Bellman & Symfon BE9026 Manuel utilisateur
Buttons and connections
Visit telephone transmitter
Test / program buttons
2.5 mm ext. trig.
Pre-mounted telephone cord
BE9251 Mobile phone sensor
Doorbell push button
3.5 mm ext. trig. BE9023 Magnetic switchBE9026 Contact matLED lights
BE9253
BE1431
In the box
BE1431 Visit telephone transmitter
2
¯1.5 V AA alkaline batteries
Telephone cord and adapter
Screw and wall plug
Power and battery
Battery power
2¯1.5 V AA lithium or alkaline
type batteries
Power consumption
Active < 70 mA
Idle position < 15 μA
Operation time
Alkaline batteries ~ 5 years
Lithium batteries ~ 10 years
Accessories
BE9251 Mobile phone sensor
BE9023 Magnetic switch
BE9026 Contact mat
BE9253 Ext. trig. cable, 3.5 mm
Inputs
RJ11 analogue telephone input
2.5 mm external trigger input
3.5 mm external trigger input
Frequency and coverage
Frequency: 314.91 MHz, 433.92 MHz
or 868.30 MHz, depending on region
Coverage: 50 - 250 m, 55 - 273 yd.
depending on the radio frequency
and the building’s characteristics
Dimensions and weight
Height: 100 mm, 4.0"
Width: 65 mm, 2.6"
Depth: 27 mm, 1.1"
Weight: 120 g, 4.2 oz. incl. batteries
Activation
The test buttons
A landline telephone
A smartphone or tablet via the
mobile phone sensor
A contact mat or magnetic switch
A doorbell connected to the ext trig
Environment
For indoor use only
Technical specications
Using a mobile phone
1 Use for instance a mobile phone to call the landline
telephone. The top LED on the transmitter lights up in
green to show that an incoming call is detected.
2 The yellow Visit LED on the receiver lights up to show
that the radio signal was received. In addition, it starts to
sound, ash or vibrate depending on the receiver.
Note: If you have changed the signal pattern, it will react
in accordance with the table on the following spread.
Setting up the transmitter
1Remove the battery pull tab to start the unit.
Clean the wall with the wet wipe and remove the protective lm from the Velcro.
2Mount the transmitter on the wall. You can also use the supplied screw and plug.
3Connect the telephone adapter as shown below.
Note: The appearance of the adapter may dier with territory.
1 2
Testing the connection
Using the test button
1 Press both test buttons simultaneously on the telephone
transmitter. The top LED lights up in green to show that
a radio signal is being transmitted.
2 The yellow Visit LED on the receiver lights up to show
that the signal was received. In addition, it starts to
sound, ash or vibrate depending on the receiver.
Note: If you have changed the signal pattern, it will react
in accordance with the table on the following spread.
3
1 2 1 2
Visit telephone transmitter
Visit telephone transmitter
Default signal pattern
When the telephone transmitter is activated by an incoming call or a triggered accessory, the following happens:
1The LED on the transmitter lights up to show that it’s signalling the receiver.
2The Visit LED on the receiver lights up and it starts to sound, ash or vibrate with a certain pace, called signal pattern.
The transmitter and the connected accessories determine the signal pattern. The default is as follows:
Transmitter Receiver signal pattern
Source LED LED Sound Vibration Flash
Landline phone Green, top Yellow light 1¯ring signal, low Medium Yes
Mobile phone sensor Green, top Yellow blinks 2¯ring signal, high Medium Yes
Other accessory Green, bottom Green light 1¯door chime, low Slow Yes
Changing the signal pattern
The transmitter controls the signal pattern. Open the transmitter front cover and move the
signal switches according to the table below to change it:
Transmitter Receiver signal pattern
Switch Source LED Sound Vibration Flash
Landline phone / test button Yellow light 1¯ring signal, low Medium Yes
Mobile phone sensor Yellow blinks 2¯ring signal, high Medium Yes
Other accessory Green light 1¯door chime, low Slow Yes
Landline phone / test button Yellow light 1¯ring signal, low Medium Yes
Mobile phone sensor Yellow blinks 2¯ring signal, high Medium Yes
Other accessory 2¯green blinks 2¯door chime, low Slow Yes
Landline phone / test button Yellow light 1¯ring signal, low Medium Yes
Mobile phone sensor Yellow blinks 2¯ring signal, high Medium Yes
Other accessory 3¯yellow blinks 1¯ring signal, high Medium Yes
Landline phone / test button Yellow light 1¯ring signal, low Medium Yes
Mobile phone sensor Yellow blinks 2¯ring signal, high Medium Yes
Other accessory 2¯orange blinks Baby melody Fast Yes
Landline phone / test button 2¯yellow blinks 2¯ring signal, low Fast Yes
Mobile phone sensor Yellow light 1¯ring signal, low Medium Yes
Other accessory 3¯orange blinks Baby melody Fast Yes
Landline phone / test button 2¯yellow blinks 2¯ring signal, low Medium Yes
Mobile phone sensor Orange blinks Baby melody Fast Yes
Other accessory Green blinks 2¯door chime, high Slow Yes
Landline phone / test button Orange blinks Baby melody Medium Yes
Mobile phone sensor 3¯yellow blinks 1¯ring signal, high Medium Yes
Other accessory 2¯green blinks 2¯door chime, low Slow Yes
Landline phone / test button 3¯yellow blinks 1¯ring signal, high Medium Yes
Mobile phone sensor 2¯yellow blinks 2¯ring signal, low Medium Yes
Other accessory Green blinks 2¯door chime, high Slow Yes
On
O
Changing the radio key
If your Visit system is activated for no reason, there is probably a nearby system that triggers yours. In order to avoid radio
interference you need to change the radio key on all units. The radio key switches are located under the transmitter cover.
Here is how you change the radio key:
1Open the transmitter front cover and move any radio key switch to the up (on position) to
change the radio key. By default, all radio key switches are positioned down (o).
2Press and hold the test/function button on the receiver until the green and yellow Visit LEDs
blink alternately. Release the button.
3Press both test buttons simultaneously on the transmitter within 30 seconds to send the new radio key.
4All Visit LEDs on the receiver blink 5 times to show that the radio key has been changed. It then returns to normal mode.
Note: All Visit units must be set to the same radio key in order to operate as a group.
°5
Troubleshooting
On
O
If Try this
The LEDs blink in orange every minute Replace the batteries. Only use 1.5 V AA (LR6) lithium or alkaline batteries.
The transmitter LED lights up in green
but the receiver doesn’t respond
Check the the transmitter batteries and the receiver batteries and connections.
Move the receiver closer to the transmitter to make sure it’s within radio range.
Check that the units are set to the same radio key, see Changing the radio key.
The transmitter LED doesn’t light up
when the phone rings or when an
accessory is triggered
Press the test buttons on the transmitter. If the LED lights up in green, check all
connections. If the LED doesn’t light up in green, replace the batteries. Only use
1.5 V AA (LR6) lithium or alkaline batteries.
The transmitter LED doesn’t light up
when I press the test buttons
Replace the batteries. Only use 1.5 V AA (LR6) lithium or alkaline batteries. If the
LED still doesn’t light up, contact your retailer for service information.
The receiver is activated for no
apparent reason
There is probably another Visit system installed nearby that triggers your
system. Change the radio key on all units, see Changing the radio key.
1 2 4
RADIO KEY
On
O
Visit telephone transmitter
3
Autres manuels Bellman & Symfon Émetteur
Bellman & Symfon
Bellman & Symfon BE1431 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon Bellman Visit 868 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1431 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1210 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1411 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1490 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon 2APAKBE1240 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1431 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon Visit BE1282 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon VISIT BE1420 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon Bellman Visit BE1023 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1431 Instructions de montage
Bellman & Symfon
Bellman & Symfon BE1431 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon VISIT BE1420 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1411-CO Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1411 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon Bellman Visit BE1123 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1431 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon BE1431 Manuel utilisateur
Bellman & Symfon
Bellman & Symfon Bellman Visit BE1023 Manuel utilisateur
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
