BAFANG DP C13.CAN Manuel utilisateur

BF-UM-C-DP C13-EN November 2019

USER MANUAL FOR DISPLAY

CONTENT

7.1 Important Notice 

7.2 Introduction of Display 2

7.3 Product Description 3

7.3.1 Specifications 3

7.3.2 Functions Overview 3

7.4 Display 4

7.5 Key Definition 4

7.6 Normal Operation 5

7.6.1 Switching the System ON/OFF 5

7.6.2 Selection of Support Levels 5

7.6.3 Headlights / backlighting 5

7.6.4 Walk Assistance 5

7.6.5 Selection mode 5

7.6.6 ”Service Tip” 6

7.6.7 ”Error code” indication 6

7.6.8 Battery capacity indication 6

7.7 Settings 7

7.7.1 Setting 7

7.7.2 View Information 8

7.8 Error Code Definition 12

7 USER MANUAL FOR

DP C13.CAN

2BF-UM-C-DP C13-EN November 2019

7.2 INTRODUCTION OF DISPLAY

• Model: DP C13.CAN BUS

• The liquid crystal display is made of hard-

ened PMMA, the key button is made of

silicone rubber.

• The label marking is as follows:

Note: Please keep the QR code label attached

to the display cable. The information from the

Label is used for a later possible software

update.

7.1 IMPORTANT NOTICE

• If the error information from the display

cannot be corrected according to the inst-

ructions, please contact your retailer.

• The product is designed to be waterproof. It

is highly recommended to avoid submerging

the display under water.

• Do not clean the display with a steam jet,

high-pressure cleaner or water hose.

• Please use this product with care.

• Do not use thinners or other solvents to

clean the display. Such substances can

damage the surfaces.

• Warranty is not included due to wear and

normal use and aging.

BF-UM-C-DP C13-EN November 2019

USER MANUAL FOR DISPLAY

7.3 PRODUCT DESCRIPTION

7.3.1 Specifications

• Operating temperature: -20℃~45℃

• Storage temperature: -20℃~50℃

• Waterproof: IP65

• Bearing humidity: 30%-70% RH

7.3.2 Functional Overview

• Speed display (switching between km and

miles).

• Battery capacity indication.

• The lighting system.

• Indication of performance support.

• Kilometer stand (including single-trip dis-

tance, total distance).

• Time display for single journeys.

• Walk assistance.

• Energy consumption indicator CALORIES

(Note: If the display has this function)

• Display for the remaining distance.(Depends

on your riding style)

• Indication of error messages.

4BF-UM-C-DP C13-EN November 2019

7.4 DISPLAY

1Display of battery capacity in real time

2Speed display in real-time

3Data: Display data, which corresponds to the

current mode

4The display shows , if the light is on.

5Speed display in real-time

6Support level

7Speed unit

8Unit indicator

7.5 KEY DEFINITION

Mode/System On/Off

Down

BF-UM-C-DP C13-EN November 2019

USER MANUAL FOR DISPLAY

7.6 NORMAL OPERATION

7.6.1 Switching the System ON/OFF

Press and hold (>2S) on the display to

turn on the system. Press and hold (>2S)

again to turn off the system.

If the "automatic shutdown time" is set to 5

minutes (it can be reset with the "Auto Off"

function, See "Set Auto Off"), the display

will automatically be turned off within the

desired time when it is not in operation.

7.6.2 Selection of Support Levels

When the display is turned on, press the

or button (>2S) to switch to the support

level, the lowest level is 0, the highest level

is 5 (the amount of support level can be

set). When the system is switched on, the

support level starts in level 1. There is no

support at level 0.

7.6.3 Headlights / backlighting

Hold the button (>2S) to activate the

frontlight and taillights.

Hold the button (>2S) again to turn off

the frontlight and taillights. The brightness

of the backlight can be set in the display

settings "Brightness".

7.6.4 Walk Assistance

The Walk assistance can only be activated

with a standing pedelec.

Activation: Press the continuously until

this symbol appears. Next hold down

the button whilst the symbol is

displayed, now the Walk assistance will

activate. The symbol will blink and

the pedelec moves approx. 5 km/h. After

releasing the button, the motor stops

automatically and switches back to level 0.

7.6.5 Selection mode

Brieﬂy press (0.5s) to view the different

Kilometer stand: total kilometers (ODO) -

daily kilometers (TRIP) - Remaining distance

(go) - Time (TIME) - Power Output (W) -

Energy consumption (SC) - Maximum speed

(MAX) - Average speed (AVG).

NOTE: Energy consumption is ﬁtted only

with torque sensor.

6BF-UM-C-DP C13-EN November 2019

7.6.6 ”Service Tip”

If the “Service" function switch on, every 5000 km (the mileage of more than 5000 km) the indicator

"mA" is displayed every time at switch on.

The “Service" function can be turned off and on in the setting interface. See details for operation in

“Setting” part.

7.6.7 ”Error code” indication

When the the pedelec is at failure, the display will automatically show the error code and the screen

will ﬂash. Please refer to the detailed error code in “ERROR CODE DEFINITION” part.

NOTE: Only when the fault is eliminated can you exit the fault interface. The pedelec will not be able

to continue work at failure.

7.6.8 Battery capacity indication

The battery capacity is displayed in real time as 100% to 0% (as shown in the ﬁgure below).

<5% 5%-20% 20%-40% 40%-60% 60%-80% 60%-100%

BF-UM-C-DP C13-EN November 2019

USER MANUAL FOR DISPLAY

7.7 SETTINGS

After the display is turned on, press and hold

(>2S) the and button at same time to

access the “Setting” interface. pressing the

or button, you can select and reset

the items.

Brieﬂy press (<0.5S) the button your can

conﬁrm your selected option or access the

next “Setting” interface, you can also press

and hold (>2S) the and button at

the same time to save them and exit to the

“Setting” interface.

If no button is pressed within 1 minute

in “Setting” interface, the display will

automatically exit setting and no data will be

saved.

7.7.1 Setting

7.7.1.1 Reset mileage

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface and “tC” appears

on the display (as shown below). Now using

the or button, choose between “y”

or “n”. If choose “y”, will the Daily kilome-

ters (TRIP), Maximum speed (MAX), Average

speed (AVG) and time(TIME) be reset.

Once you have chosen your desired selec-

tion, press (<0.2S) the button to save

and to enter next item "Selections in km/

Miles".

7.7.1.2 Selections in km/Miles

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface, repetitively press

the button until the “U” appears on the

display (as shown below). Now using the

or button, choose between “mile/h”

or “km/h” (U-1 or U-2).

Once you have chosen your desired selec-

tion, press (<0.2S) the button to save

and to enter next item "Set light sensitivity".

7.7.1.3 Set display brightness

When the system is on, press and hold (>2S)

the and button at same time to

access the “Setting” interface, repetitively

press the button until the “bLE” appears

on the display (as shown below). And then

press to increase or to reduce

(brightness for 1-8).

Once you have chosen your desired selec-

tion, press (<0.3S) the button to save

and to enter next item "Set Auto Off".

8BF-UM-C-DP C13-EN November 2019

7.7.1.4 Set Auto Off

When the system is on, press and hold (>2S)

the and button at same time to

access the “Setting” interface, repetitively

press the button until the “oFt” appears

on the display (as shown below). And then

press to increase or to reduce (Auto

Off for 1-9 minute).

Once you have chosen your desired selec-

tion, press (<0.3S) the button to save

and to enter next item "Service Tip".

7.7.1.5 Set support level

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface, repetitively press

the button until the “dH” appears on the

display (as shown below). And then press

or to select support level (3,5,9), The

level is 5 in default.

Once you have chosen your desired selec-

tion, press (<0.2S) the button to save

and to enter next item "Wheel Size".

7.7.2 View Information

All data in this item cannot be changed, only to

be viewed.

7.7.2.1 Wheel Size

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface, repetitively press

the button until the “LUd” appears on

the display (as shown below). And you can

press and hold (>2S) the and button

together exit to the main interface.

Once you have viewed your desired informa-

tion, press (<0.2S) the button to enter

next item "Speed Limit".

7.7.2.2 Speed Limit

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface, repetitively press

the button until the “SPL” appears on

the display (as shown below). And you can

press and hold (>2S) the and button

together exit to the main interface.

Once you have viewed your desired informa-

tion, press (<0.2S) the button to enter

next item "Controller software info".

BF-UM-C-DP C13-EN November 2019

USER MANUAL FOR DISPLAY

7.7.2.3 Controller Software info

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface, repetitively press

the button until the “CSc” (Controller

Software check) appears on the display (as

shown below). And you can press and hold

(>2S) the and button together exit

to the main interface.

Once you have viewed your desired informa-

tion, press (<0.2S) the button to enter

next item "Controller hardware info".

7.7.2.4 Controller Hardware info

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface, repetitively press

the button until the “CHc” (Controller

Hardware check) appears on the display (as

shown below). And you can press and hold

(>2S) the and button together exit

to the main interface.

Once you have viewed your desired informa-

tion, press (<0.2S) the button to enter

next item "Display software info".

7.7.2.5 Display Software info

When the system is on, press and hold (>2S)

the and button at same time to

access the “Setting” interface, repetitively

press the button until the “dSc” (Display

Software check) appears on the display (as

shown below). And you can press and hold

(>2S) the and button together exit

to the main interface.

Once you have viewed your desired informa-

tion, press (<0.2S) the button to enter

next item "Display hardware info".

7.7.2.6 Display Hardware info

When the system is on, press and hold (>2S)

the and button at same time to

access the “Setting” interface, repetitively

press the button until the “dHc” (Display

Hardware check) appears on the display (as

shown below). And you can press and hold

(>2S) the and button together exit

to the main interface.

Once you have viewed your desired informa-

tion, press (<0.2S) the button to enter

next item "Sensor Software info".

10 BF-UM-C-DP C13-EN November 2019

7.7.2.7 Sensor Software info

When the system is on, press and hold (>2S)

the and button at same time to

access the “Setting” interface, repetitively

press the button until the “SSc” (Sensor

Software check) appears on the display (as

shown below). And you can press and hold

(>2S) the and button together exit

to the main interface.

Once you have viewed your desired informa-

tion, press (<0.2S) the button to enter

next item "Sensor Hardware info".

7.7.2.8 Sensor Hardware info

When the system is on, press and hold (>2S)

the and button at same time to

access the “Setting” interface, repetitively

press the button until the “SHc” (Sensor

Hardware check) appears on the display (as

shown below). And you can press and hold

(>2S) the and button together exit

to the main interface.

Once you have viewed your desired informa-

tion, press (<0.2S) the button to enter

next item “Service Tip”.

7.7.2.9 “Service Tip”

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface, repetitively press

the button until the “nn A” appears on

the display (as shown below). And then

press or to select “0” or “1”. Chose

0 means turn off the notiﬁcation.

You can also press and hold (>2S) the

and button together exit to the main

interface.

Once you have chosen your desired selec-

tion, press (<0.2S) the button to save

and to enter next item "Message of Error

Code".

7.7.2.10Message of Error Code

When the system is on, press and hold (>2S)

the and button at same time to ac-

cess the “Setting” interface, repetitively press

the button until the “E0-00” appears

on the display (as shown below). And then

press or to view “E0-00” to “E9-00”.

Chose 0 means turn off the notiﬁcation.

You can also press and hold (>2S) the

and button together exit to the main

interface.

Once you have viewed your desired selec-

tion, press (<0.2S) the button to enter

next item "Battery info".

Table des matières

Autres manuels BAFANG Accessoires pour vélos

BAFANG

BAFANG BT C01.340.UART Guide de référence

BAFANG

BAFANG DP C171.UART Manuel utilisateur

BAFANG

BAFANG DP E170.CAN Manuel utilisateur

BAFANG

BAFANG C966 Instructions de fonctionnement

BAFANG

BAFANG M800 Manuel utilisateur

BAFANG

BAFANG DP C10.UART Manuel utilisateur

BAFANG

BAFANG C961 Manuel utilisateur

BAFANG

BAFANG DP C240.CAN Manuel utilisateur

BAFANG

BAFANG DP C181.CAN Manuel utilisateur

BAFANG

BAFANG DP C10.CAN Manuel utilisateur

BAFANG

BAFANG DP E171.CAN Manuel utilisateur

BAFANG

BAFANG M510 Manuel utilisateur

BAFANG

BAFANG DP C01.RS 232.7 Manuel utilisateur

BAFANG

BAFANG DP C230.CAN Manuel utilisateur

BAFANG

BAFANG DP C15.UART Manuel utilisateur

BAFANG

BAFANG BT C01.340.UART Guide de référence

BAFANG

BAFANG E-SYSTEM Manuel utilisateur

BAFANG

BAFANG DP C18.CAN Manuel utilisateur

BAFANG

BAFANG DP E08.CAN Manuel utilisateur

BAFANG

BAFANG MM G333.250.C Manuel utilisateur

BAFANG

BAFANG DP E170.CAN Manuel utilisateur

BAFANG

BAFANG DP C10.UART Manuel utilisateur

BAFANG

BAFANG H310 Manuel utilisateur

BAFANG

BAFANG DP C231.CAN Manuel utilisateur

Manuels Accessoires pour vélos populaires d'autres marques

Sigma

Sigma BC 16.16 Manuel utilisateur

Playcore

Playcore Dero Setbacks Manuel utilisateur

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manuel utilisateur

Cateye

Cateye RAPID X2 Manuel utilisateur

buratti meccanica

buratti meccanica Clorofilla Trail Manuel utilisateur

Shimano

Shimano SG-8R20 Mode d'emploi

BOB

BOB YAK Manuel utilisateur

APLIC

APLIC 303303/20190717TW012 Manuel utilisateur

SRAM

SRAM AXS BlipBox Manuel utilisateur

Garmin

Garmin EDGE 500 Manuel utilisateur

Shimano

Shimano FD-RX810 Manuel utilisateur

Cateye

Cateye V2C - Manuel d'instructions

KMART

KMART 43115907 Manuel utilisateur

SIGMA SPORT

SIGMA SPORT Buster 2000 Manuel utilisateur

NVO Components

NVO Components STEM Manuel utilisateur

DAXYS

DAXYS BP188 Manuel utilisateur

XLC

XLC BV-W17 Manuel utilisateur

Deda Elementi

Deda Elementi SUPERBOX Manuel utilisateur