Automatic Technology SecuraLift GDO-7V1 Guide de démarrage rapide
GDO-7V1 SecuraLift®
Overhead Garage Door Opener
INSTALLATION INSTRUCTIONS | OWNERS COPY
2GDO-7V1 SecuraLift® Owner Installation Instructions
WARNING: It is vital for the safety of persons to follow all
instructions. Failure to comply with the installation instructions
and the safety warnings may result in serious personal injury
and/or property and remote control opener damage. Please
save these instructions for future reference.
Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of
an Automatic Technology Australia Pty Ltd Garage Door Opener. Automatic Technology Australia Pty Ltd hereby further
expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as a
result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener
in accordance with these installation instructions.
Owner Installation Instructions GDO-7V1 SecuraLift® 3
Safety Precautions 4
Opener Features 6
Operating Controls 6
Kit Contents 10
Installation 11
Tube Pipe Assembly 11
Determine Door Type 12
Mounting - Track Type Door 12
Using inbuilt antivibration brackets 14
Mounting - Spring Loaded Door 15
Mounting Door Bracket & Arms 16
Easy Access Transmitter 16
Programming the Opener 17
Setting Travel Limits - Control Pane 17
Setting Travel Limits - Transmitter 18
Safety Obstruction Force Test 19
Coding Transmitters 20
Door 20
Courtesy Light 20
Vacation Mode 20
Pet Mode 20
Storing Transmitter From Remote Location 21
Erasing Transmitter Codes 21
Accessories 22
Photo Electric Beam 22
Auto-Close 22
Final Set Up 23
Courtesy Light Time 23
Pet Mode Door Height 23
Transmitter Wall Bracket 23
Re-Initializing 23
Parameters 24
Door Status Indicators 24
System Specification 26
Factory Default Settings 26
Trouble Shooting Guide 28
Maintenance Record 29
Parts List 30
Warranty 32
GDO-8V1 SecuraLift®
Overhead Garage Door Opener
4GDO-7V1 SecuraLift® Owner Installation Instructions
CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be installed.
This accessory allows manual operation of the garage door from outside in case of power failure.
For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a Photo Electric
Beam. In most countries Photo Electric Beams are mandatory on all garage doors fitted with
automatic openers. For a small additional outlay ATA recommends that Photo Electric Beams be
installed with the automatic opener ensuring additional safety and peace of mind.
DO NOT operate the garage door opener unless the garage door is in full view and free
from objects such as cars and children/people. Make sure that the door has finished moving
before entering or leaving the garage.
DO NOT operate the garage door opener when children/persons are near the door.
Children must be supervised near the garage door at all times when the door opener
is in use. serious personal injury and/or property damage can result from failure to
follow this warning.
DO NOT allow children to operate the garage door opener. serious personal
injury and/or property damage can result from failure to follow this warning.
Regularly check to make sure that the safety obstruction force is working
correctly, and is tested (by placing a 50mm high object on the floor)
and set as per the Installation Instructions Manual. Failure to follow the
manual could result in serious personal injury and/or property damage.
This test must be repeated at regular intervals and the necessary
adjustments made as required.
DO NOT disengage the door opener to manual operation with
children/persons or any other objects including motor vehicles
within the doorway.
The door opener is not intended for use by young children
or infirm persons without adequate supervision. Children
should be supervised to ensure that they do not play
with the remote transmitters or the opener.
Keep hands and loose clothing clear of the door
and door opener at all times.
The unit should be installed so that it is protected
from the elements. It should not be exposed
WARNING: It is vital for the safety of persons to follow
all instructions. Failure to comply with the following
Safety Rules may result in serious personal injury and/or
property damage.
Important safety instructions
Owner Installation Instructions GDO-7V1 SecuraLift® 5
to water or rain. It is not to be immersed in water or sprayed directly by a hose or other water carrying device.
The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage
door installer prior to installation of the opener.
Frequently examine the installation, in particular cables, springs and mountings for signs of wear,
damage or imbalance. DO NOT use if repair or adjustment is needed since a fault in the installation
or an incorrectly balanced door may cause injury. DO NOT attempt to repair the door yourself as
hardware is under extreme tension.
Remove or disengage all garage door locks and mechanisms prior to installation of the opener.
Connect the garage door opener to a properly earthed general purpose 240V mains power
outlet installed by a qualified electrical contractor.
Disconnect the power cord from mains power before making any repairs or removing
covers. Only experienced service personnel should remove covers from the garage
door opener.
When using auto close mode, a photo electric beam must be fitted correctly
and tested for operation at regular intervals. extreme caution is recommended
when using auto close mode. all safety rules must be followed.
In order for the garage door opener to sense an object obstructing the
door way, some force must be exerted on the object. As a result the
object, door and/or person may suffer damage or injury.
If the power supply cord is damaged, it must be replaced by an ATA
service agent or suitably qualified person.
Make sure that the door is fully open before driving in or out of
the garage and fully closed before leaving the driveway.
Make sure that remote controls are kept out of reach of
children.
Install the wall switch or wall mounted
transmitter in a location where it is out of
reach of children and the garage door is
visible.
Important safety instructions
6GDO-7V1 SecuraLift® Owner Installation Instructions
Operation
To open or close the door simply press the hand held transmitter, the wall mounted
transmitter, or optional wall switch for two seconds. During an open or close cycle
the door can be stopped by pressing the button while the door is in motion. The
next actuation will move the door in the opposite direction.
Hopping code
Every time a transmission is made from the remote transmitter a new security
code is generated. The number of possible code combinations is over 4.29
billion. This greatly enhances the security of the system. Code “grabbing” is made
a thing of the past.
S-alps (semi automatic limits positioning system)
The ALPS system does away with manual adjustment of the doors’ limits position using
mechanical parts, such as cams and micro switches. During installation the hand held
transmitter can be programmed to set the door limits positions.
Anti travel electronic brakes
opener has anti travel electronic brake mechanism which ensure the opener stops the door at
exact location
ISS (intelligent safety obstruction system)
While the door is performing a close cycle, should it hit an obstacle or be restricted in some manner, it will
automatically reverse. The amount of force the door should encounter before reversing is automatically
adjusted by the doors control system during the initial installation of the automatic door opener. The door
will also stop if restricted whilst opening. The Safety Obstruction Force should be checked at least once a
month. See installation manual for instructions.
Security code store
The SecuraLift® Garage Door Opener uses state of the art technology in storing your selected transmitter
security code. Up to 24 different transmitters can be stored in the openers memory.
Features
Thank you for purchasing the ATA SecuraLift® Automatic
Garage Door Opener. This opener is designed to suit
sectional overhead and one piece tilt up doors. The
components and materials used in this opener are of
the latest technology and highest quality. Listed
below are some of the many features.
Owner Installation Instructions GDO-7V1 SecuraLift® 7
Over load indicator
When the maximum opening and closing capacity of the opener is exceeded the red and
green Limits LEDs flash alternately to indicate that an overload has occurred.
Auto courtesy light
The courtesy light on the opener comes on automatically whenever the door is
activated. The light can also be switched on and off without operating the door.
This is done by pressing the button on any hand held or wall mounted transmitter
which has been stored with the light code.The light will stay on for approximately
three minutes then switch off. This time is also adjustable.
Anti vibration brackets
opener has inbuilt antivibration brackets hang the opener by using anti vibration
brackets where noise is the problem.
Vacation mode
A hand held transmitter can be programmed to lock and unlock all other
transmitters that have been programmed into the openers’ memory. The vacation
mode can be used when the door is left idle for long periods of time.
Pet (pedestrian) mode
The hand held transmitter can be programmed to open the door partially so that the
family pet can enter and exit the garage at any time. You may also wish to open the
door to a height suitable only for pedestrian access. The door opening position is also
programmable.
Auto close mode
The opener can be programmed to automatically close after an open cycle. The auto close time
is adjustable. It is compulsory to install a Photo Electric Beam if this mode is selected, otherwise the
door may cause personal injury or damage to property.
Photo electric beam (optional)
The opener has an input for a photo electric beam to be connected for extra safety protection and use of the
auto close mode.
Manual operation
The opener is equipped with a unique manual disengaging device. If the power to the opener is disrupted for
any reason the door can be put into manual mode by pulling down on the string handle on an angle towards
the door. This will allow you to manually open or close the door. To re-engage the opener pull the string
handle away from the door.
Features
8GDO-7V1 SecuraLift® Owner Installation Instructions
Operating controls
P. E. Shunt. The shunt has to be removed when connecting a Photo Electric Beam.
NOTE: P.E. Shunt must not be removed otherwise the opener will not function correctly. Remove only
when a P.E beam is to be connected. PROG INPUT is used for the connection of the ATA Handheld
Programmer for the purpose of editing control and receiver functions.
Terminal Block. 24V PWR is used to power devices such as photo electric beams.
PE (Input) for photo electric beam for safety and auto-close function.
LGT (Input) allow hard wired external trigger for the opener’s courtesy light.
O/S/C INPUT is used for the connection of a wired switch (momentary contact). This switch can then be
used to open, stop or close the door. Install the wall switch in a location where the switch is out of reach
of children and the garage door is visible.
Set button (yellow) is used during the installation phase together with the Open and Close buttons to set
the door limit positions. The Set button is also used to re-initialize the Opener.
Operate button (Yellow) is used during installation to test the open, stop and close cycles for the opener.
The opener has to be initialized by the Reset button before the O/S/C button becomes operable.
Plus (+) button (green) is used during installation to help set the open limit position. Pressing and
holding this button will move the door in the open direction. Movement stops when the button is
released.
NOTE: The open safety obstruction detection is inoperable whenever the Open or Close Drive button is
used to move door.
Open limit led (green) the led is very helpful during installation. It illuminates and flashes when the door
is opening and remains steady on when the open limit position has been reached.
Force margin set Button The obstruction force pressure is set automatically by the opener during
installation. The pressure can be adjusted manually using the Force Margin Set button (White). Holding
the Force Margin Set button and pressing the Plus (+) or Minus (-) button will increase or decrease the
amount of force. The Force Margin Set is only ever used if other environmental factors (wind, etc.) effect
the operations of the door/opener.
Light code button (white) is used for storing or erasing the transmitter button (code) you wish to use to
switch the courtesy light on the opener on or off.
Coding led (red) light flashes when a code is being stored or when a transmitter button is pressed.
Door code button (blue) is used for storing or erasing the transmitter button you wish to use to
command the door to open, stop or close.
Door status LED (Yellow)
Minus (-) button (red) is used during installation to help set the close limit position. Pressing and holding
this button will move the door in the close direction. Movement stops when the button is released.
NOTE: The close safety obstruction detection is inoperable whenever the Open or Close Drive button is
used to move door.
Close limit LED (red) the led is very helpful during installation. It illuminates and flashes when the door is
closing and remains steady on when the close limit position has been reached.
01
02
03
04
05
06
07
08
09
10
11
12
13
Owner Installation Instructions GDO-7V1 SecuraLift® 9
01 02
03 04 05 06 07
08
09
10
11
Operating controls
Datum adjust screw is used during limits set up to indicate the mid point of the door’s travel.
Auto close time button (White) is used to adjust the auto close time. While holding in the auto close
button and then pressing the open button the time is increased. Each press will increase the time by 5
seconds. Pressing the close button will decrease the time.
Engage/disengagement cord when pulled down and released this will select manual mode on the
opener, particularly when there is a power failure. Pulling down and again releasing will select automatic
mode on the opener. The length of the string is adjustable.
Easy access transmitter The “manual release” engage/disengagement handle has within its housing a
14
15
16
17
12 13
14
15
16
10 GDO-7V1 SecuraLift® Owner Installation Instructions
Package contents
GDO-7 Securalift® drive unit 1
Securacode® key ring transmitter pack 1
Pack includes two keyring transmitters two batteries
and one wall mount bracket for ptx4 transmitter
Easy access transmitter - EAT-1 (not available some models) 1
Tubes 5
Tube inserts 4
Pipe support assembly 1
Chain 1
Shuttle assembly 1
Door attachment arms 2
Accessory pack 1
Installation manual 1
Table des matières
Autres manuels Automatic Technology ouvre-porte de garage
Automatic Technology
Automatic Technology GDO-11v1 SecuraLift Manuel utilisateur
Automatic Technology
Automatic Technology Hiro GDO-12V1 Manuel utilisateur
Automatic Technology
Automatic Technology GDO-10v1Toro Manuel utilisateur
Automatic Technology
Automatic Technology GDO-10v1 Toro Manuel utilisateur
Automatic Technology
Automatic Technology GDO-9V1 SecuraLift Manuel utilisateur
Automatic Technology
Automatic Technology GDO-6 EasyRoller Manuel utilisateur
Automatic Technology
Automatic Technology GDO-8 Shed Master Manuel utilisateur
Automatic Technology
Automatic Technology Toro GDO-10v2 Manuel utilisateur
Automatic Technology
Automatic Technology Dominator AM800 Manuel utilisateur
Automatic Technology
Automatic Technology PA1000V1 Manuel utilisateur
Automatic Technology
Automatic Technology HiRO GDO-12 Manuel utilisateur
Automatic Technology
Automatic Technology GDO-6v3 EasyRoller Manuel utilisateur
Automatic Technology
Automatic Technology GDO-6 v2 Manuel utilisateur
Automatic Technology
Automatic Technology iOpener RD40 Manuel utilisateur
Automatic Technology
Automatic Technology Smart Phone Control Manuel utilisateur
Automatic Technology
Automatic Technology GDO-8V2 EasyRoller II Manuel utilisateur
Automatic Technology
Automatic Technology Toro GDO-10V2L2 Manuel utilisateur
Automatic Technology
Automatic Technology GDO-9 Dynamo Gen 2 Manuel utilisateur
Automatic Technology
Automatic Technology NeoSlider TrioCode 128 NES-500 Manuel utilisateur
Automatic Technology
Automatic Technology GDO-8v1 EasyRoller II Manuel utilisateur
Automatic Technology
Automatic Technology GDO-6v3 EasyRoller Manuel utilisateur
Automatic Technology
Automatic Technology GDO-9 ENDURO GEN2 Guide de planification
Automatic Technology
Automatic Technology 62717 Manuel utilisateur
Automatic Technology
Automatic Technology Axess Pro Series Manuel utilisateur
