Atdec Levitate L-PB Manuel utilisateur









The default base setup allows  of

rotation of the Lower Arm around the base.

If you want to limit the Lower Arm rotation to

go to A1, if not skip to A2.



To limit the Lower Arm rotation to insert

the Brake Pin underneath the Desk Clamp.

Position Arm Assembly on the work

surface so that the Desk Clamp hangs over

the edge.

Using the 5mm Allen Key, close

the Desk Clamp to grip the work

surface. Tighten very firmly.

The Clamp Pad will automatically

rotate under the work surface

when tightened.

Remove and re-install the Desk Clamp, using

the 5mm Allen Key supplied. Then go to A2.



 When sliding the Desk Clamp

between two work surfaces, ensure

that the Clamp Pad is fully open

and parallel with the edge of the

work surface.

 The unique top loading Desk Clamp allows product installation/removal

without having to gain access to the underside of the work surface.

 Desk Clamp is now installed, please skip to Step 3 (PTO>>>).

Brake

Pin (x1)

5mm & 2mm

Allen Key

(x1each)

Spacer

Bush (x4)

M8 x 45mm/60mm

Bolts (x1 each)

Security

Screw (x1)

Bolt Through

Washers (x3)

M4 x 12mm (x4)

M4 x 16mm (x4)

M4 x 20mm (x4)

Mounting

Head

Base Plate



Arm Assembly

(with pre-assembled Desk Clamp)



Phillips Head Screwdriver

Power drill

8mm (5/16”) drill bit

Desk | Single

Cable Covers

(x2 sets)

M5 x 12mm (x4)

M5 x 16mm (x4)







 

! The L-PB and L-PW support weights ranging from of 2kg (minimum) - 8kg (maximum) (4.4 - 17.6lbs).

! This product supports VESA mounting hole configurations 75 x 75mm and 100 x 100mm.

! The manufacturer accepts no responsibility for incorrect installation.

Check you have received all parts against the Component Checklist and Hardware.



Insert

Brake Pin

Desk Clamp

5mm Allen

Key

Clamp Pad

Desk

Clamp





(clockwise)



Cover Plate

Work Surface

(top view)

Min. gap=18mm (0.71”)







Remove the Desk Clamp using the 5mm Allen Key supplied.

Install the Base Plate to replace the Desk Clamp

(no screw required).

 To correctly insert the Brake Pin, so that the head of the

Brake Pin is flush, the base and Lower Arm must be aligned as

shown above.

Drill an 8mm (5/16”) hole through the work surface where

you want the centre of the base to be.

The hole should be at least 55mm (2.17”) from any

work surface edge to allow for the diameter of the base.

 Select the appropriate length bolt, 45mm or 60mm

depending on the work surface thickness.

suits work

surface thickness between

14-28mm (0.5”-1.1”).

suits work

surface thickness between

29-43mm (1.1”-1.7”).



28mm (1.1”)



14mm (0.5”)



25mm (1”)



17mm (0.7”)



25mm (1”)



17mm (0.7”)



43mm (1.7”)



29mm (1.1”)

Use 1,2, or 3 Bolt Through Washers to provide a thread length

of 17mm minimum to 25mm maximum (0.7”-1”) protruding

above the work surface.

For work surfaces thicker than 43mm (1.7”), longer M8

bolts can be purchased from hardware stores.

 Align the centre of the base over the pre-drilled hole.

Using the hardware selected in B5 fasten the base to the work

surface.

The default base setup allows  of rotation of the Lower Arm

around the base. If you want to limit the Lower Arm rotation to

go to B2, if not skip to B3.



To limit the Lower Arm rotation to insert the Brake Pin (as

shown below). Then go to B3.

 Lift and support the weight of the Upper

and Lower Arms.

 Using the 5mm Allen Key supplied, tighten

the Upper and Lower Arm Tension Bolts until

the Arm Assembly supports its own weight.

Desk Clamp

5mm

Allen Key





(anti-clockwise)

Insert

Brake Pin



Base Plate

45mm or

60mm Bolt

Bolt Through

Washer

5mm Allen Key





(clockwise)



(clockwise)

Lower Arm

Tension Bolt

Upper Arm

Tension Bolt 

(anti-clockwise)





  (How do I remove the Monitor? See final page for help)

 Select appropriate Display Mounting Screws from hardware ‘BAG B’ to suit the

monitor, and fasten the Mounting Head to the back of the monitor.

 Align and locate the Mounting Head onto the mounting point

at the top of the arm assembly.

 To remove the monitor, refer to instructions on the final

page.

 If necessary adjust the swivel tension to increase head

stability. Use the 2mm Allen Key supplied.

Insert Security Screw to secure mounting head to Arm

Assembly





If the Mounting Holes are recessed into the

back of the monitor, or the monitor has

a curved rear panel, use the Spacer Bushes

supplied to pack the Mounting Holes.





 Push the Cover Plate over the

Mounting Head.

Press firmly around the inside edge

until you hear a ‘CLICK’.

2mm Allen

Key



(clockwise)



(anti-clockwise)

Mounting Head

Mounting point







Security Screw







Display Mounting

Screws (x4)

Cover Plate

Mounting Head

Mounting Hole

Spacer Bush (x4)

Display Mounting

Screws (x4)

Mounting Hole

M4x20mm



     (How do I remove Cable Covers? See final page for help)

 Push cables under retaining clips on the Upper and Lower

Arms to hold the cables in position.

 Install Cable Covers on both sides of the Upper and Lower

Arms.

 The Cable Covers are different for left and right sides.

 If necessary gently flex clips

A and C to hold the cable.

 Route cables along the length of the Arm

Assembly and connect to the monitor.

Leave enough slack in the cables to

allow full movement at the joints.

 If cable plugs are too big to fit through

the joints, route the cables on the outside.

Starting with the Lower Arm, tighten the Tension Bolt until the arm comfortably holds its

position wherever it is moved.

Once satisfied, repeat the process for the Upper Arm.

 FOR MULTIPLE INSTALLATIONS ONLY.

When tensioning the Upper and Lower Arms take

note of the Visual Gauge on each arm.

This will help when installing multiple Levitate

products supporting the same weight monitors.

 DO NOT OVER TENSION.

Both arms should move freely, and support

the weight of the monitor in any position.

 Position the Arm Assembly for 

 OR  use depending on your

monitor requirements.





(anti-clockwise)









 



Upper Arm

Lower Arm

Tension Bolt

Upper Arm

Tension Bolt

Visual Gauge



(clockwise)

 - Refer to the User Operator Guide for user adjustments



Rotate the monitor to Portrait or Landscape position

depending on user requirements.

The monitor will only rotate 90° clockwise from

the starting position (when facing the screen).

Tilt the monitor up or down to suit the user.

 Depending on the weight of the monitor, make

adjustments to the tilt tension using the 5mm Allen

Key if necessary.

5mm Allen

Key



(clockwise)



(anti-clockwise)



















 Remove the Security crew using a Phillips head

screwdriver.



(anti-clockwise)

 Using a paper clip or a ball point pen press in

the three tabs holding the Cable Cover in place.

 Pull the Cable Cover away from the Arm. Repeat this

process for each Cable Cover.



 Access the tabs through the three

pinholes nearest the Cable Cover you

want to remove (e.g. A,B,C).

 If you tightened the swivel tension in Step 5, loosen the

screw (do not remove) using the 2mm Allen Key supplied.

Lift the Monitor away from the Arm Assembly.

Mounting Head

2mm Allen

Key



(anti-clockwise)

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.

Due to the continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 25.10.12 ©

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Atdec Support et étagère

Atdec

Atdec AD-TVC-45 Manuel utilisateur

Atdec

Atdec AWM-AD Manuel utilisateur

Atdec

Atdec APA-B Manuel utilisateur

Atdec

Atdec AWMS-2-BT75-FS Manuel utilisateur

Atdec

Atdec AWM-A71 Manuel utilisateur

Atdec

Atdec VF-AT-NP Manuel utilisateur

Atdec

Atdec TH-1026-VF Manuel utilisateur

Atdec

Atdec AWM-A46-B Manuel utilisateur

Atdec

Atdec Levitate Instructions de fonctionnement

Atdec

Atdec SD-AT-DW Manuel utilisateur

Atdec

Atdec TH-1040-CTS Manuel utilisateur

Atdec

Atdec TH-3060-UF Manuel utilisateur

Atdec

Atdec AWM-W6 Manuel utilisateur

Atdec

Atdec Telehook Manuel utilisateur

Atdec

Atdec ADBS-3x1-30T3C Manuel utilisateur

Atdec

Atdec Freestanding Quad Manuel utilisateur

Atdec

Atdec SYSTEMA SW6S Manuel utilisateur

Atdec

Atdec TELEHOOK 12/30 Multi Manuel utilisateur

Atdec

Atdec ADBS-2x2-17MFB Manuel utilisateur

Atdec

Atdec VFS-DH Manuel utilisateur

Atdec

Atdec Visidec Focus Micro Instructions de fonctionnement

Atdec

Atdec AWM-LR Manuel utilisateur

Atdec

Atdec AWM-W35 Manuel utilisateur

Atdec

Atdec Telehook Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur