Beckhoff CX2550 Series Manuel utilisateur
Manual
CX2550-0179 / CX2550-0279
USB extension for CX20xx
1.0
2014-03-11
Version:
Date:
Table of contents
CX2550-0179 / CX2550-0279 3Version: 1.0
Table of contents
1 Foreword ....................................................................................................................................................5
1.1 Notes on the documentation........................................................................................................... 5
1.2 Safety instructions .......................................................................................................................... 6
1.3 Documentation issue state ............................................................................................................. 7
2 Product overview.......................................................................................................................................8
2.1 Intended use ................................................................................................................................... 8
2.2 System overview............................................................................................................................. 9
2.3 CX2550-0179 - Technical data ..................................................................................................... 10
2.4 CX2550-0279 - Technical data ..................................................................................................... 11
3 Mounting and wiring ...............................................................................................................................12
3.1 Unpacking, installation and transport............................................................................................ 12
3.2 Dimensions ................................................................................................................................... 13
3.3 Attaching the system interface to the CX20x0 system ................................................................. 14
3.4 Installation on the mounting rail .................................................................................................... 14
3.5 Mounting the module lock............................................................................................................. 17
3.6 USB connection ............................................................................................................................ 19
4 Commissioning / Configuration .............................................................................................................20
4.1 EtherCAT cable redundancy......................................................................................................... 20
4.2 Switching on and off ..................................................................................................................... 23
5 CX2550-0179 - Architecture description................................................................................................24
6 Error handling and diagnostics .............................................................................................................25
6.1 LEDs Diagon the USB extension.................................................................................................. 25
6.2 Faults ............................................................................................................................................ 26
7 Decommissioning....................................................................................................................................27
7.1 Disassembly and disposal ............................................................................................................ 27
8 Appendix ..................................................................................................................................................29
8.1 Certifications ................................................................................................................................. 29
8.2 Support and Service ..................................................................................................................... 30
Table of contents
CX2550-0179 / CX2550-02794 Version: 1.0
Foreword
CX2550-0179 / CX2550-0279 5Version: 1.0
1 Foreword
1.1 Notes on the documentation
This description is only intended for the use of trained specialists in control and automation engineering who
are familiar with the applicable national standards.
It is essential that the documentation and the following notes and explanations are followed when installing
and commissioning the components.
It is the duty of the technical personnel to use the documentation published at the respective time of each
installation and commissioning.
The responsible staff must ensure that the application or use of the products described satisfy all the
requirements for safety, including all the relevant laws, regulations, guidelines and standards.
Disclaimer
The documentation has been prepared with care. The products described are, however, constantly under
development.
We reserve the right to revise and change the documentation at any time and without prior announcement.
No claims for the modification of products that have already been supplied may be made on the basis of the
data, diagrams and descriptions in this documentation.
Trademarks
Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®, XFC® and XTS® are registered
trademarks of and licensed by Beckhoff Automation GmbH.
Other designations used in this publication may be trademarks whose use by third parties for their own
purposes could violate the rights of the owners.
Patent Pending
The EtherCAT Technology is covered, including but not limited to the following patent applications and
patents:
EP1590927, EP1789857, DE102004044764, DE102007017835
with corresponding applications or registrations in various other countries.
The TwinCAT Technology is covered, including but not limited to the following patent applications and
patents:
EP0851348, US6167425 with corresponding applications or registrations in various other countries.
EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH,
Germany
Copyright
© Beckhoff Automation GmbH & Co. KG, Germany.
The reproduction, distribution and utilization of this document as well as the communication of its contents to
others without express authorization are prohibited.
Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a
patent, utility model or design.
Foreword
CX2550-0179 / CX2550-02796 Version: 1.0
1.2 Safety instructions
Safety regulations
Please note the following safety instructions and explanations!
Product-specific safety instructions can be found on following pages or in the areas mounting, wiring,
commissioning etc.
Exclusion of liability
All the components are supplied in particular hardware and software configurations appropriate for the
application. Modifications to hardware or software configurations other than those described in the
documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.
Personnel qualification
This description is only intended for trained specialists in control, automation and drive engineering who are
familiar with the applicable national standards.
Description of symbols
In this documentation the following symbols are used with an accompanying safety instruction or note. The
safety instructions must be read carefully and followed without fail!
DANGER
Serious risk of injury!
Failure to follow the safety instructions associated with this symbol directly endangers the
life and health of persons.
WARNING
Risk of injury!
Failure to follow the safety instructions associated with this symbol endangers the life and
health of persons.
CAUTION
Personal injuries!
Failure to follow the safety instructions associated with this symbol can lead to injuries to
persons.
Attention
Damage to the environment or devices
Failure to follow the instructions associated with this symbol can lead to damage to the en-
vironment or equipment.
Note
Tip or pointer
This symbol indicates information that contributes to better understanding.
Foreword
CX2550-0179 / CX2550-0279 7Version: 1.0
1.3 Documentation issue state
Version Changes
1.0 first Version
Product overview
CX2550-0179 / CX2550-02798 Version: 1.0
2 Product overview
2.1 Intended use
The CX20x0 device series is a modular control system designed for DIN rail installation. The system is
scalable, so that the required modules can be assembled and installed in the control cabinet or terminal box
as required.
Only switch the PC off after closing the software
Before the Embedded PC is switched off, the software currently running on it should be stopped properly in
order to avoid data loss on the hard disk. Please read the section on “Switching off”.
Switch off all system components and uncouple the Industrial PC from the system if the PC is not used for
control purposes, e.g. during a function test. To disconnect first pull the first terminal behind the power
supply unit (optional), then pull the connectors of the fieldbus connections.
System components that have been switched off must be secured against being switched on again.
The Embedded PC’s power supply unit must be supplied with 24VDC.
Attention
Damage to the environment or devices
Do not exchange any parts when under power! The exchange of controller parts when live
can lead to short-circuits or overvoltages. These can damage the controller itself and con-
nected peripherals (terminals, monitors, input devices, etc.).
When components are being fitted or removed, the supply voltage must be switched off.
Software knowledge
Attention
System malfunctions
Mandatory software knowledge! Every user must be familiar with any of the functions of the
software installed on the PC that he can reach.
Product overview
CX2550-0179 / CX2550-0279 9Version: 1.0
2.2 System overview
CX2550-0x79 system module USB extension
The CX2550-0x79 systems modules are attachments for the CX2000 Embedded PC series. They transmit
USB signals via a CAT 5e cable over distances of up to max. 50 m. The CX2550-0179 system module
transmits USB signals according to the USB 1.1 standard (full speed, max. 12 Mbit/s) while the
CX2550-0279 system module transmits USB signals according to the USB 2.0 standard (high speed, max.
480 Mbit/s). Both modules can be attached at the right-hand side of a CX20x0-CPU and are placed between
the power supply unit and the CPU. The internal connection is made via a USB port of the CX20x0-CPU; this
way, no PCI Express resources are required or used. No additional drivers are required for operation since
signal transformation and forwarding of the USB signals take place at the electrical level and are completely
transparent for the operating system.
The CX2550-0179 and CX2550-0279 modules enable the direct connection of Beckhoff Control Panels with
USB Extended interface. The CX2550-0179 system module is suitable for the connection of the Beckhoff
CP69xx and CP79xx Control Panel series with USB Extended 1.1 connection. The CX2550-0279 system
module is suitable for the connection of the Beckhoff CP29xx and CP39xx Control Panel series with USB
Extended 2.0 connection.
Product overview
CX2550-0179 / CX2550-027910 Version: 1.0
2.3 CX2550-0179 - Technical data
The system module CX2550-0179 transmits USB signals according to USB 1.1 standard (full speed, max. 12
Mbit/s).
Technical data CX2550-0179
Interfaces 1 x USB Extended 1.1
Type of connection RJ 45socket
Properties transmission of USB1.1 up to max. 50 m via CAT-5e cable
Diagnostics LED 1 x power, 1 x speed, 1 x +15V, 1 x suspend
Power supply via system bus (via power supply module CX2100-0xxx)
Dimensions (W x H x D) 24 mm x 99 mm x 54.5 mm
Weight approx. 189 g
Operating/Storage temperature -25° C ... +60° C / -40° C ... +85° C
Relative humidity 95% no condensation
Vibration/shock resistant conforms to EN 60068-2-6 / EN 60068-2-27
EMC immunity/emission conforms to EN 61000-6-2/EN 61000-6-4
Protection class IP 20
Further Information: www.beckhoff.de/CX2000
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Beckhoff Unité de contrôle
Beckhoff
Beckhoff C9900-G072 Guide de l'utilisateur
Beckhoff
Beckhoff M310 Manuel utilisateur
Beckhoff
Beckhoff EK9500 Manuel de l'opérateur
Beckhoff
Beckhoff EM2042 Manuel de l'opérateur
Beckhoff
Beckhoff EL3356-00 0 Series Manuel de l'opérateur
Beckhoff
Beckhoff EP1 Series Manuel de l'opérateur
Beckhoff
Beckhoff AX5801 Manuel utilisateur
Beckhoff
Beckhoff CX2550-0020 Manuel utilisateur
Beckhoff
Beckhoff EPP3744 041 Series Manuel utilisateur
Beckhoff
Beckhoff TF6120 Manuel utilisateur
Beckhoff
Beckhoff C9900-M800 Manuel utilisateur
Beckhoff
Beckhoff M1400 Mode d’emploi
Beckhoff
Beckhoff EPI1 Series Manuel utilisateur
Beckhoff
Beckhoff EP6224 Manuel de l'opérateur
Beckhoff
Beckhoff KL2502 Manuel de l'opérateur
Beckhoff
Beckhoff PS9011-2420-0001 Manuel de l'opérateur
Beckhoff
Beckhoff EP7041 Series Manuel de l'opérateur
Beckhoff
Beckhoff KS2502 Manuel de l'opérateur
Beckhoff
Beckhoff EPI2 Series Manuel de l'opérateur
Beckhoff
Beckhoff AX2090-TS50-3000 Manuel de l'opérateur
Manuels Unité de contrôle populaires d'autres marques
Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur
JS Automation
JS Automation MPC3034A Manuel utilisateur
JAUDT
JAUDT SW GII 6406 Series Guide rapide
Spektrum
Spektrum Air Module System Manuel utilisateur
BOC Edwards
BOC Edwards Q Series Manuel utilisateur
