Bosch TC2073 Manuel utilisateur

Instruction Manual

EN Indoor Wall and

Corner Housings

TC2073

EN |2

Bosch Security Systems | 09 August 2004

TC2073 | Instruction Manual | Important Safeguards

Important Safeguards

1. Read, Follow, and Retain Instructions - All safety

and operating instructions should be read and

followed before operating the unit. Retain instructions

for future reference.

2. Heed Warnings - Adhere to all warnings on the unit

and in the operating instructions.

3. Electrical Connections - Only a qualified electrician

should make electrical connections.

4. Cable Runs - All cable runs must be within

permissible distances.

5. Mounting - This unit must be properly and securely

mounted to a supporting structure capable of

sustaining the weight of the unit. Accordingly:

a. The installation should be made by a qualified

installer, in compliance with local codes.

b.Exercise care in selecting suitable hardware to

install the unit, taking into account both the

composition of the mounting surface and the

weight of the unit. Periodically examine the unit

and the supporting structure to ensure that the

integrity of the installation is intact.

Failure to comply with these stipulations may result in

separation from the support structure. This may cause

damages or injury to anyone or anything struck by the

falling unit.

6. Attachments - Attachments not recommended by

the product manufacturer should not be used, as they

may cause hazards.

Safety Precautions

Attention: Installation should be performed by

qualified service personnel only in accordance

with the National Electrical Code or applicable

local codes.

Power Disconnect. Units with or without

ON-OFF switches have power supplied to the

unit whenever the power cord is inserted into the

power source; however, the unit is operational

only when the ON-OFF switch is in the ON

position. The power cord is the main power

disconnect for all units.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

This symbol indicates the presence of

uninsulated “dangerous voltage” within the

product’s enclosure. This may constitute a

risk of electric shock.

The user should consult the operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

EN |3

Bosch Security Systems | 09 August 2004

TC2073 Series | Instruction Manual | Unpacking

1UNPACKING

This mechanical equipment should be unpacked and

handled carefully.

Check for the following items:

Qty. Item

1Model No. of unit

1Key (taped to the housing cover)

1Corner-mount housing

1Camera bracket

1Toolhead driver1for security fastener

1One tool per housing

If an item appears to have been damaged in shipment,

replace it properly in its carton and notify the shipper.

If any items are missing, notify your Bosch Security

Systems Inc. Sales Representative or Customer Service.

The shipping carton is the safest container in which the

unit may be transported. Save it for possible future use.

2SERVICE

If the unit ever needs repair service, the customer

should contact the nearest Bosch Security Systems, Inc.

Service Center for return authorization and shipping

instructions.

Service Centers

USA

Phone: 800-366-2283 or 717-735-6638

fax: 800-366-1329 or 717-735-6639

CCTV Spare Parts

Phone: 800-894-5215 or 408-956-3853 or 3854

fax: 408-957-3198

e-mail: [email protected].com

Canada

Phone: 514-738-2434

Europe, Middle East & Asia Pacific Region

Phone: 32-1-440-0711

For additional information, see

www.boschsecuritysystems.com.

3INSTALLATION

1. Remove the contents from the box.

2. Loosen the security fasteners using the toolhead

driver, and open the front half of the housing.

3. Remove the paper from the back side of the

window.

4. The Camera bracket can be mounted into the

housing in one of two ways, depending on camera

size and the desired angle (see FIGURE 1).

5. Place the housing in the corner and mark the

location of the four (4) mounting holes.

6. Pass the electrical and video cables through the

hole provided in the back of the housing.

7. Mount the housing by bolting it to the wall.

8. Make the electrical and camera connections.

USE 0NLY CLASS 2 POWER SUPPLY FOR

THE CAMERA.

9. Adjust the camera angle and tighten the camera

bracket. Loosen, but do not remove the nuts to

adjust the bracket.

10. Close the housing and tighten the security

fasteners.

FIGURE 1

3935 890 15912 04-33 | Updated August 09, 2004 | Data subject to change without notice.

Bosch Security Systems, Inc.

850 Greenfield Road

Lancaster, PA 17601 USA

Tel: 800-326-3270

Fax: 1-717-735-6560

www.boschsecuritysystems.com

Bosch Security Systems B.V.

P.O. Box 80002

5600 JB Eindhoven

The Netherlands

Tele +31 40 27 80000

Bosch Security Systems Pte Ltd.

38C Jalan Pemimpin

Singapore 577180

Republic of Singapore

Tel: 65 (6) 319 3486

Table des matières

Autres manuels Bosch Système de sécurité

Bosch

Bosch MAP 5000 Series Manuel utilisateur

Bosch

Bosch DIVAR DIP-7080-00N Manuel utilisateur

Bosch

Bosch D220 Manuel utilisateur

Bosch

Bosch MAP 5000 Manuel utilisateur

Bosch

Bosch ICP-CP508 Manuel utilisateur

Bosch

Bosch DS7400Xi Manuel utilisateur

Bosch

Bosch AMAX 2100 Manuel d'instructions

Bosch

Bosch ODU-FA Mode d’emploi

Bosch

Bosch Plena Power Amplifier Instructions de montage

Bosch

Bosch Solution 16plus Manuel utilisateur

Bosch

Bosch Security Systems Manuel utilisateur

Bosch

Bosch FMC-300RW-GSRRD Manuel utilisateur

Bosch

Bosch ICP-VR8488 Manuel utilisateur

Bosch

Bosch FMC-210-SM Manuel utilisateur

Bosch

Bosch AMAX panel 2000 ICP-AMAX-P Manuel utilisateur

Bosch

Bosch DS938Z Manuel utilisateur

Bosch

Bosch UEZ Manuel utilisateur

Bosch

Bosch LTC 1311/20 FlexiDome I Feuille d'instructions

Bosch

Bosch CM705B Comment utiliser

Bosch

Bosch LTC 9441 Series Manuel utilisateur

Bosch

Bosch D420 Manuel utilisateur

Bosch

Bosch FMC-210-DM-G-R Manuel utilisateur

Bosch

Bosch D222 Manuel utilisateur

Bosch

Bosch AMAX 2100 Manuel d'instructions

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur