AXIOMTEK GOT-2770S Manuel utilisateur
GOT-2770S
7.7” DSTN LCD, Xscale-based touch screen
computer
User’s Manual
Disclaimers
The information in this manual has been carefully checked and is
believed to be accurate. AXIOMTEK Co., Ltd. assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be
contained in this document. AXIOMTEK makes no commitment to update or to
keep current the information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of
AXIOMTEK Co., Ltd.
Copyright 2003 by AXIOMTEK Co., Ltd.
All rights reserved.
Nov. 2003,
Printed in Taiwan
Edition V1.00
ii
ESD Precautions
Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:
Do not remove boards or integrated circuits from their anti-static
packaging until you are ready to install them.
Before handling a board or integrated circuit, touch an unpainted
portion of the system unit chassis for a few seconds. This helps to
discharge any static electricity on your body.
Wear a wrist-grounding strap, available from most electronic
component stores, when handling boards and components.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM is a registered trademark of International Business
Machines Corporation.
MS-DOS, Microsoft C and QuickBasic are trademarks of
Microsoft Corporation.
TURBO C is a trademark of Borland Inc.
BASIC is a trademark of Dartmouth College.
Intel is a trademark of Intel Corporation.
Other brand names and trademarks are the properties
and registered brands of their respective owners.
iii
Unpacking
The GOT-2770S is packed in an anti-static bag. The product has components
that are easily damaged by static electricity. Do not remove the anti-static
wrapping until proper precautions have been taken. Safety instructions in front
of this User’s Manual describe anti-static precautions and procedures.
After unpacking the product, place it on a raised surface and carefully inspect
the board for any damage that might have occurred during shipment. Ground
the product and exercise extreme care to prevent damage to the product from
static electricity.
Integrated circuits will sometimes come out of their sockets during shipment.
The GOT-2770S 7.7” DSTN LCD, Xscale-based touch screen computer
package includes the following:
GOT-2770S * 1
Driver CD *1
USB sync. cable *1
Touch pen * 1
Fuse * 1
Panel mount * 2
Make sure that all of the items listed above are present.
What To Do If There Is A Problem
If there are damaged or missing parts, contact your supplier and/or dealer
immediately. Do not attempt to apply power to the product if there is damage
to any of its components.
iv
Safety Instructions
Overview
This section states the safety instructions, which must be followed when
installing, operating and servicing the GOT-2770S. If neglected, physical injury
and death may follow, or damage may occur to controller and related
equipment. The material in this chapter must be studied before attempting any
work on, or with, the unit.
Warnings and Notes
This manual distinguishes safety instructions. Warnings are used to inform of
conditions, which can, if proper steps are not taken, lead to a serious fault
condition, physical injury or death. Notes are used when the reader is required
to pay special attention or when there is additional information available on the
subject. Notes are less crucial than warnings, but should not be disregarded.
Warnings Readers are informed of situations that can result in
serious physical injury and/or serious damage to
equipment with the symbol shown to the left. A Warning
symbol indicates that the reader should pay special
attention to the accompanying text. Precautionary steps
should be taken to insure that the installation is in
compliance with warnings. Warnings include hazardous
conditions that could cause personal injury or equipment
damage if care is not taken. The text next to this symbol
describes ways to avoid the danger.
Warnings Dangerous Voltage Warnings: Warns of situations in
which high voltage can cause physical injury and or
v
damage equipment.
General warning: Warns of situations, which can cause
physical injury and or damage equipment by means other
than electrical.
Electrostatic Discharge Warning: Warns of situations in
which an electrostatic discharge can damage equipment.
Readers are notified of the need for special attention or additional in formation
available on the subject with the following symbols:
CAUTION! Aims to draw special attention to it.
Note: Note: gives additional information or points out more
information available on the subject.
vi
Table of Contents
Disclaimers ------------------------------------------ ii
ESD Precautions --------------------------------- iii
Unpacking ------------------------------------------- iv
Safety Instructions -----------------------------v
Chapter 1 Introduction----------------------- 1
1.1 Introduction ------------------------------------------------ 1
1.2 Features ----------------------------------------------------12
1.3 Specifications---------------------------------------------- 2
Chapter 2 Installation Instructions--- 5
2.1 Mounting Instructions..........................................5
2.1.1 Location Considerations.......................... 5
2.1.2 Making a NEMA-4 Mounting.................... 5
2.1.3 Environmental Considerations ................ 6
2.2 Power Connections..............................................7
2.2.1 Power Requirements ................................ 8
2.2.2 Grounding Requirements ...................... 10
2.2.3 CE Requirements .................................... 10
2.2.4 Safety Guidelines ................................... 11
2.3 Communications Connections...........................13
2.3.1 Connector COM 1 [RS232] .................... 14
2.3.2 Connector COM2 [RS232] ..................... 15
2.3.3 Connector COM3 [RS422/485] .............. 16
2.3.4 USB Client port........................................ 17
2.3.5 USB Master port ...................................... 18
2.3.6 Dip Switch ............................................... 19
2.4 CE Requirements ...............................................20
2.5 Dimensions of GOT-2770S .................................21
Table of Contents vii
Chapter 3 Windows CE.NET --------------- 23
3.1 Introduction .......................................................23
3.2 Utilities...............................................................24
3.2.1 Soft-Keyboard ........................................ 24
3.2.2 System Settings ....................................... 25
3.2.3 IPSM ......................................................... 29
3.2.4 Startup..................................................... 30
3.2.5 Remote Desktop Connection (Windows
XP only) .................................................. 31
3.3 GOT-2770S Networking ......................................34
3.3.1 Networking via Ethernet ........................ 34
3.3.2 Networking via USB Client Port.............. 36
3.3.3 Web browser........................................... 38
3.4 Application program development ....................39
3.4.1 Microsoft eMbedded Visual C++ 4.0 .... 39
3.4.2 GOT-2770S SDK ....................................... 41
Appendix A Example Program ------------ 44
Table of Contents
viii
GOT-2770S User’s Manual
Chapter 1
Introduction
1.1 Introduction
The GOT-2770S series are fan-less and compact-size touch panel
computers. It equips with 7.7” DSTN LCD display, Windows CE.NET
and low power consumption CPU, Intel Xscale PXA255. Therefore,
GOT-2770S series are good cost-effective choices for operator
interface applications.
The GOT-2770S adopts most reliable and stable design. With fan-less
CPU and CompactFlash card, GOT-2770S is especially suitable for
vibration environment such as transportation, semiconductor etc. In
addition, GOT-2770S is also bundled with Windows CE.NET, which
forms a bridge that lets GOT-2770S be an open HMI solution for
system integration. Furthermore, GOT-2770S also supports Visual
Studio Framework 1.1. For connecting other devices, the GOT-2770S
provides several interfaces: USB, RS-232/422/485, Ethernet etc.
Introduction 1
GOT-2770S User’s Manual
1.2 Features
Fan-less and low power consumption CPU-Xscale PXA255
7.7” VGA color DSTN LCD
Windows CE.NET/ Visual Studio Framework 1.1 supported
and flash ROM on-board
Slim and compact size design
Suitable for reliable and vibration application – Fan less and
CompactFlash card
NEMA 4 / IP65 compliant front panel
Support USB 2.0 host and client
Over-voltage power protection – fuse
1.3 Specifications
Construction: plastic molding housing
Display: 7.7" VGA Color DSTN LCD
CPU and core logic: Intel™ PXA255
DRAM: 64 MB on board
Storage: 32 MB Flash memory on board,
1 CompactFlash™ card slot
I/O: 3 serial ports (COM1 RS-232, COM2: RS232, COM3:
RS422/485),
1 Ethernet port (10/100Base-T)
1 USB client for ActiveSync
2 USB Host ports
Sound output: 16 bit sound output
RTC: Built-in
Power input: 24 VDC, 0.5A maximum
Dimension (W x H x D): 231 x 176 x 55mm
Weight: 1.3kg
Introduction
2
Table des matières
Autres manuels AXIOMTEK écran tactile
Manuels écran tactile populaires d'autres marques
Elecro Engineering
Elecro Engineering Poolsmart Plus Instructions d'installation
Johnson Controls
Johnson Controls IQ4 HUB Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET2270L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET1002L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems 3201L Manuel utilisateur
Duratec
Duratec S15 Manuel utilisateur
