AudioCodes MediaPack 124 Manuel utilisateur

1 |Page

MediaPack™ 124 Analog VoIP Gateway

Quick Setup Guide

Welcome

Congratulations on purchasing your AudioCodes MediaPack 124 (MP-124 Rev. E) Analog Voice-over-IP (VoIP)

Media Gateway (hereafter, referred to as device)!

This document is only intended to provide basic setup instructions for initial access to the device and

connecting it to your network. For advanced configuration and cabling, refer to the User's Manual and

Hardware Installation Manual respectively, which can be downloaded from AudioCodes website at

https://www.audiocodes.com/library/technical-documents.

Before you begin, please read the Safety Precautions on page 7.

Package Contents

Make sure that the following items (in addition to any separate-orderable items that you may have purchased)

are included with your shipped device:

2 x short equal-length brackets and bracket-to-device screws for 19-inch rack installation

(AC-powered model) 1 x AC power cord

(DC-powered model) 1 x unwired DC terminal block with 2 x crimping screws

Regulatory Information document

This document

2 |Page

Physical Description

Protective earthing screw (mandatory for all installations). Accepts a 6-32 UNC screw.

(AC)

100-240V

50 – 60Hz 1.0A

(DC)

48V = 1.3A

AC power plug entry or DC inlet for terminal block (depending on ordered model).

Ready LED (located on front panel):

Green On

Power received by device and normal operation

Amber Blinking

Loading software or initialization

Red On

Malfunction

Off

No power

ANALOG FXS

LINES 1-24

50-pin Telco connector providing up to 24 Foreign eXchange Subscriber (FXS) lines.

Channels 1-24 LED (located on front panel):

Green On

Phone in off-hook position or ringing

Red On



Line malfunction.

SRTP is enabled and device resources (DSPs) are currently

unavailable for calls on these ports (their resources are

"borrowed" for SRTP functionality). This LED state applies to

channel LEDs 19 to 24.

Off

Phone in on-hook position or not connected

Control LED (located on front panel):

Green Blinking

Sending and receiving signaling (SIP) messages

Off

No SIP traffic

Data LED (located on front panel):

Green Blinking

Sending RTP packets

Red Blinking

Receiving RTP packets

Off

No RTP traffic

RS-232

RS-232 serial interface port (RJ-45).

ETHERNET

10/100Base-T Ethernet port (RJ-45) for connecting to the IP network.

LAN LED (located on front panel):

Green On

Ethernet link established

Red On

Malfunction

Off

No Ethernet link

MP-124 with DC Power

MP-124 with AC Power

3 |Page

The Reset pinhole button, located on the front panel, resets the device or restores it to factory defaults. To

restore the device to factory defaults: Disconnect the Ethernet cable and then with a paper clip or any other

similar pointed object, press and hold down the button for at least 12 seconds, but no more than 25 seconds.

Mounting the Device

You can mount the device in a standard 19-inch rack, using the two mounting brackets (supplied) which you

first need to attach to the sides of the chassis.

4 |Page

Cabling the Device for Power

Depending on ordered model, your device can be powered either from a standard alternating current (AC)

electrical wall outlet or a -48V DC power source.

Warning:

•The device must always be grounded.

•If the FXS wires exit the building, they must be surge protected using gas discharge arrestors. For more

information, refer to the device's Hardware Installation Manual.

1. GROUNDING: Connect a grounding lug that is attached to your grounding wire to the device, using the

terminal screw located on the rear panel. Attach the grounding wire to the equipotential grounding

busbar. For more information, refer to the device's Hardware Installation Manual.

2. AC POWER: Insert the female connector that is located on one end of the AC power cord (supplied) into

the device's AC power socket, located on the rear panel. Insert the male plug that is located on the

other end of the AC power cord into a standard electrical wall outlet.

3. DC POWER: Connection to mains power of -48V must be made by trained or instructed service

personal. For connection to the device, use the supplied DC terminal block (supplied) in conjunction

with 18-AWG wires, paying attention to correct polarity (as indicated by the +and –labels on the

chassis, above the DC inlet). Secure the wires by fastening the screws located above them in the

terminal block. Insert the DC terminal block plug into the DC inlet, located on

the rear panel. Connect the DC power leads to a 48V DC power source. Use a

DC rated 5A circuit breaker in series with the -48V wire as a disconnect

device.

When power is received by the device, the Ready LED that is located on the front panel is lit green.

5 |Page

Assigning an IP Address to the Device

Use the device's factory default IP address (10.1.10.10/16 and Default Gateway 0.0.0.0) to initially access the

device's Web-based management interface and then change the IP address to suit your network's addressing

scheme for subsequent connectivity.

1. Using a crossover RJ-45 Ethernet cable, connect the device's Ethernet port that is located on the rear

panel and labeled ETHERNET, to the LAN port of your computer.

2. Change the IP address of your computer to correspond with the device's default IP address and subnet

mask.

3. On your computer, open a standard Web browser (for example, Google Chrome), and then in the URL

field, enter the device's default IP address; the Web Login screen appears:

4. Type in the default username (Admin) and password (Admin), and then click Login.

6 |Page

5. Open the IP Settings table (Configuration tab > VoIP menu > Network > IP Interfaces Table).

6. Modify the IP address to suit your network addressing scheme:

In the 'IP Address' field, enter the new IPv4 IP address in dotted-decimal notation.

In the 'Subnet Mask' field, enter the new subnet mask in dotted-decimal notation.

In the 'Default Gateway Address' field, enter the new IP address of the Default Gateway in dotted-

decimal notation.

7. Click Submit to apply your settings.

8. Open the Maintenance Actions page (Maintenance tab > Maintenance menu > Maintenance Actions),

and then click BURN to save your settings to the device's flash memory. This process also causes the

device to reset.

As you have changed the device's IP address, your connection to the device's management interface

through your browser is no longer available.

9. Disconnect the device's Ethernet cable from your computer and then connect it to your network.

10. Access the device's management interface using the device's new IP address.

7 |Page

Safety Precautions

This device is an indoor unit and therefore, must not be installed outdoors.

Ethernet cabling must be routed only indoors and must not exit the building.

The device must be installed and serviced only by qualified service personnel.

Do not open or dismantle the device.

Do not expose the device to water or moisture.

Make sure the device is installed in a well-ventilated location to avoid over heating of internal

components and subsequent damage.

Do not place any object on top of the device and make sure that sufficient clearance from the top and

sides are maintained to ensure proper airflow to avoid over heating of internal components.

Operate the device in an ambient temperature (Tma) that does not exceed 40°C (104°F).

The device must be installed only in restricted access locations.

The device must be connected permanently to earth via the screw terminal, located on the device's

rear panel, as per the instructions in the device's Hardware Installation Manual.

The grounding connection must not be removed unless all FXS lines are first disconnected from the

device.

Installation of the device must be in accordance with national electrical codes and conform to local

regulations.

AC Power: Use only the supplied AC power cord for connection to the power source.

AC Power: Connect the device to an electrical socket outlet that provides protective earthing

(grounding).

DC Power: Connect the device to a safety extra-low voltage (SELV) source that is sufficiently isolated

from the mains.

The device is immune against power surge levels of up to 1 Kilovolts (KV) as required by the following

standards: IEC 61000-4-5, EN 55024, and EN 300386. Power surges above protection levels as required

by EN 55024 and EN 300386 may cause damage to the device.

The device includes an integrated secondary surge protection, but does not include primary telecom

protection. To comply with ITU-K.21 requirements when the telephone lines are routed outside the

building, it is essential to install additional protection using a three-electrode Gas Discharge Tube (GDT)

rated 350V as a primary protection on the MDF, located at the entrance point of telephone wiring to

the building. The center pin of the GDT must be connected to ground.

For FXS ports, use minimum 26-AWG wiring if it exits the building.

8 |Page

About AudioCodes

AudioCodes Ltd. (NasdaqGS: AUDC) is a leading vendor of advanced voice networking and media processing

solutions for the digital workplace. With a commitment to the human voice deeply embedded in its DNA,

AudioCodes enables enterprises and service providers to build and operate all-IP voice networks for unified

communications, contact centers and hosted business services. AudioCodes’ wide range of innovative products,

solutions and services are used by large multinational enterprises and leading tier one operators worldwide.

International Headquarters

1 Hayarden Street,

Airport City

Lod 7019900, Israel

Tel: +972-3-976-4000

Fax: +972-3-976-4040

AudioCodes Inc.

200 Cottontail Lane,

Suite A101E,

Somerset, NJ 08873

Tel: +1-732-469-0880

Fax: +1-732-469-2298

Website: https://www.audiocodes.com/

What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your Gateway To VoIP,

3GX, VocaNom, AudioCodes One Voice and CloudBond are trademarks or registered trademarks of AudioCodes Limited. All

other products or trademarks are property of their respective owners. Product specifications are subject to change without

notice.

Date Published: 16 September 2019

Document #: LTRT-53222

Autres manuels pour MediaPack 124

Table des matières

Autres manuels AudioCodes Porte

AudioCodes

AudioCodes Mediant 1000 Manuel utilisateur

AudioCodes

AudioCodes Mediant 800B Manuel utilisateur

AudioCodes

AudioCodes Mediant 3000 Manuel utilisateur

AudioCodes

AudioCodes Media Pack MP-124 Manuel utilisateur

AudioCodes

AudioCodes Media Pack MP-11x Instructions de montage

AudioCodes

AudioCodes Mediant 3100 Instructions de montage

AudioCodes

AudioCodes Mediant 800C SBC Guide de référence rapide

AudioCodes

AudioCodes Mediant 1000 Manuel utilisateur

AudioCodes

AudioCodes Mediant 3000 Instructions de montage

AudioCodes

AudioCodes MediaPack MP-264 Manuel utilisateur

AudioCodes

AudioCodes Mediant 1000 Manuel utilisateur

AudioCodes

AudioCodes MediaPack MP-262 Manuel utilisateur

AudioCodes

AudioCodes Mediant 1000 Manuel utilisateur

AudioCodes

AudioCodes MediaPack MP-124 Manuel utilisateur

AudioCodes

AudioCodes MediaPack 124 Instructions de montage

AudioCodes

AudioCodes Mediant 1000B Instructions de montage

AudioCodes

AudioCodes Mediant 1000 Manuel utilisateur

AudioCodes

AudioCodes MP-108 Manuel utilisateur

AudioCodes

AudioCodes i Series Instructions de montage

AudioCodes

AudioCodes MP-26 series Manuel utilisateur

AudioCodes

AudioCodes MediaPack MP-124 Manuel utilisateur

AudioCodes

AudioCodes Mediant 1000 Instructions de montage

AudioCodes

AudioCodes MediaPack MP-118 Manuel utilisateur

AudioCodes

AudioCodes Mediant 800 Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur