6 21.2 19.4 16.5 15.7

133 124.5 46.7 26.9 21.5 19.6 16.6 15.8

134 125.5 47.0 27.1 21.7 19.7 16.7 15.9

135 126.4 47.4 27.3 21.9 19.8 16.8 16.0

136 127.3 47.8 27.6 22.2 19.9 16.9 16.1

137 128.3 48.1 27.8 22.4 20.0 17.0 16.2

138 129.2 48.5 28.0 22.6 20.1 17.1 16.3

139 130.2 48.8 28.3 22.9 20.2 17.2 16.4

140 131.1 49.2 28.5 23.1 20.3 17.3 16.5

P12UWHD(16:6)Wallmountinstallationmeasurementchart-inches

P12T Touch-Interactive Projector Distance and Positioning Calculator

1. Template must be printed at 100%.

2. Prior to printing, ensure that Page Scaling

is set to “None” on your print dialog box.

3. Measure the bar below. It must be exactly

3 inches long.

CONFIRM PRINTED PAPER SIZE

1 2 3 IN.0

P12T Touch-Interactive Projector Distance and Positioning Calculator

Wall Mount P12U and P12W Plate Template

P12T Touch-Interactive Projector Distance and Positioning Calculator

Caution

1. To ensure safety, please read this manual carefully before installation and follow the instructions herein. Store

this manual in a secure place for future reference.

2. The manufacturer shall not be responsible legally for any equipment damage or personal injury caused by

incorrect installation or operation not covered in this manual.

3. The wall mount is designed for easy installation and removal. The manufacturer shall not be liable for damage

to equipment or personnel injuries arising out of human factors or acts of God.

4. The projector hanger must be installed by professional personnel.

5. At least two persons are needed to install or remove the product in order to avoid any hazard caused by

falling objects.

6. Remember to maintain ample space around the projector to ensure suitable ventilation.

7. To ensure safety and avoid any accident, it is necessary to investigate the structure of the ceiling and select

an appropriate, durable location before installation.

8. The ceiling should have load-carrying capability to sustain more than four times the total weight of the

projector and the hanger. Also, make sure it has enough strength to withstand earthquakes and other

shocks.

9. Please carefully check the areas around where the hanger is to be installed:

• Avoid any places that have high temperatures, humidity, or are subject to contact with water.

• Do not install the product near air conditioning vents and avoid places where it is dusty or fumy.

• Only install on vertical walls and avoid slanted surfaces.

• Do not install in places subject to vibrations or shocks.

• Do not install in places subject to direct exposure to bright light, as it may cause eye fatigue when

viewing the display panel.

10. Do not modify any accessory or use broken parts. Contact local distributors if you have any questions.

11. Tighten all screws (do not exert force on any screw with excess torque to avoid breaking the screw or

damaging its thread).

12. The maximum weight of the projector that the hanger can support is below 15kg (33lbs).

13. Do not hang any other objects except the projector on this hanger. Hanging on this hanger by any personnel

is strictly prohibited.

14. Drill holes and screws will be left on the wall once the projector and hanger are removed. Stains may occur

after extended use.

15. Since the manufacturer has no way to control the wall type and installation of wall mount, the warranty of the

product shall only cover the body of the wall mount. The warranty period of the product is 5 years.

16. Please consult the English language manual for any dispute on conditions.

Autres manuels BOXLIGHT Projecteur

BOXLIGHT

BOXLIGHT S65EA Manuel utilisateur

BOXLIGHT

BOXLIGHT MP-56t Manuel utilisateur

BOXLIGHT

BOXLIGHT CP-18t Manuel utilisateur

BOXLIGHT

BOXLIGHT Seattle X35N Manuel utilisateur

BOXLIGHT

BOXLIGHT Cambridge X33N Manuel utilisateur

BOXLIGHT

BOXLIGHT TraveLight3 Manuel utilisateur

BOXLIGHT

BOXLIGHT 6000 Manuel utilisateur

BOXLIGHT

BOXLIGHT ProjectoWrite5 Manuel de programmation

BOXLIGHT

BOXLIGHT SP-48Z Manuel utilisateur

BOXLIGHT

BOXLIGHT XD-2m Manuel utilisateur

BOXLIGHT

BOXLIGHT Studio Experience Matinee 2HD Manuel utilisateur

BOXLIGHT

BOXLIGHT ProjectoWrite7 P7 WX32N Manuel utilisateur

BOXLIGHT

BOXLIGHT ProjectoWrite2 Manuel utilisateur

BOXLIGHT

BOXLIGHT CD-600m Manuel utilisateur

BOXLIGHT

BOXLIGHT MP-63E Manuel utilisateur

BOXLIGHT

BOXLIGHT XD-9m Manuel utilisateur

BOXLIGHT

BOXLIGHT CP-635i Manuel utilisateur

BOXLIGHT

BOXLIGHT 9000-INT Manuel utilisateur

BOXLIGHT

BOXLIGHT CP-12tA Manuel utilisateur

BOXLIGHT

BOXLIGHT CP-775i Manuel utilisateur

BOXLIGHT

BOXLIGHT CP-15t Manuel utilisateur

BOXLIGHT

BOXLIGHT MP-63E Manuel utilisateur

BOXLIGHT

BOXLIGHT BL WX25NU Manuel utilisateur

BOXLIGHT

BOXLIGHT Cinema 12SF Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

BOXLIGHT mimio P12T Manuel utilisateur

Manuels Projecteur populaires d'autres marques