B-K lighting MINI-MICRO RECESSED UPLIGHT Manuel utilisateur

MINI-MICRO ™ RECESSED UPLIGHT

Flush Mount Installation

RELEASE DATE

12-13-16

REFERENCE NUMBER

INS000933

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY

DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

5/64” Allen Wrench

Waterproof Wire Connectors

Please refer to the low

voltage design guide at www.

bklighting.com/lvguide before

installation for proper wire

selection.

TOOLS

NEEDED:

By Others

Warning Low Voltage Hot Surface

· Suitable for wet locations · Suitable for in ground installations

IMPORTANT LISTINGS AND CERTIFICATIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

Dia.

(56mm)

(32mm)

1 1/4"

(191mm)

7 1/2"

2 1/4"

8 3/4"

(222mm)

(42mm)

1 5/8" Dia.

(56mm)

8 3/4"

(222mm)

(32mm)

1 1/4"

Dia.2 1/4"

7 1/2"

(191mm)

(42mm)

1 5/8" Dia.

6" Dia.

(152mm)

2 1/4" Dia.

(57mm)

1 1/2" O.C.

(38mm)

7/8"

(152mm)

(22mm)

Concrete

Pour Collar

5’

(1524mm)

18 Ga.

2 low voltage

direct burial

cable

PVC Housing

Stability Flange

Body

Faceplate

18 Ga. Wire

Flush Mount

Collar

Flammable

Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all Local and

Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective

equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and

lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an

unsafe condition. The use of damaged components may cause an

unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part, as

this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body.

• Replace LED assembly only with correct wattage and type of

power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean

during installation and service; failure to do this may cause an

unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.

Fixture gets HOT quickly! Contact only switch/plug when

turning on. Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time. Use

a soft cloth or gloves. Oil from skin may cause damage.

SAVE THESE INSTRUCTIONS

7. Per DIG-IT Guide, backfill the gap between the

bottom of housing and bottom of hole with

sand or pea gravel for drainage.

NOTE: The mounting collar must be flush to

finished grade. Use stability flange to aid in

installation as shown.

5. Place Power Pipe™ in hole.

NOTE: Leave sufficient wire length in the

Power Pipe™ for future service.

RELEASE DATE

12-13-16

REFERENCE NUMBER

INS000933

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Dia.

(56mm)

(32mm)

1 1/4"

(191mm)

7 1/2"

2 1/4"

8 3/4"

(222mm)

(42mm)

1 5/8" Dia.

(56mm)

8 3/4"

(222mm)

(32mm)

1 1/4"

Dia.2 1/4"

7 1/2"

(191mm)

(42mm)

1 5/8" Dia.

6" Dia.

(152mm)

2 1/4" Dia.

(57mm)

1 1/2" O.C.

(38mm)

7/8"

(152mm)

(22mm)

Concrete

Pour Collar

5’

(1524mm)

18 Ga.

2 low voltage

direct burial

cable

MINI-MICRO™ RECESSED UPLIGHT

Flush Mount Installation

Arrows on temporary

cover indicate screw

pattern for faceplate

attachement

Temporary cover

Faceplate

BKSSL

Power Pipe™

Concrete Pour collar

Stability Flange

Body

6. Orient the arrows on the temporary cover to

the desired position of the final faceplate screw

placement.

NOTE: DO NOT remove temporary cover until

installation of faceplate.

3. Slide stability flange onto Power Pipe™.

NOTE: Product is supplied with a stability

flange to anchor fixture and aid in installation.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

1. Excavate trench according to designed lighting

plan 10” deep and 10” wide suitable for the 8-3/4”

fixture housing.

2. Supply low voltage wiring necessary for

installation (By Others).

4. Loop 12” of low voltage wire inside Power

Pipe™.

Note: DO NOT remove temporary cover!

Soil Prep

Conduit

trench

B. Dig hole 10” wide and 10” deep.

Conduit

Trench

Excavated

for Housing

C. Prep soil according to DIG-IT Guide.

Fixture Installation

A. Determine Soil Type by referencing DIG-IT Guide.

Prep soil according to DIG-IT Guide.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

9. Remove temporary cover and pull out low

voltage wire.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

11. Mount faceplate to collar using (2) #6-32 screws

(provided) with a 5/64” Allen wrench.

WIRING DIAGRAM

LED - For use with 12VAC remote

transformer or magnetic transformers only.

B-K Lighting cannot guarantee performance

with third party manufacturers’

transformers.

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

8. Fill the hole around the fixture housing to

12” below the finished grade with clean fill dirt

and tamp carefully to prevent settling of fixture.

Pour concrete and finish as required flush with

mounting collar.

NOTE: The mounting collar must be flush to

finished grade. Use stability flange to aid in

installation as shown.

Dia.

(56mm)

(32mm)

1 1/4"

(191mm)

7 1/2"

2 1/4"

8 3/4"

(222mm)

(42mm)

1 5/8" Dia.

(56mm)

8 3/4"

(222mm)

(32mm)

1 1/4"

Dia.2 1/4"

7 1/2"

(191mm)

(42mm)

1 5/8" Dia.

6" Dia.

(152mm)

2 1/4" Dia.

(57mm)

1 1/2" O.C.

(38mm)

7/8"

(152mm)

(22mm)

Concrete

Pour Collar

5’

(1524mm)

18 Ga.

2 low voltage

direct burial

cable

MINI-MICRO™ RECESSED UPLIGHT

Flush Mount Installation

RELEASE DATE

12-13-16

REFERENCE NUMBER

INS000933

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

Finished grade

8 3/4”

2 window

faceplate

shown

Finished grade

8 3/4”

LINE 12V

FIXTURE

COM

Remote

Transformer

COM

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Optical opening on

faceplate will align with

alignment arrows on

temporary cover

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Stability flange

Rebar or stake (by others)

Pea gravel or sand

Finished grade

Concrete

Finished grade Concrete

Wire nuts must

clear opening

6”

min.

10. Access low voltage wire inside Power Pipe™.

Make two watertight connections using

waterproof wire connectors (By Others). Wire

nuts must clear opening. Insert fixture and

low voltage wire into housing. See wiring

diagram.

Table des matières

Autres manuels B-K lighting Équipement d'éclairage

B-K lighting

B-K lighting MINI-MICRO DRIVESTAR Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Series Manuel utilisateur

B-K lighting

B-K lighting SIGN STAR Series Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Remote Manuel utilisateur

B-K lighting

B-K lighting Denali Series Manuel utilisateur

B-K lighting

B-K lighting BKSSL Precision2 DR2 Series Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Integral Manuel utilisateur

B-K lighting

B-K lighting Union Bollard Manuel utilisateur

B-K lighting

B-K lighting SQUARE ADJUSTABLE WELL STAR Manuel utilisateur

B-K lighting

B-K lighting INTEGRAL DENALI Series Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

B-K lighting

B-K lighting Altair Manuel utilisateur

B-K lighting

B-K lighting CORE DRILL Manuel utilisateur

B-K lighting

B-K lighting ORION Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Remote ES16 Metal Halide Manuel utilisateur

B-K lighting

B-K lighting Mini-Micro Series Manuel utilisateur

B-K lighting

B-K lighting YOSEMITE Series Manuel utilisateur

B-K lighting

B-K lighting MB2 Manuel utilisateur

B-K lighting

B-K lighting PRECISION2 CO2 Series Manuel utilisateur

B-K lighting

B-K lighting RE1 Manuel utilisateur

B-K lighting

B-K lighting TETON Manuel utilisateur

B-K lighting

B-K lighting LT Manuel utilisateur

B-K lighting

B-K lighting HP2RM Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur