Anritsu S331E Manuel utilisateur
Maintenance Manual
Site Master
Cable and Antenna Analyzer with
Spectrum Analyzer
S331E, 2 MHz to 4 GHz
S332E, 2 MHz to 4 GHz, Spectrum Analyzer, 9 kHz to 4 GHz
S361E, 2 MHz to 6 GHz
S362E, 2 MHz to 6 GHz, Spectrum Analyzer, 9 kHz to 6 GHz
Anritsu Company
490 Jarvis Drive
Morgan Hill, CA 95037-2809
USA
Part Number: 10580-00253
Revision: J
Published: May 2016
Copyright 2010, 2016 Anritsu Company
TRADEMARK ACKNOWLEDGMENTS
Windows, Windows XP, and Windows Vista are all registered trademarks of Microsoft Corporation.
Acrobat Reader is a registered trademark of Adobe Corporation.
Site Master is a trademark of Anritsu Company.
NOTICE
Anritsu Company has prepared this manual for use by Anritsu Company personnel and customers as a guide for the
proper installation, operation and maintenance of Anritsu Company equipment and computer programs. The
drawings, specifications, and information contained herein are the property of Anritsu Company, and any
unauthorized use or disclosure of these drawings, specifications, and information is prohibited; they shall not be
reproduced, copied, or used in whole or in part as the basis for manufacture or sale of the equipment or software
programs without the prior written consent of Anritsu Company.
UPDATES
Updates, if any, can be downloaded from the Documents area of the Anritsu Website at:
http://www.anritsu.com
For the latest service and sales contact information in your area, please visit:
http://www.anritsu.com/contact.asp
S3xxE MM PN: 10580-00253 Rev. J Safety-1
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Company uses the
following symbols to indicate safety-related information. For your own safety, please read the information
carefully before operating the equipment.
Symbols Used in Manuals
Safety Symbols Used on Equipment and in Manuals
The following safety symbols are used inside or on the equipment near operation locations to provide
information about safety items and operation precautions. Ensure that you clearly understand the meanings of
the symbols and take the necessary precautions before operating the equipment. Some or all of the following
five symbols may or may not be used on all Anritsu equipment. In addition, there may be other labels attached
to products that are not shown in the diagrams in this manual.
Danger
This indicates a risk from a very dangerous condition or procedure that could result in
serious injury or death and possible loss related to equipment malfunction. Follow all
precautions and procedures to minimize this risk.
Warning This indicates a risk from a hazardous condition or procedure that could result in
light-to-severe injury or loss related to equipment malfunction. Follow all precautions
and procedures to minimize this risk.
Caution
This indicates a risk from a hazardous procedure that could result in loss related to
equipment malfunction. Follow all precautions and procedures to minimize this risk.
This indicates a prohibited operation. The prohibited operation is indicated symbolically
in or near the barred circle.
This indicates a compulsory safety precaution. The required operation is indicated
symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or near
the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
Safety-2 PN: 10580-00253 Rev. J S3xxE MM
For Safety
Warning Always refer to the operation manual when working near locations at which
the alert mark, shown on the left, is attached. If the operation, etc., is
performed without heeding the advice in the operation manual, there is a
risk of personal injury. In addition, the equipment performance may be
reduced.
Moreover, this alert mark is sometimes used with other marks and
descriptions indicating other dangers.
Warning
When supplying power to this equipment, connect the accessory 3-pin
power cord to a 3-pin grounded power outlet. If a grounded 3-pin outlet is
not available, use a conversion adapter and ground the green wire, or
connect the frame ground on the rear panel of the equipment to ground. If
power is supplied without grounding the equipment, there is a risk of
receiving a severe or fatal electric shock.
Warning
This equipment can not be repaired by the operator. Do not attempt to
remove the equipment covers or to disassemble internal components.
Only qualified service technicians with a knowledge of electrical fire and
shock hazards should service this equipment. There are high-voltage parts
in this equipment presenting a risk of severe injury or fatal electric shock to
untrained personnel. In addition, there is a risk of damage to precision
components.
Warning
Use two or more people to lift and move this equipment, or use an
equipment cart. There is a risk of back injury if this equipment is lifted by
one person.
Caution
Electrostatic Discharge (ESD) can damage the highly sensitive circuits in
the instrument. ESD is most likely to occur as test devices are being
connected to, or disconnected from, the instrument’s front and rear panel
ports and connectors. You can protect the instrument and test devices by
wearing a static-discharge wristband. Alternatively, you can ground
yourself to discharge any static charge by touching the outer chassis of the
grounded instrument before touching the instrument’s front and rear panel
ports and connectors. Avoid touching the test port center conductors
unless you are properly grounded and have eliminated the possibility of
static discharge.
Repair of damage that is found to be caused by electrostatic discharge is
not covered under warranty.
S3xxE MM PN: 10580-00253 Rev. J Safety-3
For Safety
Warning
This equipment is supplied with a rechargeable battery that could potentially leak hazardous
compounds into the environment. These hazardous compounds present a risk of injury or loss
due to exposure. Anritsu Company recommends removing the battery for long-term storage of
the instrument and storing the battery in a leak-proof, plastic container. Follow the
environmental storage requirements specified in the product data sheet.
Safety-4 PN: 10580-00253 Rev. J S3xxE MM
Autres manuels pour S331E
1
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Anritsu Instrument de mesure
Anritsu
Anritsu MS2024A/MS2026A Manuel utilisateur
Anritsu
Anritsu MT8220A Manuel utilisateur
Anritsu
Anritsu MT9085 Series Manuel d'instructions
Anritsu
Anritsu Spectrum Master MS2721B Manuel utilisateur
Anritsu
Anritsu 54100A Series Instructions d'installation et d'utilisation
Anritsu
Anritsu Bit Master MP1026B Manuel du propriétaire
Anritsu
Anritsu Spectrum Master MS2720T Manuel utilisateur
Anritsu
Anritsu ShockLine MS46121A Series Manuel du propriétaire
Anritsu
Anritsu Network Master MT9090A Series Manuel utilisateur
Anritsu
Anritsu MS2711A Manuel utilisateur
Anritsu
Anritsu Spectrum Master MS2721B Manuel utilisateur
Anritsu
Anritsu ShockLine MS46131A-010 Manuel utilisateur
Anritsu
Anritsu MS2711B Manuel utilisateur
Anritsu
Anritsu ShockLine ME7868A Manuel utilisateur
Anritsu
Anritsu MS2690A Manuel utilisateur
Anritsu
Anritsu Network Master MU909020A Manuel utilisateur
Anritsu
Anritsu CMA50 Manuel utilisateur
Anritsu
Anritsu MS2722C Manuel utilisateur
Anritsu
Anritsu 37 C Series Manuel utilisateur
Anritsu
Anritsu 37 D Series Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur