Belden HIRSCHMANN OCTOPUS OS24 Series Manuel utilisateur

Installation OCTOPUS OS20/OS24 Managed

Release

08/2017

Technical Support

https://hirschmann-support.belden.eu.com

User Manual

Installation

Managed IP65/67 Switch

OCTOPUS OS20 / OS24

OS20–000900T5T5TAFBHH OS20–000900T5T5TNEBHH

OS24–080900T5T5TNEBHHOS24–080900T5T5TFFBHH

P1 P2 RM FAULT

OS20-000900T5T5TAFBHH

x y

OCTOPUS

OS20

Managed

ETHERNET Switch

Power

OS20-000900T5T5TNEBHH

V24

FunctionPin

N.C.

GND

V24

Power

N.C.

P-

4N.C.

Pin Function

P+

Power

FAULT

RMP

x y

OCTOPUS

OS20

Managed

ETHERNET Switch

V24

FunctionPin

N.C.

GND

V24

Fault

Power

N.C.

Fault

P1 FAULT

RMP2

PoE

x y

OCTOPUS

OS24

Managed

ETHERNET Switch

OS24-080900T5T5TNEBHH

V24

FunctionPin

N.C.

GND

V24

Port 2-9

Power

N.C.

P-

4N.C.

Pin Function

P+

Power

FAULT

PoE

x y

OCTOPUS

OS24

Managed

ETHERNET Switch

OS24-080900T5T5TNEBHH

V24

FunctionPin

N.C.

GND

V24

N.C.

Fault

Port 2-9

OS20-000900T5T5TNEBHH

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

OCTOPUS OS20/OS24 Managed 25.8.17

Installation OCTOPUS OS20/OS24 Managed

Release

08/2017 3

Contents

Safety instructions 5

About this Manual 10

Legend 11

1 Description 12

1.1 General device description 12

1.2 Device name and product code 13

1.3 Device view 15

1.4 Power supply 19

1.4.1 Supply voltage with the characteristic value A 19

1.4.2 Supply voltage with the characteristic value F 19

1.4.3 Supply voltage with the characteristic value N 19

1.5 Ethernet ports 19

1.5.1 10/100 Mbit/s twisted pair port 19

1.5.2 10/100 Mbit/s PoE port 20

1.5.3 Pin assignments 21

1.6 Display elements 21

1.7 Management interfaces 23

1.7.1 V.24 interface (external management) 23

1.8 “FAULT” signal contact 24

2 Installation 25

2.1 Checking the package contents 25

2.2 Wiring the connectors for supply voltage and signal contact 26

2.2.1 Devices featuring supply voltage with the

characteristic value A 26

2.2.2 Devices featuring supply voltage with the

characteristic value F 27

2.2.3 Devices featuring supply voltage with the

characteristic value N 28

2.3 Installing and grounding the device 29

2.3.1 Grounding the device 30

2.4 Connecting the ferrite 31

2.5 Connecting the supply voltage 32

2.6 Operating the device 32

4Installation OCTOPUS OS20/OS24 Managed

Release

08/2017

2.7 Connecting data cables 32

3 Making basic settings 34

4 Monitoring the ambient air temperature 35

5 Maintenance and service 36

6 Technical data 37

A Further support 44

Installation OCTOPUS OS20/OS24 Managed

Release

08/2017 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning the device, turn off the supply voltage and return the

device to Hirschmann for inspection.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 37.

Connect to the product only components suitable for the requirements

of the specific application case.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow this instruction can result in death, serious injury, or

equipment damage.

Certification type

See “Device name and

product code” on page 13.

Operational environment

E On the inside of buildings

On the inside of trains

F On the inside of buildings

On the inside of trains

On the inside of ships

On the inside of vehicles

Table 1: Operational environment

6Installation OCTOPUS OS20/OS24 Managed

Release

08/2017

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

At ambient temperatures > 140 °F (60 °C):

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Grounding the device

The housing is grounded via the separate ground screw on the bottom left

of the front panel.

Use a wire diameter for the ground conductor that is no smaller than

the diameter of the supply voltage connection, however of at least

0.75 mm² (AWG18).

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

Shielding ground

The overall shield of a connected shielded twisted-pair cable is connected

to the metal housing as a conductor.

Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

Installation OCTOPUS OS20/OS24 Managed

Release

08/2017 7

Supply voltage

The supply voltage is electrically isolated from the housing.

Use undamaged parts.

Relevant for North America:

Only use copper wire/conductors of class 1, 75 °C.

Exclusively connect SELV circuits with the voltage restrictions in

accordance with IEC/EN 60950-1 to the signal contacts.

Applies to devices featuring supply voltage with the characteristic

value F:

Exclusively connect SELV circuits with the voltage restrictions in

accordance with IEC/EN 60950-1 to the supply voltage connections.

Applies to devices featuring supply voltage with the characteristic

value A:

Ensure that the externally power unit connected upstream fulfills one

of following conditions:

NEC Class 2

Limited Power Source based on EN 60950-1

Operating conditions

Operate the device at the specified ambient temperature (temperature of

the ambient air at a distance of 2 inches (5 cm) from the device) and at

the specified relative humidity exclusively.

Install the device in a location where the climatic threshold values

specified in the technical data are adhered to. Make sure the

environment does not heat the device.

Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

Relevant for use in North America

Use this device solely in Class 2 Circuits.

Relevant for usage under conditions that comply with the

the technical standard UL 60950-1:

Note: The following information applies only to device variants with

UL 60950-1 approval and protective conductor connection.

Protective conductor connection for the crimp connection:

Use a wire diameter for the ground conductor that is no smaller than the

diameter of the supply voltage connection, however of at least 0.75 mm²

(AWG18).

Use a professional crimping tool specified for the wire size. Follow the

instruction of the crimping tool. The pull out force the crimped connection

is at least 135 N according to the technical standard IEC 60352-2.

8Installation OCTOPUS OS20/OS24 Managed

Release

08/2017

E marking

The labeled devices comply with the regulations contained in the following

European directive(s):

Regulation No. 10 of the Economic Commission for Europe of the United

Nations (UN/ECE): Devices with an approval are labeled with the

E type approval mark.

(Relevant for devices with certification type F)

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/35/EU

Directive of the European Parliament and of the Council on the

harmonisation of the laws of the Member States relating to the making

available on the market of electrical equipment designed for use within

certain voltage limits.

2014/30/EU (EMC)

Directive of the European Parlament and of the Council on the

harmonisation of the laws of the Member States relating to

electromagnetic compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55032

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

Installation OCTOPUS OS20/OS24 Managed

Release

08/2017 9

FCC note:

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

10 Installation OCTOPUS OS20/OS24 Managed

Release

08/2017

About this Manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

The documentation for your device is made up of the following documents:

General safety instructions

Installation user manual

Basic Configuration user manual

Redundancy Configuration user manual

Reference manual for the graphical user interface

Command Line Interface reference manual

You find these manuals as PDF files on the Internet on the Hirschmann

product pages (www.hirschmann.com).

The Industrial HiVision Network Management software provides you with

additional options for smooth configuration and monitoring:

ActiveX control for SCADA integration

Auto-topology discovery

Browser interface

Client/server structure

Event handling

Event log

Simultaneous configuration of multiple devices

Graphical user interface with network layout

SNMP/OPC gateway

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Belden Changer

Belden

Belden HIRSCHMANN MACH 100 Series Manuel utilisateur

Belden

Belden Hirschmann IT MAMMUTHUS MTS26 Series Manuel utilisateur

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manuel utilisateur

Belden

Belden Hirschmann MACH102 Series Manuel utilisateur

Belden

Belden grass valley KULA AV Manuel utilisateur

Belden

Belden HIRSCHMANN SPIDER II 16TX EEC Manuel utilisateur

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTS2948X-6Q-A Manuel utilisateur

Belden

Belden HIRSCHMANN SPIDER II Manuel utilisateur

Belden

Belden ThinkLogical TLX12 Manuel utilisateur

Belden

Belden HIRSCHMANN GREYHOUND GRM Series Manuel utilisateur

Belden

Belden Hirschmann RS20 Series Manuel utilisateur

Belden

Belden HIRSCHMANN EESX Series Guide de configuration rapide

Belden

Belden Hirschmann MACH104 Series Guide de l'utilisateur

Belden

Belden Hirschmann GREYHOUND GRS1042 Manuel utilisateur

Belden

Belden Telecast Fiber Systems THOR-SLG Manuel utilisateur

Belden

Belden HIRSCHMANN IT MAMMUTHUS MTM8000 Series Manuel utilisateur

Belden

Belden Hirschmann HiOS-2S Manuel utilisateur

Belden

Belden Grass Valley K-Frame Comment utiliser

Belden

Belden Hirschmann SPIDER Standard Line Series Manuel utilisateur

Belden

Belden lumberg automation 0960 IOL 3816-001 Manuel utilisateur

Belden

Belden Hirschmann MACH104-PoEP Series Manuel utilisateur

Belden

Belden HIRSCHMANN Dragon PTN CSM310-A Manuel utilisateur

Belden

Belden Hirschmann SPIDER II 8TX Manuel utilisateur

Belden

Belden grass valley SIRIUS 800 Series Guide de l'utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur