Bosch AMC UL1 Manuel utilisateur

AMC UL1 Housing | en 1

Bosch Security Systems Assembly Instruction F.01U.024.980 | V.2 | 2006.08

Included Parts

The metal housing inlcudes the following components:

Figure 1 Parts of the housing

The accessories kit includes the following cables. Install these

cables as described in Section Connection of the Devices,

page 4.

2en | AMC UL1 Housing

F.01U.024.980 | V.2 | 2006.08 Assembly Instruction Bosch Security Systems

Figure 2 Accessories kit content

Content of the accessories kit:

A= Pre-assembled cable to connect the AMC to the power sup-

ply

B= Pre-assembled cable to connect the batteries to the UPS

(uninterruptable power supply) which is included in the power

supply

C= Cable using 24 V mode

D= Grounding cable for the cover

E= Cable ties to secure the pre-assembled cable

G= Pre-assembled cable with temperature sensor

H= Three screw anchors S8 and wood screws M6 x 50

J= Bracket for cable fixing

AMC UL1 Housing | en 3

Bosch Security Systems Assembly Instruction F.01U.024.980 | V.2 | 2006.08

Mounting the Housing

Open the housing cover lock with the provided key and remove

the hood from the wall mounted frame.

Mount the metal housing at the desired position with the screw

anchors provided with the enclosure.

Use the screws (position Hof the accessories kit) at the points

to mount the housing against the wall.

Figure 3 Demensions of the housing

4en | AMC UL1 Housing

F.01U.024.980 | V.2 | 2006.08 Assembly Instruction Bosch Security Systems

Connection of the Devices

Figure 4 Connection of the devices

AMC UL1 Housing | en 5

Bosch Security Systems Assembly Instruction F.01U.024.980 | V.2 | 2006.08

1. Mount the AMC on the rail (item 2in Figure 1) and left

aside the power supply.

2. Put the batteries on the bottom of the housing and secure

them beneath the battery clips (item 7 in Figure 1).

3. Stick the bracket J (Figure 2) on the back of the housing in

such a way that later on not used connectors of the cable

Bcan fixed with it.

4. Cable set A:

a. Connect the 7-pin plug A1 to the AMC’s power supply

connector (labeled: POWER).

b. Attach connectors A3 to the PS-interface DC and A2

to the interface labeled OK.

c. Connect the grounding cable A4 beneath the ground-

ing point 3.

5. Cable set B:

a. Connect the plug connector B1 the second position

from the left on the power supply - labeled with BAT.

b. Attach connector B2b (red) to the +-pin of the first

battery.

c. With cable Cconnect the --pin of the first battery to

the +-pin of the second battery.

d. Attach connector B2a (black) to the --pin of the sec-

ond battery.

e. Connectors B3a and B3b are not used.

6. Cable set G:

a. Attach connector G1 on the PS-interface labbeled

RTH.

NOTE!

The following steps describe connecting the batteries in 24 V

mode. For information on 12 V mode connections, refer to

Section 12 V Mode Variations, page 7.

6en | AMC UL1 Housing

F.01U.024.980 | V.2 | 2006.08 Assembly Instruction Bosch Security Systems

b. Route the cable across the temperature sensor

bracket 6so that the temperature sensor G2 hangs

approximitely 5 cm (2 in.) above the batteries.

7. Pre-assembled cable set 12:

a. Connect the 2-pin plug 13 on the interface AC of the

power supply.

8. Pre-assembled cable 5:

a. Connect the loose ends of the cover tamper switch to

the 2-pin screw connector on the top of the AMC.

Position the cable in the space between the housing

and the mounting rail.

9. Connect the main AC supply X:

a. Connect the brown (phase) wire to terminal L1.

b. Connect the blue (neutral) wire to terminal N.

c. Connect the grounding cable to the housing at posi-

tion 11.

DANGER!

Remove the fuse from the three-pin connector 12 before pro-

ceeding with the power supply connection.

Do not install the fuse before completing the installation proce-

dure.

CAUTION!

Shorten the external supply wires so that the ground (yellow/

green) wire is at least 20 mm (0.8 in.) longer than the live (blue

and brown) wires. This ensures that the ground wire cannot be

accidentally disconnected before life wires.

AMC UL1 Housing | en 7

Bosch Security Systems Assembly Instruction F.01U.024.980 | V.2 | 2006.08

10. Cable D:

If this cable is not pre-installed on grounding point 1, use

the cable Dfrom the accessories kit.

a. Connect D1 to grounding post 1.

b. Connect D2 to the grounding post on the cover.

11. Install the fuse.

12. Close the cover.

12 V Mode Variations

Figure 5.1 + 2 12 V mode with one and two batteries

NOTE!

Connect the readers and other peripheral devices as described

in the AMC Installation Manual (P/N: F01U.028.713). Route the

device cables through the knock-outs in the top an right side

wall of the housing, or through the rear of the housing.

8en | AMC UL1 Housing

F.01U.024.980 | V.2 | 2006.08 Assembly Instruction Bosch Security Systems

The 12 V mode can be configured using one or two batteries.

For a one-battery installation, refer to Figure 5.1, and perform

the following procedure:

1. Connect B1 to the power supply position labbeled BAT.

2. Connect B2a (black) to the battery’s -terminal, and B2b

(red) to the battery’s +terminal.

3. Connectors B3a and B3b remain unused - fix them with the

bracket J.

For the two-battery installation, refer to Figure 5.2, and perform

the following procedure:

1. Connect B1 to the power supply position labbeled BAT.

2. Connect B2a (black) to the battery’s - terminal, and B2b

(red) to the battery’s +terminal.

3. Connect B3a (black) to the second battery’s -terminal,

and B3b (red) to the second battery’s +terminal.

NOTE!

To switch the power supply between 12 V or 24 V modes, dis-

connect the input voltage and set the switch as shown in the

figure below.

Table des matières

Autres manuels Bosch Système de sécurité

Bosch

Bosch AMAX panel 4000 Manuel utilisateur

Bosch

Bosch DS484Q Manuel utilisateur

Bosch

Bosch DIVAR DIP-6080-00N Manuel utilisateur

Bosch

Bosch PRAESENSA Manuel utilisateur

Bosch

Bosch Solution 2000 Series Mode d'emploi

Bosch

Bosch DIP-7040-00N Manuel utilisateur

Bosch

Bosch ISW-BHB1-WX Manuel de service

Bosch

Bosch CM705B Comment utiliser

Bosch

Bosch Plena Power Amplifier Manuel utilisateur

Bosch

Bosch LTC 8540/00 Manuel utilisateur

Bosch

Bosch ICP-MAP5000-2 Manuel utilisateur

Bosch

Bosch DS7400Xi Manuel utilisateur

Bosch

Bosch D222TD Manuel utilisateur

Bosch

Bosch Solution 16i Manuel utilisateur

Bosch

Bosch Solution 144 Manuel utilisateur

Bosch

Bosch BE 300 LSN Manuel utilisateur

Bosch

Bosch Plena Power Amplifier Instructions de montage

Bosch

Bosch Solution 6000-IP Manuel utilisateur

Bosch

Bosch ITS-SPDIAL-FR Manuel utilisateur

Bosch

Bosch D222 Manuel utilisateur

Bosch

Bosch LBB 1968 Manuel utilisateur

Bosch

Bosch CP700B Comment utiliser

Bosch

Bosch SE3000 Series Manuel du produit

Bosch

Bosch CC610PB Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur