B-K lighting Path Star Manuel utilisateur

PRELIMINARY

12-19-11

REFERENCE NUMBER

INS000891

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

PS™ /BS™/ PSL™/ BSL™

Installation Instructions

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

This set of instructions works for:

PS - Path Star™

BS - Bollard Star™

PSL - Louvered Path Star™

BSL - Louvered Bollard Star™

Warning High Voltage Hot Surface

TECHNOLO

with

TOOLS

MATERIALS

NEEDED:

1/8” Allen wrench

Phillips screwdriver

Mounting hardware

Wire connectors

(recommended silicone filled wire connectors)

Drill

By Others

Anchor Base

18 Gauge

Wire

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local

and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping of

this product.

• Before wiring to power supply and during servicing or relamping,

turn off power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause

an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part,

as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body. Do not touch the lamp at any time. Use

a clean, dry, soft cloth to handle the lamp. Oil from skin may

damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp

marked on fixture label.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause an

unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted lamp is HOT!

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing lamp.

Lamp gets HOT quickly! Contact only switch/plug when

turning on.

Do not touch hot lens, guard, or enclosure (see diagram/

picture).

Keep lamp away from materials that may burn.

Do no touch the lamp at any time. Use a soft cloth. Oil

from skin may damage lamp.

Do not operate the luminaire fitting with a missing or

damaged shield.

SAVE THESE INSTRUCTIONS

· Suitable for wet locations

IMPORTANT LISTINGS AND CERTIFICATIONS

PSL

BSL

Remote Transformer

5. Make two connections from remote 12V

transformer to LED source leads (18 gauge

wire) using proper wire connectors (By Others).

See wiring diagram.

4. Pull low voltage wire to anchor base.

7. Place fixture on anchor base and tighten four

(4) #10-32 stainless steel button head cap

screws using a 1/8” Allen wrench.

Anchor Base Installation

120V 12V

Fixture

COM

Remote

Transformer

COM

120V 12V

Fixture

COM

GROUND

Integral

Transformer

COM

GROUND IN HOUSING

Integral Transformer

6. Pull branch circuit wires neccessary for

installation (By Others) through anchor base.

Anchor base can accomodate up to two (2)

1/2” conduits. Use proper wire connectors

(By Others) to connect transformer primary

leads to branch circuit wires. Connect incoming

ground to ground wire provided in fixture

body. See wiring diagram.

Wiring diagram.

Integral Transformer

Remote Transformer

1. Determine suitable anchors (By Others) to

attach anchor base to architectural surface.

2. Place provided template in final mounting

position according to designed lighting plan.

3. Drill holes into surface for maximum 7/16”

fasteners (By Others) on locations illustrated on

template.

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

PROJECT:

TYPE:

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

3167387

ETL LISTED

CONFORMS TO ANSI/UL STANDARD 1838,

CERTIFIED TO CSA STD C22.2 NO.250.7

CSA STD C22.2 TIL B-58A

PS™ /BS™/PSL™/ BSL™

Installation Instructions

TECHNOLO

with

PRELIMINARY

12-19-11

REFERENCE NUMBER

INS000891

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

PROJECT:

TYPE:

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

3167387

ETL LISTED

CONFORMS TO ANSI/UL STANDARD 1838,

CERTIFIED TO CSA STD C22.2 NO.250.7

CSA STD C22.2 TIL B-58A

PS™ /BS™/PSL™/ BSL™

Installation Instructions

TECHNOLO

with

PRELIMINARY

12-19-11

REFERENCE NUMBER

INS000891

To Change Lumen Output (when required).

1. Use 1/8” Allen wrench to loosen #10-24

stainless faceplate screws to remove faceplate.

3. Re-place faceplate.

2. With flat head screw driver rotate dial to

desired lumen output.

This product is available with Adjust-e-Lume™ (Patent Pend.) for Dynamic Lumen Output Control

Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set

to the appropriate light level desired during installation.

3 1/2"

1 1/2"

4 X

7/16" Dia.

NOTES: Full Scale Anchor Bolt Template

DRAWING NUMBER

BASE,PS,MACH,ALU

511085

5/15/08

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING AND ITS RECEIPT OR POSSESSION

DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR

SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN

AUTHORIZATION OF B-K LIGHTING IS STRICTLY FORBIDDEN.

WARNING!

Template must print at proper scale.

Verify dimensions prior to use.

Ce manuel convient aux modèles suivants

Autres manuels B-K lighting Équipement d'éclairage

B-K lighting

B-K lighting ORION Manuel utilisateur

B-K lighting

B-K lighting MICRO NITE STAR Manuel utilisateur

B-K lighting

B-K lighting RE1 Manuel utilisateur

B-K lighting

B-K lighting HP2RM Manuel utilisateur

B-K lighting

B-K lighting LT Manuel utilisateur

B-K lighting

B-K lighting ORION Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Remote ES16 Metal Halide Manuel utilisateur

B-K lighting

B-K lighting TETON Manuel utilisateur

B-K lighting

B-K lighting PRECISION2 CO2 Series Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Integral Manuel utilisateur

B-K lighting

B-K lighting BACK BOX Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Remote Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Series Manuel utilisateur

B-K lighting

B-K lighting PS Manuel utilisateur

B-K lighting

B-K lighting Union Bollard Manuel utilisateur

B-K lighting

B-K lighting MINI-MICRO RECESSED UPLIGHT Manuel utilisateur

B-K lighting

B-K lighting BKSSL Precision2 DR2 Series Manuel utilisateur

B-K lighting

B-K lighting Nite Star Manuel utilisateur

B-K lighting

B-K lighting YOSEMITE Series Manuel utilisateur

B-K lighting

B-K lighting Denali Series Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

B-K lighting

B-K lighting SS Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur