Avenview FO-DVI-DL-330X Manuel utilisateur

www.avenview.com

DVI Dual Link Extender over 2 Strand

Multi-Mode Fiber Optic Cable

Model #: FO-DVI-DL-330X

The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with

respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any

time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in

Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products

including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.

Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.

Ver. 1.3

www.avenview.com

Table of Contents

Section 1: Getting Started ...................................................................................................................... 3

1.1 Important Safeguards ............................................................................................................ 3

1.2 Safety Instructions ................................................................................................................. 3

1.3 Regulatory Notices Federal Communications Commission (FCC) ......................................... 4

1.4 Introduction ........................................................................................................................... 4

1.5 Package Contents................................................................................................................... 5

1.6 Before Installation.................................................................................................................. 5

1.7 Panel Description................................................................................................................... 6

1.8 Installation ............................................................................................................................. 7

1.9 Function Switch...................................................................................................................... 7

1.10 General Troubleshooting ....................................................................................................... 8

Section 2: Specifications....................................................................................................................... 10

2.1 Signal Pin Assignment (Single Link) ............................................................................................ 11

2.2 Signal Pin Assignment (Dual Link) .............................................................................................. 12

www.avenview.com

Section 1: Getting Started

1.1 Important Safeguards

Please read all of these instructions carefully before you use the device. Save this manual for future

reference.

What the warranty does not cover

Any product, on which the serial number has been defaced, modified or removed.

Damage, deterioration or malfunction resulting from:

Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized

product modification, or failure to follow instructions supplied with the product.

Repair or attempted repair by anyone not authorized by us.

Any damage of the product due to shipment.

Removal or installation of the product.

Causes external to the product, such as electric power fluctuation or failure.

Use of supplies or parts not meeting our specifications.

Normal wear and tear.

Any other causes which does not relate to a product defect.

Removal, installation, and set-up service charges.

1.2 Safety Instructions

The Avenview FO-DVI-DL-330X, DVI Dual Link Extender over Fiber Optic, has been tested for conformance to

safety regulations and requirements, and has been certified for international use. However, like all electronic

equipment’s, the FO-DVI-DL-330X should be used with care. Read the following safety instructions to protect

yourself from possible injury and to minimize the risk of damage to the unit.

Do not dismantle the housing or modify the module.

Dismantling the housing or modifying the module may result in electrical shock or burn.

Refer all servicing to qualified service personnel.

Do not attempt to service this product yourself as opening or removing housing may expose you to

dangerous voltage or other hazards

Keep the module away from liquids.

Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid

falls or spills on to the housing, unplug the module immediately.

Have the module checked by a qualified service engineer before using it again.

Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before

cleaning.

www.avenview.com

1.3 Regulatory Notices Federal Communications Commission (FCC)

This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation.

Any changes or modifications made to this equipment may void the user’s authority to operate this

equipment.

1.4 Introduction

Avenview FO-DVI-DL-330X Series with fiber optic cable system lets you extend dual link digital signal up to

100m (330 feet).

-High Speed and long distance transmission

-Uses 2 strand multi-mode LC fiber optic cable

-Supports both Single link and Dual link by selectable function switch

-Supports up to Dual Link WQXGA (2560 x 1600) resolution and WUXGA (1920x1200) Single link

-Self-detecting function for EDID

-Supports two mode for DDC

oReal Mode: Uses one CAT5 cable for DDC

oEmulation: Pseudo DDC detection function for EDID information (2560x1600)

www.avenview.com

1.5 Package Contents

Before you start the installation of the converter, please check the package contents.

-FO-DVI-DL-330X Transmitter x 1

-FO-DVI-DL-330X Receiver x 1

-Power Adapter (+5VDC 2A) x 1

-User’s Manual x 1

1.6 Before Installation

Put the product in an even and stable location. If the product falls down or drops, it may cause an

injury or malfunction.

Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high

humidity.

Use the DC power adapter with correct specifications. If inappropriate power supply is used then it

may cause a fire.

Do not twist or pull by force ends of the optical cable. It can cause malfunction.

Fiber Optic Cable is not included in the package

www.avenview.com

1.7 Panel Description

REAR PANEL (Receiver, FO-DVI-DL-330X)

UTP port for

DDC

DVI Input

port

Power jack

Optical 2ch L

C port

UTP port for

DDC

DVI Output po

Power jack

Optical 2ch L

C port

www.avenview.com

1.8 Installation

Avenview FO-DVI-DL-330X is composed of a transmitter and a receiver. The Transmitter should be connected

to the computer’s DVI Port and the Receiver should be connected the DVI Port of the digital display device.

Avenview FO-DVI-DL-330X Transmitter is designed to be used with the LC type standard optical cable.

Transmitter and Receiver have each of 7 Optical port which are marked on the optical port of the fiber cable

connection.

To setup Avenview FO-DVI-DL-330X follow these steps for connecting to a device:

1. Connect FO-DVI-DL-330X Transmitter unit to DVI source

2. Connect FO-DVI-DL-330X Receiver unit to DVI port of display.

3. Connect 2 Strand Fiber Optic LC Type cable to both Transmitter and Receiver.

4. Plug the power to Receiver Unit.

5. Power on DVI Source and DVI Display.

1.9 Function Switch

EDID: Switch in front of Transmitter

-REAL: EDID data of connected monitor is transmitted between Transmitter and Receiver in real time

through UTP cable.

-Emulation: Certain EDID data pre-set in the Transmitter is used in signal transmission. UTP cable is

not necessary.

MODE: Switch in front of Transmitter

-Single: When you use Single link display (up to 1920 x 1200), select ‘Single’ switch.

-Dual: When you use Dual link display (2560 x 1600), select ‘Dual’ switch.

Use the DC adapter (included in the package) for the Receiver. The Transmitter which is connected

to a computer uses power from the computer.

If Transmitter power LED doesn’t light up after PC is turned on, then use the external power adapter

for Transmitter.

www.avenview.com

1.10 General Troubleshooting

www.avenview.com

Problem

Possible Solution

Power ON

Power LED does not

work

Please check out voltage of adapter. (DC +5V)

Ensure that power adapter correctly plugged

Cannot read selected

EDID

Select switch the emulation mode

-Retry self EDID read

-Check the monitor to read EDID

Select switch the real mode.

-Please check and connected the UTP cable. (Only the direct

type)

-Please check if the DVI cable is connected.

Resolution Issue

Select single mode switch

-Max resolution 1920x1200@60Hz

-Some monitor will not support this mode.

Select dual mode switch

-Max resolution 2560x1600@60Hz

-Please check and connect DVI cable type (Should use DVI-Dual

cable)

Noise or no display

-Please check the DVI and optical fiber cable is connected.

*** The max resolution is different on to connected monitor

Self EDID Setting :

1) DDC function switch set to Emulation.

2) DVI cable connection between TX and display.

3) Supply power to TX (DC +5[V]).

4) LED blink -> LED ON

www.avenview.com

Section 2: Specifications

Item

Description

Units

FO-DVI-DL-330X (Transmitter)

FO-DVI-DL-330X (Receiver

Unit Description

DVI Dual Link Transmitter

DVI Dual Link Receiver

Input Signal

TMDS Signal (DVI 1.0 Standard)

Output Signal

TMDS Signal (DVI 1.0 Standard)

Video Bandwidth

1.65Gbps (Single Link)

Supported Resolution &

Distance

Single Link: WUXGA 1920 x 1200 @ 100 meters ( 330 feet)

Dual Link: WQXGA 2560 x 1600 @ 100 meters (330 feet)

Optical Converter

2 ch 850 nm Multi-Mode VCSEL

2 ch GaAs PIN photo Diode

DVI Connector

24 pin DVI-D Plug

Optical Connector

2 LC Connector

DDC Link Connector

Rj45

Fiber Type

62.5/125 µm Multi-mode glass fiber

Dimensions (L x W x H)

3.4” x 5.3” x 1”

Power Supply

5V 2A DC

Power Consumption

1.5W (max)

Environmental

Operating Temperature

32˚~ 104˚F (0˚to 40˚C)

Storage Temperature

-4˚~ 140˚F (-20˚~ 60˚C)

Relative Humidity

20~90% RH (no condensation)

Table des matières

Autres manuels Avenview Extenseur

Avenview

Avenview FO-DVI-1080X-SET Manuel utilisateur

Avenview

Avenview HDMI-C5SP-4 Manuel utilisateur

Avenview

Avenview FO-DP4K-300-EMIX Manuel utilisateur

Avenview

Avenview VGA-C5RS-SET Manuel utilisateur

Avenview

Avenview FO-DVI-1000X-EMIX Manuel utilisateur

Avenview

Avenview HDM-C5SP-8 Manuel utilisateur

Avenview

Avenview HDMI-C5-4 Manuel utilisateur

Avenview

Avenview FO-DP-300-EMI Manuel utilisateur

Avenview

Avenview HDM-C5-3X-SET Manuel utilisateur

Avenview

Avenview VGA-C5ARS-SET Manuel utilisateur

Avenview

Avenview HBT2-C6BPOC-SET Manuel utilisateur

Avenview

Avenview HDM-SHAREPRO-IP Manuel utilisateur

Avenview

Avenview Cat5 Manuel utilisateur

Avenview

Avenview FO8K-DP MM Series Manuel utilisateur

Avenview

Avenview FO-DVI-1080LC-Set Manuel utilisateur

Avenview

Avenview HDM3D-C53X-SET Manuel utilisateur

Avenview

Avenview KVM-C5 Series Manuel utilisateur

Avenview

Avenview VGA-C5A-R Manuel utilisateur

Avenview

Avenview VGA-C5A-SET Manuel utilisateur

Avenview

Avenview HBT-C6PLT-SET Manuel utilisateur

Avenview

Avenview FO-DVI-XX-MM Manuel utilisateur

Avenview

Avenview HBT-C6POE-SET Manuel utilisateur

Avenview

Avenview HDM3D-C5IR-SET Manuel utilisateur

Avenview

Avenview HDSD FO-HDSDI-L-SET Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur