BAFANG H500F Manuel utilisateur

DEALER MANUAL FOR MOTOR

BF-DM-C-RM G060-DC-EN November 2019

6.1 Introduction 

6.2 Specifications 3

6.2.1 Outline and geometric size 3

6.2.2 Surface 3

6.2.3 Storage Information 3

6.3 Drive Unit Installation 4

6.3.1 List of Tools to be used 4

6.3.2 Motor Installation 4

6.4 Maintenance 5

CONTENT

6 DEALER MANUAL FOR H500F

(RM G060.350.DC)

2BF-DM-C-RM G060-DC-EN November 2019

6.1 INTRODUCTION

•Product Model

RM G060.350.DC

•Scope

Applies only to electrically powered pedelecs

developed or licensed by Bafang. It is suitable

for fat bikes or all terrain bikes, which have been

developed for off road on gravel or sand use.

The engine is not suitable for sport competi-

tions.

•Identiﬁcation

The following graphic, is the identification

numbers of the product, which are shown on

the housing:

Note: Content in the label is important informa-

tion about this product. Please do not remove

the information from the motor.

DEALER MANUAL FOR MOTOR

BF-DM-C-RM G060-DC-EN November 2019

6.2 SPECIFICATIONS

Motor model: RM G060.350.DC

Rated power (W) 350

Rated voltage (V) 36

Waterproof IP65

Certiﬁcation CE - EMC

Outdoor Temperatures -20℃~45℃

6.2.1 Outline and geometric size

OLD: 175mm

Shaft length: 235mm

Motor cable length: L=250mm

6.2.2 Surface

Shockproof black coating

6.2.3 Storage Information

The pedelec should be stored in a ventilated dry room. Avoid storing the pedelec near strong magnetic

objects.

4BF-DM-C-RM G060-DC-EN November 2019

6.3 DRIVE UNIT INSTALLATION

6.3.1 List of Tools to be used

Use of the Tools Tools

To tighten/loosen the M5*8 screws onto the disc brake. Internal hex wrench

To tighten/loosen the M12 flange nuts. Open spanner

6.3.2 Motor Installation

1. First mount the cassette on the cassette

seat.

2. Tighten the disk brake with six screws onto

motor.

3. Insert the stop pin into on the shaft.

4. Insert the motor into the frame.

5. Mount the 4mm washer on both sides of

the frame.

DEALER MANUAL FOR MOTOR

BF-DM-C-RM G060-DC-EN November 2019

6. Tighten clockwise M12 ﬂange nuts with

open spanner at both sides of the motor.

(torque requirement: 47-60 N.m.)

7. Mount the shaft end sheath on both sides

of the shaft ends.

6.4 MAINTENANCE

• Maintenance must be carried out by autho-

rized personnel with the correct equipment.

• Do not disassemble the motor.

• Do not use thinners or other solvents to

clean the components. Such substances can

damage the surfaces.

• Avoid water submerging, to keep the com-

ponents protected.

• Avoid using high-pressure cleaning jets.

• For prolonged storage, turn off the battery

and avoid storing near heat sources.

6BF-DM-C-RM G060-DC-EN November 2019

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels BAFANG Accessoires pour vélos

BAFANG

BAFANG DP C15.CAN Manuel utilisateur

BAFANG

BAFANG DP C10.UART Manuel utilisateur

BAFANG

BAFANG DP C15.UART Manuel utilisateur

BAFANG

BAFANG BT F15.655.C Manuel utilisateur

BAFANG

BAFANG C966 Instructions de fonctionnement

BAFANG

BAFANG DP C240.CAN Manuel utilisateur

BAFANG

BAFANG DPC-10 Biktrix Manuel utilisateur

BAFANG

BAFANG M625 Manuel utilisateur

BAFANG

BAFANG DP C181.CAN Manuel utilisateur

BAFANG

BAFANG BT C01.340.UART Guide de référence

BAFANG

BAFANG DP C01.CAN BUS Manuel utilisateur

BAFANG

BAFANG H550 Manuel utilisateur

BAFANG

BAFANG BT C01.340.UART Manuel utilisateur

BAFANG

BAFANG H600 Manuel utilisateur

BAFANG

BAFANG DP C10.UART Manuel utilisateur

BAFANG

BAFANG DP C171.UART Manuel utilisateur

BAFANG

BAFANG DP C01.RS 232.7 Manuel utilisateur

BAFANG

BAFANG DP C10.CAN Manuel utilisateur

BAFANG

BAFANG BT C01.340.UART Guide de référence

BAFANG

BAFANG H310 Manuel utilisateur

BAFANG

BAFANG C965 Manuel utilisateur

BAFANG

BAFANG DP E161.CAN Manuel utilisateur

BAFANG

BAFANG M510 Manuel utilisateur

BAFANG

BAFANG C961 Manuel utilisateur

Manuels Accessoires pour vélos populaires d'autres marques

Sigma

Sigma BC 16.16 Manuel utilisateur

Playcore

Playcore Dero Setbacks Manuel utilisateur

VDO Cyclecomputing

VDO Cyclecomputing x3dw Manuel utilisateur

Cateye

Cateye RAPID X2 Manuel utilisateur

buratti meccanica

buratti meccanica Clorofilla Trail Manuel utilisateur

Shimano

Shimano SG-8R20 Mode d'emploi

BOB

BOB YAK Manuel utilisateur

APLIC

APLIC 303303/20190717TW012 Manuel utilisateur

SRAM

SRAM AXS BlipBox Manuel utilisateur

Garmin

Garmin EDGE 500 Manuel utilisateur

Shimano

Shimano FD-RX810 Manuel utilisateur

Cateye

Cateye V2C - Manuel d'instructions

KMART

KMART 43115907 Manuel utilisateur

SIGMA SPORT

SIGMA SPORT Buster 2000 Manuel utilisateur

NVO Components

NVO Components STEM Manuel utilisateur

DAXYS

DAXYS BP188 Manuel utilisateur

XLC

XLC BV-W17 Manuel utilisateur

Deda Elementi

Deda Elementi SUPERBOX Manuel utilisateur