B-K lighting MINI-MICRO DRIVESTAR Manuel utilisateur

MINI-MICRO™ DRIVESTAR™

Surface Mount Installation

RELEASED

11-21-16

REFERENCE NUMBER

INS001068.1

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

NEEDED

FOR

INSTALLATION:

5/64” Allen Wrench

Waterproof Wire Connectors

Warning Flammable Hot Surface

Faceplate

BKSSL

Power Pipe™

Collar

Stability Flange

Body

Power Pipe™

Surface mount collar

Stability Flange

Faceplate

Body

Temporary cover

18 gauge wire

By Others

· Suitable for wet locations · Not suitable for through wiring

IMPORTANT LISTINGS AND CERTIFICATIONS

Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.

Please refer to the low voltage

design guide at www.bklighting.

com/lvguide before installation for

proper wire selection.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local and

Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective

equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and

lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause an

unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part, as

this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body.

• Replace LED assembly only with correct wattage and type of

power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause an

unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.

Fixture gets HOT quickly! Contact only switch/plug when

turning on. Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time. Use

a soft cloth or gloves. Oil from skin may cause damage.

SAVE THESE INSTRUCTIONS

RELEASED

11-21-16

REFERENCE NUMBER

INS001068.1

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

PROJECT:

TYPE:

MINI-MICRO ™ DRIVESTAR™

Surface Mount Installation

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

1. Excavate trench according to designed lighting

plan 10” deep and 10” wide suitable for the 8-3/4”

fixture housing.

2. Supply low voltage wiring necessary for

installation (By Others).

3. Slide stability flange onto Power Pipe™.

NOTE: Product is supplied with a stability

flange to anchor fixture and aid in installation.

Do not cut Power Pipe™. Doing so will

prevent sufficient wire makeup for fixture

service and will void warranty.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

4. Loop minimum of 6” of low voltage wire inside

Power Pipe™ to allow for fixture service.

NOTE: Do not remove temporary cover!

5. Place Power Pipe™ in hole.

NOTE: Leave sufficient wire length in the

Power Pipe™ for future service.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

6. Align holes to final installation orientation. Point

arrows on temporary cover toward surface to be

illuminated.

NOTE: Do not remove temporary cover until

installation of faceplate.

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

7. Back fill with pea gravel or sand prior to pour.

NOTE: The Power Pipe™ must be flush to

finished grade. Use stability flange to aid in

installation of Power Pipe™ as shown.

Soil Prep

Conduit

trench

B. Dig hole 10” wide and 10” deep.

Conduit

Trench

Excavated

for Housing

C. Prep soil according to DIG-IT Guide.

A. Determine Soil Type by referencing DIG-IT Guide.

Prep soil according to DIG-IT Guide.

Fixture Installation

RELEASED

11-21-16

REFERENCE NUMBER

INS001068.1

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

PROJECT:

TYPE:

MINI-MICRO ™ DRIVESTAR™

Surface Mount Installation

2. Pull the heat sink from the body to expose

the LED board and Driver components. Utilize

quick disconnects to change modular LED

and driver components. Re-install the heat

sink into body.

1. Loosen #8-32 set screw on faceplate assembly

using a 5/64” Allen wrench and remove.

Loosen set screw on collar and remove.

COMPONENT REPLACEMENT - IF REQUIRED

THIS PRODUCT IS AVAILABLE WITH A FACTORY INSTALLED LED.

3. Replace faceplate assembly and tighten set

screw. Re-Install fixture.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Faceplate

BKSSL

Power Pipe™

Collar

Stability Flange

Body

Power Pipe™

Surface mount collar

Stability Flange

Temporary cover

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Faceplate

BKSSL

Power Pipe™

Collar

Stability Flange

Body

Power Pipe™

Surface mount collar

Stability Flange

Temporary cover

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

10. Mount faceplate to collar using (2) #6-32x5/8”

flat head screws (provided) with a 5/64” Allen

wrench.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

8. Remove temporary cover and pull out low

voltage wire.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

WIRING DIAGRAM

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

2 window

faceplate

shown

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade

Concrete

8. Remove temporary cover and pull out low

voltage wire.

Wire nuts must

clear opening

6”

min.

Finished grade

6”

min.

Finished grade

Wire nuts must

clear opening

6”

min.

Finished grade

8 3/4”

9. Access low voltage wire inside Power Pipe™. Make

two watertight connections using waterproof

wire connectors (By Others). Wire nuts must clear

opening. Insert fixture and low voltage wire into

Power Pipe™.

Table des matières

Autres manuels B-K lighting Équipement d'éclairage

B-K lighting

B-K lighting Mini-Micro Series Manuel utilisateur

B-K lighting

B-K lighting Union Bollard Manuel utilisateur

B-K lighting

B-K lighting CORE DRILL Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

B-K lighting

B-K lighting BACK BOX Manuel utilisateur

B-K lighting

B-K lighting YOSEMITE Series Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Integral Manuel utilisateur

B-K lighting

B-K lighting TETON Manuel utilisateur

B-K lighting

B-K lighting Path Star Manuel utilisateur

B-K lighting

B-K lighting RE1 Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Series Manuel utilisateur

B-K lighting

B-K lighting MB2 Manuel utilisateur

B-K lighting

B-K lighting Union Bollard Manuel utilisateur

B-K lighting

B-K lighting ORION Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Remote Manuel utilisateur

B-K lighting

B-K lighting Denali Series Manuel utilisateur

B-K lighting

B-K lighting SQUARE ADJUSTABLE WELL STAR Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Remote ES16 Metal Halide Manuel utilisateur

B-K lighting

B-K lighting PRECISION2 CO2 Series Manuel utilisateur

B-K lighting

B-K lighting SS Manuel utilisateur

B-K lighting

B-K lighting MICRO NITE STAR Manuel utilisateur

B-K lighting

B-K lighting Altair Manuel utilisateur

B-K lighting

B-K lighting HP2RM Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur