B-K lighting Altair Manuel utilisateur

RELEASE DATE

01/24/2022

REFERENCE NUMBER

INS-2577-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR

SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the

National Electrical Code, Canadian Electrical Code, and all

Local and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping

of this product.

• Before wiring to power supply and during servicing or

relamping, turn off power at fuse or circuit breaker before

service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause

an unsafe condition. The use of damaged components may

cause an unsafe condition and void product warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part,

as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.

Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body. Do not touch the lamp at any time. Use

a clean, dry, soft cloth to handle the lamp. Oil from skin

may damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp

marked on fixture label.

• All gaskets, o-rings and sealing surfaces must be kept

clean during installation and service; failure to do this may

cause an unsafe condition and void product warranty.

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY

TO PERSONS IMPORTANT

SAFETY INSTRUCTIONS

Lighted fixture is HOT!

WARNING - To reduce the risk of

FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before

replacing lamp/LED. Fixture gets HOT quickly!

Contact only switch/plug when turning

on. Do not touch hot lens, guard, or enclosure.

Keep fixture away from materials that may burn.

Do not operate the luminaire fitting with a missing or

damaged shield. Do not touch the source at any time.

Use a soft cloth or gloves. Oil from skin may cause

damage.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION

INSTRUCTIONS

ALTAIR

YOKE MOUNT

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations

Standard Installation

Warning Hot Surface High Voltage

ALTAIR - YOKE MOUNT

TOOLS

NEEDED:

Waterproof Wire Connectors

Mounting Hardware

Adjustable Crescent Wrench

Torx 27 Tamper-Proof Wrench

Heavy-Gauged, Die-Formed

Aluminum Housing

Anti-Tamper

Fasteners

Gasketed Door

and Lens

Yoke

Weather-tight Connector

with Built-in Strain Relief

Integral Driver (Interior)

16/5 STW Cord

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

RELEASE DATE

01/24/2022

REFERENCE NUMBER

INS-2577-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO

MANUFACTURE, USE OR SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

ALTAIR

YOKE MOUNT

Standard Installation

2. Line up fixture yoke to mounting location and

secure with 3/4-10 hex bolt with adjustable

crescent wrench.

Yoke Mount Installation

1. Prepare for installation for yoke location.

Clearance hole is 9/16” diameter.

9/16” Dia.

WIRING DIAGRAM

3. Make watertight connections using waterproof

wire connectors to connect incoming primary

wiring to integral driver wiring as per NEC.

Secondary side is factory wired. See wiring

diagram.

HOT LED

NEUTRAL

GROUND

HOT

NEUTRAL

GROUND

Integral

DRIVER

0-10V -

0-10V +

0-10V -

0-10V +

ALTAIR

LED

Relamping Instructions

2. Prepare to remove LED board, thermal pad

and heatsink by loosening six (6) #8-32 slotted

screws using a 1/4 nut driver/socket wrench or

a flat head screwdriver.

1. Remove faceplate by loosening four (4)

tamper-resistant hex screws using a Torx T27

tamper resistant hex bit.

3. Use quick disconnect to disconnect heatsink

and LED board from driver.

5. If replacing LED driver: Turn off branch

circuit. Disconnect wire nuts from incoming

primary to primary side of driver.

6. Remove two (2) #10-24 hex nuts from driver

bracket using a 5/16 nut driver with socket.

Replace with new driver and reinstall driver

bracket.

Connect incoming primary to driver primary

leads for correct incoming voltage.

4. If replacing LED board: Remove LED board

and thermal pad from heatsink by loosening

sixteen (16) Phillips screws using Phillips

screwdriver. Line up new thermal pad and

LED board on heatsink. Replace board and

thermal pad on heatsink with thermal pad

closest to heatsink, then reverse install.

7. Reconnect quick disconnect from driver

secondary side to LED board assembly.

TOOLS

NEEDED:

Torx T27 Tamper Resistant Hex Bit

1/4 Nut Driver/Socket Wrench

5/16 Nut Driver/Socket Wrench

Phillips Screwdriver

Flat Head Screwdriver

8. Secure LED board and heatsink by tightening

six (6) #8-32 slotted screws using a 1/4 nut

driver/socket wrench or flat head screw driver.

9. Replace faceplate by tightening four (4)

tamper-resistant hex screws using a Torx T27

tamper resistant hex bit.

IMPORTANT SAFETY

INFORMATION - READ,

FOLLOW, AND SAVE ALL

SAFETY AND INSTALLATION

INSTRUCTIONS

• Product must be installed by a qualified person

in a manner consistent with its intended use

and in compliance with the National Electrical

Code, Canadian Electrical Code, and all Local

and Provincial Codes.

• Follow product label information and

instructions.

• Qualified Personnel must perform all servicing

or relamping of this product.

• Before wiring to power supply and during

servicing or relamping, turn off power at fuse

or circuit breaker before service.

Hot SurfaceHigh VoltageWarning

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

RELEASE DATE

01/24/2022

REFERENCE NUMBER

INS-2473-00

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.bklighting.com • [email protected]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO

MANUFACTURE, USE OR SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

Autres manuels B-K lighting Équipement d'éclairage

B-K lighting

B-K lighting BKSSL Precision2 DR2 Series Manuel utilisateur

B-K lighting

B-K lighting BACK BOX Manuel utilisateur

B-K lighting

B-K lighting Mini-Micro Series Manuel utilisateur

B-K lighting

B-K lighting TETON Manuel utilisateur

B-K lighting

B-K lighting SQUARE ADJUSTABLE WELL STAR Manuel utilisateur

B-K lighting

B-K lighting MB2 Manuel utilisateur

B-K lighting

B-K lighting YOSEMITE Series Manuel utilisateur

B-K lighting

B-K lighting RE1 Manuel utilisateur

B-K lighting

B-K lighting ArtiStar Integral Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

B-K lighting

B-K lighting DENALI Manuel utilisateur

B-K lighting

B-K lighting ORION Manuel utilisateur

B-K lighting

B-K lighting Nite Star Manuel utilisateur

B-K lighting

B-K lighting MICRO NITE STAR Manuel utilisateur

B-K lighting

B-K lighting SS Manuel utilisateur

B-K lighting

B-K lighting Denali Series Manuel utilisateur

B-K lighting

B-K lighting Union Bollard Manuel utilisateur

B-K lighting

B-K lighting SIGN STAR Series Manuel utilisateur

B-K lighting

B-K lighting Path Star Manuel utilisateur

B-K lighting

B-K lighting Precision2 HP2 Series Manuel utilisateur

B-K lighting

B-K lighting PRECISION2 CO2 Series Manuel utilisateur

B-K lighting

B-K lighting ORION Manuel utilisateur

B-K lighting

B-K lighting LT Manuel utilisateur

B-K lighting

B-K lighting INTEGRAL DENALI Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur