AXIOMTEK GOT-1120T Manuel utilisateur
GOT-1120T
Fanless Touch Panel Computer with
12.1" TFT LCD
User's Manual
Copyright notice
This document is copyrighted 2003 by AXIOMTEK Co., Ltd. All rights are
reserved. AXIOMTEK Co., Ltd. reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of
AXIOMTEK Co., Ltd. Information provided in this manual is intended to be
accurate and reliable. However, AXIOMTEK Co., Ltd. assumes no respon-
sibility for its use, nor for any infringements upon the rights of third parties
which may result from its use.
Acknowledgments
GOT-1120T is a trademark of AXIOMTEK Co., Ltd. IBM, PC/AT, and
PS/2 are trademarks of International Business Machines Corporation.
MS-DOS and Windows CE are trademarks of Microsoft Corporation.
All other brand and product names mentioned herein are trademarks or
registered trademarks of their respective holders.
Edition V1.0 Nov. 2003
Packing List
In the whole set of GOT-1120T there are items as listed below:
1. GOT-1120T x 1 unit
2. Accessory kit which includes:
(1) HDD cover screws x 4 pieces
(2) HDD cushions x 4 pieces
(3) Panel mounting clamper x 8 pieces
(4) Panel mounting screws x 8 pieces
(5) PC/104 plus expansion board standoff x 4 pieces
(6) 3-pin power connector x 1 piece
(7) GOT-1120T support CD x 1 piece
(8) 1 meter 9-pin to 9-pin null modem cable x 1 piece*1
FCC Class A
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy. If not installed and
used in accordance with this user's manual, it may cause harmful interference
to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense.
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this installation reference guide for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Do not use
liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the power outlet must be installed near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or
letting it fall could cause damage.
7. The openings on the enclosure are for air convection. Protect the equip-
ment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient over-voltage.
12. Never pour any liquid into an opening. This could cause fire or electrical
shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If any of the following situations arises, get the equipment checked by
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the installation reference guide.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -
20° C (-4° F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE
EQUIPMENT.
The sound pressure level at the operator's position according to IEC 704-1:1982
is equal to or less than 70 dB(A).
Table of Contents
Chapter1 General Information................................ 1
1.1 Introduction..................................................................... 2
1.2 Specifications ................................................................. 3
1.2.1 System kernel ................................................................. 3
1.2.2 I/O ports .......................................................................... 3
1.2.3 Storage ............................................................................ 4
1.2.4 Safety and environment .................................................... 4
1.3 LCD specifications ......................................................... 5
1.4 Touchscreen specifications........................................... 6
1.5 Power ............................................................................... 6
1.6 I/O ports arrangement .................................................... 6
1.7 Mounting.......................................................................... 7
1.7.1 Panel mounting ................................................................ 7
1.7.2 Wall mounting/desktop stand ........................................... 8
1.8 Exploded diagram........................................................... 9
1.9 Dimensions and cutout ................................................ 10
Chapter2 System Quick Starting.......................... 11
Chapter3 TheEngine ofthe GOT-1120T ............... 17
3.1 Introduction................................................................... 18
3.2 Main board..................................................................... 18
3.2.1 Connector pin assingments ............................................ 19
3.3 GOT-1120T I/O board....................................................... 20
Chapter4 SystemTuning ....................................... 23
4.1 LCD contrast tuning ..................................................... 24
4.1.1 LCD brightness tuning .................................................... 24
4.2 Touchscreen calibration .............................................. 25
Chapter5 Maintenance .......................................... 27
5.1 CPU board replacement............................................... 28
5.2 Fuse replacement ......................................................... 30
AppendixA Serial Port Settings ............................ 31
A.1 Baud Rate Settings (SW1) ........................................... 32
A.2 Data Format/RS-422 Control Settings ........................ 33
AppendixB WatchdogTimer Programming
Example............................................... 35
B.1 Watchdog timer programming example ..................... 36
AppendixC Windows2000/XPTouchScreen
Installation .......................................... 37
C.1 Touchscreen driver in Windows 2000 ......................... 38
AppendixD FuseSpecifications ............................ 47
Table of Figures
Figure 1.6-1 I/O ports arrangement ............................................................. 7
Figure 1.7-1 Panel mounting ........................................................................ 7
Figure 1.8-1 Exploded diagram .................................................................... 9
Figure 1.9-1 Dimensions and cutout ......................................................... 10
Figure 2-1 Install HDD .............................................................................. 12
Figure 2-2 Install CompactFlash memory card ..................................... 13
Figure 2-3 Power connector and power lines ....................................... 13
Figure 2-4 Power connector pin assignment ........................................ 14
Figure 2-5 Plug the power lines to the system power receptor. .......... 14
Figure 2-6 Turn on power switch ............................................................ 15
Figure 3.2-1 GOT-1120T main board .......................................................... 18
Table 3.2-1 GOT-1120T main board connector/jumper list ..................... 18
Figure 3.3-1 GOT-1120T I/O board (I/O port side) ...................................... 20
Figure 3.3-2 GOT-1120T I/O board (LCD side) ........................................... 21
Figure 4.1-2 Remove the CPU Board cover ............................................... 24
Figure 4.1-1 Adjust LCD contrast ............................................................... 24
Figure 4.1-3 Adjusting the LCD brightness ............................................... 25
Figure 5.1-1 CPU board cover .................................................................... 28
Figure 5.1-2 Remove the CPU board cover ............................................... 28
Figure 5.1-3 Remove the CPU board ......................................................... 29
Figure 5.2-1 Replace the fuse .................................................................... 30
Figure C-1 Hardware ................................................................................ 38
Figure C-2 Device manager ..................................................................... 39
Figure C-3 Uninstall the driver ................................................................. 40
Figure C-4 Mouse properties .................................................................. 41
Figure C-5 Update driver .......................................................................... 42
Figure C-6 Select driver from known list ................................................ 43
Figure C-7 Find out TouchScreen in the manufacturers list ................. 44
Figure C-8 Re-install the driver ............................................................... 45
Figure C-9 Finish installation of touchscreen driver .............................. 46
Table of Tables
Table 1.3-1 LCD specifications ................................................................... 5
Table 1.4-1 Touchscreen specifications ................................................... 6
Table 3.2-1 GOT-1120T main board connector/jumper list ..................... 18
Table 3.2-2 J1 RTC control jumper ........................................................... 19
Table 3.3-1 GOT-1120T I/O board connector/jumper list ........................ 22
Table des matières
Autres manuels AXIOMTEK écran tactile
Manuels écran tactile populaires d'autres marques
Elecro Engineering
Elecro Engineering Poolsmart Plus Instructions d'installation
Johnson Controls
Johnson Controls IQ4 HUB Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET2270L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems ET1002L Manuel utilisateur
Elo TouchSystems
Elo TouchSystems 3201L Manuel utilisateur
Duratec
Duratec S15 Manuel utilisateur
