Black Box ME570A-MST Manuel utilisateur

1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S. 24 hours, 7 A.M. Monday to midnight Friday: 877-877-BBOX

FREE technical support, 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mail order: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

NOVEMBER 1999

ME570A-MST

ME570A-FST

ME570A-MSM

ME570A-FSM

ME570C-ST

ME570C-SM

Async/Sync Fiber Optic Modem

Async/Sync FO Modem Card

Async/Sync Fiber

Optic Modem

ASYNC/SYNC FIBER OPTIC MODEM AND FO MODEM CARD

FEDERAL COMMUNICATIONS COMMISSION

AND

INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio frequency energy and if not

installed and used properly, that is, in strict accordance with the manufacturer’s

instructions, may cause interference to radio communication. It has been tested

and found to comply with the limits for a Class A computing device in accordance

with the specifications in Subpart J of Part 15 of FCC rules, which are designed to

provide reasonable protection against such interference when the equipment is

operated in a commercial environment. Operation of this equipment in a

residential area is likely to cause interference, in which case the user at his own

expense will be required to take whatever measures may be necessary to correct

the interference.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emission from

digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique publié par Industrie Canada.

ASYNC/SYNC FIBER OPTIC MODEM AND FO MODEM CARD

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de

que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca

de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que

sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe colocar

en libreros o gabinetes que impidan el flujo de aire por los orificios de

ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

ASYNC/SYNC FIBER OPTIC MODEM AND FO MODEM CARD

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el aparato.

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización

del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen del

aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas

de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

ASYNC/SYNC FIBER OPTIC MODEM AND FO MODEM CARD

FCC REQUIREMENTS FOR

TELEPHONE-LINE EQUIPMENT

1. The Federal Communications Commission (FCC) has established rules

which permit this device to be directly connected to the telephone network

with standardized jacks. This equipment should not be used on party lines

or coin lines.

2. If this device is malfunctioning, it may also be causing harm to the

telephone network; this device should be disconnected until the source of

the problem can be determined and until the repair has been made. If this

is not done, the telephone company may temporarily disconnect service.

3. If you have problems with your telephone equipment after installing this

device, disconnect this device from the line to see if it is causing the

problem. If it is, contact your supplier or an authorized agent.

4. The telephone company may make changes in its technical operations and

procedures. If any such changes affect the compatibility or use of this

device, the telephone company is required to give adequate notice of the

changes.

5. If the telephone company requests information on what equipment is

connected to their lines, inform them of:

a. The telephone number that this unit is connected to.

b. The ringer equivalence number.

c. The USOC jack required: RJ-11C.

d. The FCC registration number.

Items (b) and (d) can be found on the unit’s FCC label. The ringer

equivalence number (REN) is used to determine how many devices can be

connected to your telephone line. In most areas, the sum of the RENs of all

devices on any one line should not exceed five (5.0). If too many devices

are attached, they may not ring properly.

6. In the event of an equipment malfunction, all repairs should be performed

by your supplier or an authorized agent. It is the responsibility of users

requiring service to report the need for service to the supplier or to an

authorized agent.

ASYNC/SYNC FIBER OPTIC MODEM AND FO MODEM CARD

CERTIFICATION NOTICE FOR

EQUIPMENT USED IN CANADA

The Canadian Department of Communications label identifies certified

equipment. This certification means that the equipment meets certain

telecommunications-network protective, operation, and safety requirements.

The Department does not guarantee the equipment will operate to the user’s

satisfaction.

Before installing this equipment, users should ensure that it is permissible

to be connected to the facilities of the local telecommunications company.

The equipment must also be installed using an acceptable method of

connection. In some cases, the company’s inside wiring associated with a

single-line individual service may be extended by means of a certified

connector assembly (extension cord). The customer should be aware that

compliance with the above conditions may not prevent degradation of service

in some situations.

Repairs to certified equipment should be made by an authorized Canadian

maintenance facility—in this case, your supplier. Any repairs or alterations

made by the user to this equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user to disconnect the

equipment.

Users should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines, and internal metallic water

pipe system, if present, are connected together. This precaution may be

particularly important in rural areas.

CAUTION:

Users should not attempt to make such connections themselves, but

should contact the appropriate electric inspection authority, or

electrician, as appropriate.

The LOAD NUMBER (LN) assigned to each terminal device denotes the

percentage of the total load to be connected to a telephone loop which is

used by the device, to prevent overloading. The termination on a loop may

consist of any combination of devices, subject only to the requirement that

the total of the load numbers of all the devices does not exceed 100.

ASYNC/SYNC FIBER OPTIC MODEM AND FO MODEM CARD

TRADEMARKS

ST®is a registered trademark of AT&T.

Any other trademarks mentioned in this manual are acknowledged to be the

property of the trademark owners.

ASYNC/SYNC FIBER OPTIC MODEM AND FO MODEM CARD

Contents

Chapter Page

1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3. Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.1 Configuration Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.2 Configuration Switch Set S1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.2.1 S1-1 through S1-4: Data Rate Setting . . . . . . . . . . . . . . . 13

3.2.2 S1-5 and S1-6: Clock Source. . . . . . . . . . . . . . . . . . . . . . . 13

3.2.3 S1-7: Asynchronous/Synchronous Mode . . . . . . . . . . . . 14

3.2.4 S1-8: Carrier-Control Method . . . . . . . . . . . . . . . . . . . . . 14

3.3 Configuration Switch Set S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.3.1 S2-1 and S2-2: Word Length . . . . . . . . . . . . . . . . . . . . . . 15

3.3.2 S2-3: Extended Signaling Rate. . . . . . . . . . . . . . . . . . . . . 15

3.3.3 S2-4 and S2-5: RTS/CTS Delay . . . . . . . . . . . . . . . . . . . . 15

3.3.4 S2-6 and S2-7: Not Used . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.3.5 S2-8: V.54 Loopback Test Enable . . . . . . . . . . . . . . . . . . 16

4. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.1 Fiber Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4.2 RS-232 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

5. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.1 Test Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5.1.1 Local Analog Loopback (LAL). . . . . . . . . . . . . . . . . . . . . 19

5.1.2 Remote Digital Loopback (RDL). . . . . . . . . . . . . . . . . . . 19

5.1.3 Using the V.52 BER Test Independently . . . . . . . . . . . . . 20

5.2 Power-On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Appendix: Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Black Box Modem

Black Box

Black Box 9600 FP Manuel utilisateur

Black Box

Black Box 202T Manuel utilisateur

Black Box

Black Box V.35 256/ST Series Manuel utilisateur

Black Box

Black Box ME375A Manuel utilisateur

Black Box

Black Box ME800A-R2 Manuel utilisateur

Black Box

Black Box MD885A-R2 Manuel utilisateur

Black Box

Black Box MD1621A Manuel utilisateur

Black Box

Black Box SHM-FSK Manuel utilisateur

Black Box

Black Box RM1600 Manuel utilisateur

Black Box

Black Box MDR210A-485 Manuel utilisateur

Black Box

Black Box ME795A Manuel utilisateur

Black Box

Black Box MAY 1994 Manuel utilisateur

Black Box

Black Box TL555A Manuel utilisateur

Black Box

Black Box MD3400A Manuel utilisateur

Black Box

Black Box ME376A-R2 Manuel utilisateur

Black Box

Black Box MPI Series Manuel utilisateur

Black Box

Black Box MD5010A Manuel utilisateur

Black Box

Black Box 40418 Manuel utilisateur

Black Box

Black Box Async MP Line Driver Card Manuel utilisateur

Black Box

Black Box MEG101AE-R4 Manuel utilisateur

Black Box

Black Box MD640A-ST-R2 Manuel utilisateur

Black Box

Black Box ME760A-R2 Manuel utilisateur

Black Box

Black Box MD1650A-JP Manuel utilisateur

Black Box

Black Box MD3450A Manuel utilisateur

Manuels Modem populaires d'autres marques

Davicom

Davicom DM562AP Manuel utilisateur

EpiValley

EpiValley TATA indicom SXC-1080 Manuel utilisateur

Zte

Zte WiMAX Manuel utilisateur

Intelimax

Intelimax MA-2060 Manuel utilisateur

SMC Networks

SMC Networks D3CM1604V Manuel d'utilisation et d'entretien

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuel utilisateur

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuel utilisateur

Samsung

Samsung AceLink SAM-335A Manuel utilisateur

Enfora

Enfora Enabler-G Guide de configuration rapide

iRZ

iRZ ATM2-232 Manuel utilisateur

Zhone

Zhone 6310 Manuel utilisateur

Paradyne

Paradyne Hotwire 7976 Manuel utilisateur

US Robotics

US Robotics 3453C Manuel utilisateur

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuel utilisateur

Zte

Zte MF823 Manuel utilisateur

Four-Faith

Four-Faith F1403 Manuel utilisateur

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuel utilisateur

Gemtek

Gemtek WiMAX WIXFBR-103 Manuel utilisateur