ARGON18 E-119 TRI+ Manuel utilisateur
E-119 TRI+ 284A: ASSEMBLY GUIDE
Valid for MY2019-2020 E-119 Tri+
Revision 4.0 - 02.13.2020
1
1. Tools Needed & First Ait Kit . . . . . . . . . . . . . . . . . . . . . . . .......2
2. Frameset Parts. . . . . . . . . . . . ...............................3
3. Seat Post Clamp Installation . . . . . . . . . . . . . . . . . . . . . . . . . .....5
4. Seat Post Installation. . . . . . . . . . . . . . . . . . . . . . . . . . ...........6
5. Frame Inspection ........................................8
6. Derailleur Hanger Adjustment. . . . . . . . . . . . . . . . . . . . . . . . ....9
7. Fork & Headset Installation..............................11
8. Front Brake Installation. . . . . . . . . . . . . . . . . . . . . . . . ..........13
9. Handlebar Installation ..................................21
10. Rear Brake Installation .................................26
11. Cable Housing Installation .............................34
12. Electronic Drive-train Specication .....................38
13. Armrest Installation. . . . . . . . . . . . . . . . . . . . . . . . ............41
14. Saddle Adjustment ....................................42
15. Top Tube Box Installation ..............................43
16. Tailwind Installation ...................................45
17. Troubleshooting / Tips .................................49
18. Parts’ SKUs and Descriptions ...........................50
19. Seat Post Min/Max insertion............................53
For the warranty to be valid, the bicycle must be fully assembled by an authorized Argon 18 dealer. High end components,
particularly carbon parts, need extra care when assembled. These components must be installed using a calibrated torque
wrench to make sure every bolt is at the right torque setting to prevent damage.
E-119 TRI+ 284A: Table of Contents
My E-119 Tri+
Date of purchase:
Retailler:
Size:
Serial Number:
2
Tools needed for assembly
1: Allen Key Set
2: Grease
3: Utility Pick Set (Park Tool Item # UP-SET)
4: Clean Rags
5: Derailleur Hanger Alignment Gauge (Park Tool Item # DAG-2)
6: Cables and Housing Cutter
7: Carbon Paste
8: 8mm Flat Wrench
9: 13mm Flat Wrench
10: Loctite #242 or #243
11: Torque Wrench + Hex bit
12: Long-nose Plier
First Aid Kit: Essential parts to always have on hand
IN CASE OF EMERGENCY…THIS MIGHT SAVE YOUR RIDE!
1: Spare rear dropout (SKU: 38883)
2: Spare brake pads corresponding to your wheel model (carbon or alloy)
3: Seat clamp (SKU: 80423, 80422)
IMPORTANT: the E-119 Tri+’s seat clamp (1.7) is not the same as the Nitrogen
E-119 TRI+ 284A: 1. Tools Needed & First Aid Kit
SKU: 38883
1.6 SKU: 80422
SKU: 80423
3
E-119 TRI+ 284A: 3. Frameset Parts
3
Images are for reference only. Proportions are not accurate.
Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.
*for more info please consult notice on Seatpost clamp dated 2016-06-09
80283
80164
80279 80080
38977 80061
80165
80878
80160 80280
80295
80303
80308
80281 80159
80297
80292
80293
36165
38975
80298
39000
SP.E119T+.284A
38883
38882
80167
80022
80023 80077
80629
80078
80294
80301
80302
80306
80305
80304
80307
80296
38916
38912
80382
80299
38997 38998 38999
39001
FK.E119T+.XS.284A
FK.E119T+.S.284A
FK.E119T+.M.284A
FK.E119T+.L.284A
FK.E119T+.XL.284A
80422
80164
80650
38934
38911
38915
39108
80630
81041 81039
81040
80423
80492
XS-S / 80289
M / 80290
L / 80291
XL / 80767
4
E-119 TRI+ 284A: 3. Frameset Parts
80402 80401
SP.E119T+.284A
80429 80009
8042880025, 80400
80429
Images are for reference only. Proportions are not accurate.
Argon 18 reserves the right to modify/change parts of the frameset at any moment without prior notice.
5
E-119 TRI+ 284A: 4. Seat Post Clamp Installation
1. Apply a drop of blue Threadlocker
(n. 242) on the bolt’s thread
2. Apply grease on the seat post clamp
and on the screws as shown
3. Assemble the seat post clamp with the
small screw, allowing the parts to move
freely
4. Place the seat post collar inside the
frame, holding it to prevent it falling
inside the frame
5. Insert the seatpost, on which some
carbon ber assembly paste has been
applied
6. Position the seatpost to the desired
height
7. Tighten the set screw at max. 5.5Nm
IMPORTANT: The E-119 Tri+’s seat clamp
is not the same as the Nitrogen
GREASE
GREASE
LOCTITE
GREASE
CARBON FIBER
ASSEMBLY
COMPOSITE
5.5 Nm
1Nm
1.7.1
RUNNING CHANGE
B
A
C
6
E-119 TRI+ 284A: 5. Seat Post Installation
1. Unscrew main bolt (A) as far as
possible without fully removing from
the lock nut.
2. Install the saddle rails into the
seatpost clamp (B).
3. Slide saddle clamp (B) onto rocker (C).
4. Tighten the bolt up at 12Nm.
See p.43 for saddle adjustment.
IMPORTANT:
The E-119 Tri+’s saddle rail clamp is
made for aluminum and round-shaped
saddle rails ( For part numbers contact
Ritchey).
For other types of saddle rails, please
refer to the Tips and Troubleshooting
section of this Assembly Guide (p.50).
12Nm
GRIP PASTE
GRIP PASTE
6Nm
6Nm
3.2
7
E-119 TRI+ 284A: 5. Seat Post Installation
The Di2 battery is hidden in the
seatpost; use the Di2 battery holder
(3.2) to x the battery correctly. Apply a
slight amount of grease on both parts.
GREASE
GREASE
8
E-119 TRI+ 284A: 6. Frame Inspection
Parts installed on the frame Description Screw Torque Detail
type Nm
1 Front derailleur hanger Screw (2) 5mm 4Nm Loctite
2 Rear derailleur hanger Screw (2) 3mm 4Nm Loctite
3 Bottle cage Screw (5) 4mm 3Nm Grease
4 Bottom bracket cover Screw (2) 4mm 2.5Nm Grease
5 Brake arms pivot (front / rear) Screw (2) 6mm 7Nm Loctite
6 Front brake cap Screw (2) 4mm 2.5Nm Grease
7 Rear brake cap Screw (2) 4mm 5Nm Grease
IMPORTANT:
The following parts are assembled on the frame. When assembling the bike, you will need to adjust these parts according to their
torque specications.
1. Brakes and gears cables and housing set
2: Frameset parts checklist (see p.51)
3: Inspect the frame for cosmetic aspect (scratches, bumps, cracks, paint defect, etc.)
4: For reference, check serial number and write it on p.1
5: All the necessary bolts (refer to Frameset Parts, p.4)
6: For optimal shifting performance, use a dropout alignment gauge to make sure that the drive-side dropout is
straight
9
E-119 TRI+ 284A: 7. Derailleur Hanger Adjustment
1. Ensure that the dropout is aligned.
2. Use Derailleur Hanger Alignment Gauge like ParkTool
Item # DAG-2.
For any assistance, visit ParkTool’s website:
parktool.com/product/derailleur-hanger-align-
ment-gauge-dag-2
4Nm
4Nm
1.6
Autres manuels pour E-119 TRI+
4
Table des matières
Autres manuels ARGON18 Vélo
ARGON18
ARGON18 Dark Matter Manuel utilisateur
ARGON18
ARGON18 E-118 NEXT Manuel utilisateur
ARGON18
ARGON18 E-117 TRI Disc 317A Manuel utilisateur
ARGON18
ARGON18 GALLIUM PRO DISC 338A 2021 Manuel utilisateur
ARGON18
ARGON18 KRYPTON Manuel utilisateur
ARGON18
ARGON18 E-117 TRI 285A Manuel utilisateur
ARGON18
ARGON18 Grey Matter Manuel utilisateur
ARGON18
ARGON18 GALLIUM 279A Manuel utilisateur
ARGON18
ARGON18 DARK MATTER 282A Manuel utilisateur
ARGON18
ARGON18 GALLIUM PRO 347A Manuel utilisateur
ARGON18
ARGON18 nitrogen Manuel utilisateur
ARGON18
ARGON18 KRYPTON X ROAD Manuel utilisateur
ARGON18
ARGON18 E-80 Manuel utilisateur
ARGON18
ARGON18 GALLIUM PRO DISC 338A Manuel utilisateur
ARGON18
ARGON18 E-119 TRI+ Manuel utilisateur
ARGON18
ARGON18 NITROGEN Manuel utilisateur
ARGON18
ARGON18 GALLIUM CS DISC 322A Manuel utilisateur
ARGON18
ARGON18 GALLIUM DISC 339A 2021 Manuel utilisateur
ARGON18
ARGON18 E-118 TRI+ Disc 315A Manuel utilisateur
ARGON18
ARGON18 SUM PRO 2022 Manuel utilisateur
