Bender PEM330 Manuel utilisateur

Quick start

PEM330/PEM333

PEM330-333_D00004_00_Q_XXEN/03.2013

These short instructions do not replace the operating manu-

al. You will find the operating manual on www.bender-de.com

Make sure that the personnel has read this manual and under-

stood all instructions relating to safety.

Short instructions

Intended use

The digital universal measuring device PEM330/PEM333 is suitable

for measuring and displaying electrical parameters of electricity

networks. The device measures current, voltage, energy consumpti-

on and power as well as the total harmonic distortion for assess-

ment of the voltage and current quality.

The accuracy of the active energy metering corresponds to class

0.5 S in compliance with the DIN EN 62053-22 (VDE 0418 Part 3-

22):2003-11.

Scope of delivery Safety instruction

●one PEM330 or PEM333

●important safety instructions for Bender Products

●these short instructions

●one sealing frame "IP54"

Danger of electric shock!

Follow the basic safety rules when working with electricity.

Consider the data on the rated voltage and supply voltage as

specified in the technical data!

Installing the device

Front panel mounting (front view, side view, panel cut-out)

A front panel cutout of 92 mm x 92 mm is required for the device.

1. Fit the device through the cut-out in the front panel.

2. Put the 4 transparent mounting brackets from behind on the edges of the device.

3. Push the clips tightly against the panel to secure the device.

4. Check the device to ensure that it is firmly installed in the front panel.

18 1862

9691

2PEM330-333_D00004_00_Q_XXEN/03.2013

Quick start PEM330/PEM333

Connection of the device

Wiring diagram

Connection

1. The connecting terminals are located on the rear. Connect

the PEM330/PEM333 to the supply voltage (terminals A1 and

A2 resp. +/-). Connect terminal " " to the protective con-

ductor.

2. Power protection by a 6 A fuse, quick response. If being sup-

plied from an IT system, both lines have to be protected by a

fuse.

3. Connection to the RS-485-Bus is made via the terminals D+,

D- and SH. Up to 32 devices can be connected to the bus. The

maximum cable length for the bus connection of all devices

is 1200 m.

Connection diagram voltage inputs

Three-phase 4-wire system (TN, TT, IT systems)

The PEM can be used in three-phase 4-wire systems, independent of

the type of distribution system (TN, TT, IT system).

Three-phase 3-wire system

The PEM can be used in three-phase 3-wire systems.

The line-to-line voltage must not exceed AC 400 V.

Connection via voltage transformers

The coupling via measuring voltage transformers allows the use of

a measuring device in medium and high voltage systems. The trans-

formation ratio in PEM330/PEM333 can be adjusted (1…2200).

I11

I12

I21

I22

I31

I32

DO13 DO14

DO23 DO24

DI1 DI2 DIC

D+

P1(RS-485) DO

• l11 l12 l22 l32 L1 L2 N• l21 • l31

24 DI1 DI2

DIC A2/

A1/

Terminal Description

A1, A2,

Supply voltage. Power protection by a 6 A fuse, quick re-

sponse. If being supplied from an IT system, both lines

have to be protected by a fuse.

DI1, DI2, DIC Digital inputs (PEM333 only)

DO13, DO14,

DO23, DO24

Digital outputs (N/O contacts) (PEM333 only)

I11, I12,

I21, I22,

I31, I32

Connection to the system to be monitored

D+, D-, SH Connection RS-485 bus (PEM333 only)

L1, L2, L3, N Measuring voltage inputs: The measuring leads should

be protected with appropriate fuses.

L1 L2 L3 N

PEM

AC 400 V / 230 V

L1 L2 L3

PEM

AC 400 V

L1 L2 L3 N

PEM

LV / MV / H

PEM330-333_D00004_00_Q_XXEN/03.2013

Quick start PEM330/PEM333

Commissioning

Check proper connection

During installation and connection, abide by the relevant standards

and regulations and follow the operating manuals for the device.

Before switching on

1. Before switching on think carefully about these questions:

2. Does the connected supply voltage US correspond to the

nameplates information?

3. Is the nominal system voltage of the measuring current

transformer not exceeded?

4. Does the measuring current transformer's maximum current

correspond to the nameplate information of the connected

device?

Switching on

After switching on, proceed as follows:

1. Connect the supply voltage.

2. Set the bus address/IP address.

3. Set the CT transformer ratio (for each channel).

4. Change the measuring current transformer's counting direc-

tion, if required.

5. Set the nominal voltage.

6. Select wye connection or delta connection.

Getting to know the operating elements

Legend

LED "kWh" and LED "kvarh": Pulse output

"SYSTEM" button: Display mean value and total value (current, vol-

tage); in the menu: in case of numerical values: move the cursor

one position to the left

"PHASE" button: Display line-conductor related measured quanti-

ties; in the menu: go up one entry;in case of numerical valu-

es: increasing the value

"ENERGY" button: Display measured values: Active and reactive

energy import/active and reactive energy export (line 4); in

the menu: move down one entry; in case of numerical valu-

es: reduce the value

"SETUP" button: Press > 3 s: switching between setup menu and

standard display; in the menu: selection of the parameter to

be edited; confirm entry

Data display

"SYSTEM" button

Column

left

Column

right

First

line

Second

line

Third

line

Ø IPges Power

factor λ

LL V

kvar

Ø ULL Qges F

kvar

kVA

Pges Qges Sges

Ln V

Wye con-

nection:

Ø ULN

Delta con-

nection:

Ø ULL

Ø IPges

AI4

Unbalance

Demand I1Demand I2Demand I3

kvar

kVA

Demand PDemand QDemand S

Button "ENERGY"

Parameters in the fourth line:

Column left Column right Value

kWh Active energy import

-- kWh Active energy export

kvarh Reactive energy import

-- kvarh Reactive energy export

S Apparent energy

4PEM330-333_D00004_00_Q_XXEN/03.2013

Quick start PEM330/PEM333

Bender GmbH & Co. KG Tel.: +49 6401 807-0 E-Mail: [email protected]m

Londorfer Str. 65 •35305 Gruenberg • Germany Fax: +49 6401 807-259 Web: http://www.bender-de.com

Postfach 1161 •35301 Gruenberg • Germany

Reprinting only with permission

of the publisher.

Subject to change!

©Bender GmbH & Co. KG

D0000400QXXEN

"PHASE" button

Column

left

Column

right First line Second line Third line

I1 I2 I3

UL1*UL2*UL3*

UL1L2 UL2L3 UL3L1

PL1*PL2*PL3*

var

QL1*QL2*QL3*

kVA

SL1*SL2*SL3*

λL1*λL2*λL3*

Displacement

factor

cos (φ)L1*

Displacement

factor

cos (φ)L2*

Displacement

factor

cos (φ)L3*

THD UL1 THD UL2 THD UL3

THD I1THD I2THD I3

Fk-factor I1k-factor I2k-factor I3

UPhase angle

UL1

Phase angle

UL2

Phase angle

UL3

Phase angle I1Phase angle I2Phase angle I3

"SETUP" button

Press the "SETUP" button for more than 3 s to access the setup

mode.

Press the "SETUP" button again to return to the default display

screen.

To be able to change parameters, you must first enter

the password. (factory setting: 0)

The following diagram will help you to familiarise yourself with

the menu:

enable energypulse EN PULSE

set backlight time out BLTO SET

Setup menu

PROGRAMMING

enter password PASSWORD

change password SET PASS enter new password NEW PASS

set wiring mode TYPE

select transformer ratio for the voltage transformer PT

set date DATE

* set baud rate BAUD

select current transformer ratio CT

set energypulse constant EN CONST

set demand DMD SET

set energyvalues SET ENGY

set clock CLK

clear energyCLR ENGY

clear peak demand CLR DMD

clear SOE CLR SOE

* set DO triggered mode DO CTRL

choose CT direction CT REV

set reactive energyimport kvarh

set active energyexport -kWh

set active energyimport kWh

info INFO

set reactive energyexport -kvarh

set apparent energykVAh

Serial number of device

Date of software update UPDATE

Protocol version PRO VER

Software Version SW-VER

* set address for measuring device ID

* set conguration paritybit CONFIG

choose kVA calcuation method KVA SET

choose power factor convention PF SET

set no. of sliding windows NUM

set demand period PERIOD

set DO1 control mode DO1

set I3 CT polarityI3 REV

set I2 CT polarityI2 REV

set I1 CT polarityI1 REV

set DO2 control mode DO2

* PEM333 only

Button

Note:

* In "delta connection" mode the display shows "– ".

Autres manuels pour PEM330

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bender Instrument de mesure

Bender

Bender LIM2000-1NL Manuel utilisateur

Bender

Bender EDS150 Manuel utilisateur

Bender

Bender LANTRAXX CMS460-D Manuel utilisateur

Bender

Bender ISOMETER isoLR275 Manuel utilisateur

Bender

Bender ISOMETER isoCHA425 Manuel utilisateur

Bender

Bender RCMA420 Manuel utilisateur

Bender

Bender ISOMETER isoRW425 Manuel utilisateur

Bender

Bender RCMA420 Manuel utilisateur

Bender

Bender ISOMETER isoLR275 Manuel utilisateur

Bender

Bender ISOMETER IR425-D4 Series Manuel utilisateur

Bender

Bender isoMED427P Manuel utilisateur

Bender

Bender RCMB42 EC Series Manuel utilisateur

Bender

Bender LINETRAXX VMD461 Manuel utilisateur

Bender

Bender RCMA423 Manuel utilisateur

Bender

Bender ISOMETER IR425-D4 Manuel utilisateur

Bender

Bender RC48N Manuel utilisateur

Bender

Bender ISOMETER isoPV1685RTU Manuel utilisateur

Bender

Bender RCM420 Series Manuel utilisateur

Bender

Bender isoMED427P-CX Manuel utilisateur

Bender

Bender ISOMETER isoPV with AGH-PV Manuel utilisateur

Bender

Bender MK2007CBM Manuel utilisateur

Bender

Bender iso685 Manuel utilisateur

Bender

Bender ISOMETER isoGEN523-S4-4 Manuel utilisateur

Bender

Bender ISOMETER IR420-D6 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur