Aztech WL635USB Manuel utilisateur

WL635USB Wireless B/G

USB 2.0 Adaptor

User Manual

Version 1.1

CONTENTS

1 INTRODUCTION TO WL635USB WIRELESS B/G USB 2.0 ADAPTOR ................................3

1.1 PACKAGE CONTENTS....................................................................................................................3

1.2 FEATURES .....................................................................................................................................3

1.3 LED INDICATORS..........................................................................................................................4

2 INSTALLATION ................................................................................................................................. 5

2.1 SYSTEM REQUIREMENTS..............................................................................................................5

2.2 STEP 1: INSTALL THE DRIVER & UTILITY......................................................................................5

2.3 STEP 2: INSTALL THE DEVICE.......................................................................................................7

2.4 VERIFY INSTALLATION...................................................................................................................9

2.5 UNINSTALLATION...........................................................................................................................9

3 NETWORK CONNECTION ............................................................................................................10

3.1 IN WINDOWS 98SE/ME..............................................................................................................10

3.2 IN WINDOWS 2000/XP ...............................................................................................................11

4 IP ADDRESS ....................................................................................................................................12

5 CONFIGURATION UTILITY...........................................................................................................13

5.1 MAIN TAB ....................................................................................................................................14

5.2 PROFILE MANAGER TAB .............................................................................................................19

5.3 INFORMATION TAB ......................................................................................................................20

6 EXAMPLE OF CONNECTION TO AN ACCESS POINT...........................................................21

Product warranty does not apply to damage caused by lightning, power surges or wrong voltage usage.

Declaration of Conformity

FCC Certification

The United States Federal Communication Commission (FCC) and the Canadian Department

of Communications have established certain rules governing the use of electronic equipment.

Part15, Class B

This device complies with Part 15 of FCC rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interface, and

2) This device must accept any interface received, including interface that may cause

undesired operation. This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy, and if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

CAUTION:

1. To comply with FCC RF exposure compliance requirements, a separation distance of at

least 20 cm must be maintained between the antenna of this device and all persons.

2. This transmitter must not be co-located or operating in conjunction with any other antenna

or transmitter.

1 Introduction to WL635USB Wireless B/G USB 2.0 Adaptor

The WL635USB Wireless B/G USB 2.0 Adaptor is designed for creating a wireless

workstation for notebook or desktop computer. It is compatible with any USB-equipped

computers. The WL 635USB Wireless B/G USB 2.0 Adaptor is compliant with both Wireless-

G (802.11g) and Wireless-B (802.11b).

WL635USB is based on Texas Instruments’ (TI) G++ Turbo mode (125Mbps equivalent)

performance enhancing technology and by incorporating USB 2.0, the adaptor connects to

wireless network at incredible speeds and delivers blazing fast data rates up to 125 Mbps*.

An example of 125Mbps* Wireless LAN set up will be Aztech WL635USB (TI chipset) +

DSL600EW (TI chipset).

1.1 Package Contents

Make sure that you have the following items. If any of the items is damaged or missing,

please contact your dealer immediately.

WL635USB Wireless B/G USB 2.0 Adaptor (Qty:1) Easy Start (Qty:1)

Installation CD (Qty:1) USB Extension Cable (Qty:1)

1.2 Features

• Complies with IEEE 802.11g standard for 2.4GHz Wireless LAN

• USB 2.0 compliant

• USB Plug & Play

• Interoperable with existing network infrastructure

• Secure information transmission

• Freedom to roam while staying connected

• Compatible with specialty wireless products and services

• Up to 125Mbps∗data rate

• Antenna is built in the card with LED indication

• Low power consumption

• Easy to install and configure

(

∗

Applicable to Texas Instruments end-to-end chipsets Wireless LAN solution. Maximum

wireless signal rate derived from IEEE Standard 802.11g specifications and does not

represent actual data throughput. Network conditions and environmental factors, including

volume of network traffic, building materials and construction, and network overhead, lower

actual data throughput rate)

1.3 LED Indicators

Power Indicator (Green LED):

The LED will light up when the device is connected to a network (an AP or Peer-to-Peer).

The LED will blink when the device is scanning for all available networks.

Act Indicator (Green LED):

The LED will flicker when there is transmitting/receiving of wireless data.

2 Installation

2.1 System Requirements

• Desktop PC or Notebook PC

• Pentium® 233 processor or higher

• 128MB RAM

• 20MB hard disk space (system files and modem driver only)

• A free USB Port

• CD-ROM drive

• Windows® 98 SE / Windows® Me / Windows® XP / Windows® 2000

2.2 Step 1: Install the Driver & Utility

Caution!!!

Do not insert the wireless LAN card

into your computer until the

procedures in “ Install the Device &

Utility ” have been performed.

Important Note:

Connect to an USB 2.0 USB host to have maximum rate of 54Mbps

(802. 11g).

If connected to an USB 1.1 USB host, the maximum rate will be 11 Mbps

(802.11b) only.

1. Exit all Windows programs. Insert the Installation CD into your CD-ROM. The CD will run

automatically. If the Installation CD auto run fails, please run the “Setup.exe” file in the

CD.

For Windows 98SE/ME/2000/XP

2. When the Welcome screen appears, click “Next” to continue.

3. The below screen will be shown. Click “Next” to continue.

4. The below screen will be shown. Click “Next” to continue and the installation program

will start running automatically.

5. For Windows 2000 and Windows XP, you may be prompted for Digital Signature not

found. Just click “Yes” or “Continue Anyway” to continue with the installation.

6. When the below screen is shown, click “Finish” to restart the system.

2.3 Step 2: Install the Device

Note: Before you install the device to your computer, make sure you have

installed the driver and utility as described in the previous section.

1. Locate your USB host and insert the USB 2.0 Adaptor.

2. Once the device has been inserted to your computer,

Windows will detect the new hardware.

3. Windows will begin copying the files to your computer.

For Windows 98SE/ME

4. Before installing the device, make sure you have your original Windows 98 CD-ROM on

hand (not required for Windows ME). When the prompt for “Windows 98 Second Edition

CD-ROM” window appears, insert the CD-ROM as requested. Click “OK” to continue the

installation.

5. The installation will continue and the system may prompt for a “Version Conflict”. Click

“Yes” to keep the existing file. This completes the installation of the device.

For Windows 2000

4. When the “Digital Signature Not Found” screen appears, click “Yes” to continue the

installation.

5. This completes the installation of the device.

Page 8 of 22

For Windows XP

4. Windows may ask to connect to Windows Update to search for software. Select “No”.

When below is prompted, click “Next” to continue the installation.

hen the “Hardware Installation” screen appears, click “Continue Anyway” to continue

. When the following screen appears, click “Finish” to complete the installation of the

evice.

5. W

the installation.

2.4 Verify Installation

To verify if the device exists in your computer and works, go to Start ÆSettings ÆControl

Panel ÆSystem ÆHardware ÆDevice Manager. Expand the Network Adaptors

category. If the WL635USB Wireless B/G USB Adapter is listed here, it means that your

device is properly installed and enabled.

.5 Uninstallation2

. To uninstall the driver and utility, go to the Control Panel of your system.

G Utility in the Add/Remove Programs and

tions to uninstall the driver and utility. After the uninstallation,

2. Open the Add/Remove Programs.

3. Select the WL635USB Wireless B+

then click on the Remove.

4. Follow the on screen instruc

plug out the device and reboot the system.

3 Network Connection

Once the device driver is well installed, a network setting described in the following should be

also established.

3.1 In Windows 98SE/ME

1. Go to Start ÆSettings ÆControl Panel ÆNetwork.

Make sure that all the required components are installed. If any components are missing,

click on the “Add”button to add them in.

2. For making your computer visible on the network, enable the “File and Print Sharing…”

and check on the boxes as shown.

3. Click the “Identification” tab. Make up a name that is unique from the other computers'

names on the network. Type the name of your workgroup, which should be the same

used by all of the other PCs on the network.

Table des matières

Autres manuels Aztech Adaptateur

Aztech

Aztech WL230USB Wireless B+G Manuel utilisateur

Aztech

Aztech 200Mbps HomePlug AV Ethernet Adaptor Manuel utilisateur

Aztech

Aztech WL558USB Manuel utilisateur

Aztech

Aztech 500Mbps HomePlug AV Manuel utilisateur

Aztech

Aztech HomePlug AV Manuel utilisateur

Aztech

Aztech HomePlug Turbo Fiche d'information produit

Aztech

Aztech HomePlug Mediaxtream Ethernet Adapter Manuel utilisateur

Aztech

Aztech WL592USB Manuel utilisateur

Aztech

Aztech WL592USB Instructions d'utilisation

Aztech

Aztech WL230USB Wireless B+G Instructions d'utilisation

Aztech

Aztech HL129EP Instructions d'utilisation

Aztech

Aztech HL112E Mode d’emploi

Aztech

Aztech WL582USB Instructions d'utilisation

Aztech

Aztech WL562 Manuel utilisateur

Aztech

Aztech HomePlug AV Manuel utilisateur

Aztech

Aztech WL230USB Wireless B+G Manuel utilisateur

Aztech

Aztech HL117E Instructions d'utilisation

Aztech

Aztech WL558USB Manuel utilisateur

Aztech

Aztech Easy Mode d’emploi

Aztech

Aztech HL113 E Manuel utilisateur

Aztech

Aztech WL578USB Instructions d'utilisation

Aztech

Aztech WL568USB Manuel utilisateur

Aztech

Aztech Wireless N USB Adapter Manuel utilisateur

Aztech

Aztech Wireless N USB Adapter Instructions d'utilisation

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur