Black Box Sync/Async Fiber Optic Modem Manuel utilisateur

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

JUNE 2000

ME555A

ME555AE

ME556A

ME556AE

Sync/Async Fiber Optic Modem

FCC INFORMATION

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio frequency energy and if not

installed and used properly, that is, in strict accordance with the manufacturer’s

instructions, may cause interference to radio communication. It has been tested

and found to comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are designed to

provide reasonable protection against such interference when the equipment is

operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct the

interference.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from digital

apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique publié par Industrie Canada.

SYNC/ASYNC FIBER OPTIC MODEM

FCC REQUIREMENTS FOR

TELEPHONE-LINE EQUIPMENT

1. The Federal Communications Commission (FCC) has established rules which

permit this device to be directly connected to the telephone network with

standardized jacks. This equipment should not be used on party lines or coin

lines.

2. If this device is malfunctioning, it may also be causing harm to the telephone

network; this device should be disconnected until the source of the problem

can be determined and until the repair has been made. If this is not done, the

telephone company may temporarily disconnect service.

3. If you have problems with your telephone equipment after installing this

device, disconnect this device from the line to see if it is causing the problem

If it is, contact your supplier or an authorized agent.

4. The telephone company may make changes in its technical operations and

procedures. If any such changes affect the compatibility or use of this device,

the telephone company is required to give adequate notice of the changes.

5. If the telephone company requests information on what equipment is

connected to their lines, inform them of:

a. The telephone number that this unit is connected to.

b. The ringer equivalence number.

c. The USOC jack required: RJ-11C.

d. The FCC registration number.

Items (b) and (d) can be found on the unit’s FCC label. The ringer

equivalence number (REN) is used to determine how many devices can be

connected to your telephone line. In most areas, the sum of the RENs of all

devices on any one line should not exceed five (5). If too many devices are

attached, they may not ring properly.

6. In the event of an equipment malfunction, all repairs should be performed by

your supplier or an authorized agent. It is the responsibility of users requiring

service to report the need for service to the supplier or to an authorized

agent.

DOC STATEMENT

CERTIFICATION NOTICE FOR

EQUIPMENT USED IN CANADA

The Canadian Department of Communications label identifies certified

equipment. This certification means that the equipment meets certain

telecommunications-network protective, operation, and safety requirements. The

Department does not guarantee the equipment will operate to the user’s

satisfaction.

Before installing this equipment, users should ensure that it is permissible to be

connected to the facilities of the local telecommunications company. The

equipment must also be installed using an acceptable method of connection. In

some cases, the company’s inside wiring associated with a single-line individual

service may be extended by means of a certified connector assembly (extension

cord). The customer should be aware that compliance with the above conditions

may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian

maintenance facility—in this case, your supplier. Any repairs or alterations made

by the user to this equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user to disconnect the

equipment.

Users should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines, and internal metallic water pipe

system, if present, are connected together. This precaution may be particularly

important in rural areas.

CONFORMANCE

EN 55022 (1994): Limits and methods of measurement of radio disturbance

characteristics of information technology equipment.

EN 50082-1 (1992): Electromagnetic compatibility—Generic immunity standards

for residential, commercial, and light industry.

Safety: EN 60950 (1992/93): Safety of information technology equipment,

including electrical business equipment.

SYNC/ASYNC FIBER OPTIC MODEM

TELECOMMUNICATION SAFETY

The safety status of each of the ports on the Sync/Async Fiber Optic Modem is

declared according to EN 41003 and is detailed in the table below:

Safety Status Ports

SELV* RS-530

*SELV=Safety Extra-Low Voltage

LASER WARNINGS

This product may be equipped with a laser diode. The laser warning symbol will be

attached near the optical transmitter. Please observe the following precautions:

• Do not attempt to adjust the laser drive current.

• Do not use broken or unterminated fiber optic cables/connectors or stare at

the laser beam.

• The use of optical equipment with this product will increase eye hazard.

• Use of controls, adjustments, or performing procedures other than those

specified herein, may result in hazardous radiation exposure.

NOM STATEMENT

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de

que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca

de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que

sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe colocar

en libreros o gabinetes que impidan el flujo de aire por los orificios de

ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el aparato.

SYNC/ASYNC FIBER OPTIC MODEM

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización

del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen del

aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas

de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

TRADEMARKS

TRADEMARKS USED IN THIS MANUAL

AS/400®is a registered trademark of International Business Machines

Corporation.

ST®is a registered trademark of American Telephone and Telegraph Company.

Any other trademarks mentioned in this manual are acknowledged to be the

property of the trademark owners.

SYNC/ASYNC FIBER OPTIC MODEM

Contents

Quick Start Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.1.2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.1.3 Versions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.1.4 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.2 Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.2.1 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.2.2 Rear Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.3 Functional Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.3.2 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.3.3 Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.3.4 Async-to-Sync Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.3.5 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3. Installation and Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.2 Site Requirements and Prerequisites . . . . . . . . . . . . . . . . . . . . . 19

3.2.1 Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.2.2 Ambient Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.3 What the Package Includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.4 What You Need to Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.5 Jumper and Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.5.1 Strap Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.5.2 Connecting the Interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.5.3 Connecting the Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

4.2 Front-Panel Controls and Indicators. . . . . . . . . . . . . . . . . . . . . . 28

4.3 Initial Operation and Basic Checks. . . . . . . . . . . . . . . . . . . . . . . 30

4.3.1 Power-On Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4.3.2 Running Self-Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.4 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.4.1 Changing Field Strapping . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.4.2 Running Diagnostic Loops . . . . . . . . . . . . . . . . . . . . . . . . . 32

CONTENTS

4.4.3 Power-Off Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5. Troubleshooting and Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.2 Loopback Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.2.1 Local Test—Local Analog Loopback (LLB)

Standard V.54 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.2.2 Remote Digital Loopback (RLB) Standard V.54. . . . . . . . 35

5.2.3 Local Digital Loopback (DIG) Non-Standard . . . . . . . . . . 36

5.3 Internal BERT Circuit Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.3.1 Modem Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

5.3.2 Two-BERT Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

5.4 (Local) Analog Loopback Test . . . . . . . . . . . . . . . . . . . . . . . . . . 39

5.5 Communication Link Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.5.1 Remote Digital Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.5.2 Local Digital Loopback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Appendix A: DTE Interface Signal Assignments. . . . . . . . . . . . . . . . . 42

Appendix B: Connecting RS-530 to RS-422 . . . . . . . . . . . . . . . . . . . . . 45

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Black Box Modem

Black Box

Black Box MD1650A-JP Manuel utilisateur

Black Box

Black Box RM1600 Manuel utilisateur

Black Box

Black Box CSU/DSU MS/DBU Manuel utilisateur

Black Box

Black Box ME759C-RJ45 Manuel utilisateur

Black Box

Black Box MDS932AE-10BT Manuel utilisateur

Black Box

Black Box ME109A Manuel utilisateur

Black Box

Black Box Mini Driver 4W-S Manuel utilisateur

Black Box

Black Box ME0004C-G703 Manuel utilisateur

Black Box

Black Box ME738A-F Manuel utilisateur

Black Box

Black Box ME801A-E Manuel utilisateur

Black Box

Black Box MC119A Manuel utilisateur

Black Box

Black Box High Speed SHM-B Async Manuel utilisateur

Black Box

Black Box ME251A-R3 Manuel utilisateur

Black Box

Black Box MT240A-R2 Manuel utilisateur

Black Box

Black Box MT632A-ST35 Manuel utilisateur

Black Box

Black Box SHM-B Plus Async Series Manuel utilisateur

Black Box

Black Box ME621A Manuel utilisateur

Black Box

Black Box MDR100A-R5 Manuel utilisateur

Black Box

Black Box ME376A-R2 Manuel utilisateur

Black Box

Black Box MDS932C-1 Manuel utilisateur

Black Box

Black Box MDS932AE-10BT-R2 Manuel utilisateur

Black Box

Black Box Short-Haul Modem-FSK Manuel utilisateur

Black Box

Black Box 202T Manuel utilisateur

Black Box

Black Box LDM-MR 19.2 Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur