Analog Devices ADSP-CM419F Manuel utilisateur

ADSP-CM419F CPA

Manual

Revision 1.0, Jan 2018

Part Number

20_047150

Analog Devices, Inc.

One Technology Way

Norwood, MA 02062-9106

without prior, express written consent from Analog Devices, Inc.

Printed in the USA.

Disclaimer

Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Ana-

log Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its

use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is

granted by implication or otherwise under the patent rights of Analog Devices, Inc.

Trademark and Service Mark Notice

The Analog Devices logo, Blackfin, Blackfin+, SHARC, SHARC+, CrossCore, VisualDSP++, EZ-KIT, EZ-Extend-

er, and EngineerZone are registered trademarks of Analog Devices, Inc.

All other brand and product names are trademarks or service marks of their respective owners.

Regulatory Compliance

The CPA(Control Processor Assembly) is designed to be used solely in a laboratory environment. The board is not

intended for use as a consumer-end product or as a portion of a consumer-end product. The board is an open

system

design, which does not include a shielded enclosure and, therefore, may cause interference to other electrical

devices

in close proximity. This board should not be used in or near any medical equipment or RF devices.

The CPABoardcontains ESD (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the

human body and equipment and can discharge without detection. Permanent damage may occur

on devices

subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or

loss of functionality. Store unused boards in the protective shipping package.

Contents

Preface

Contents

Copyright Information .................................................................................................................................. 2

Regulatory Compliance................................................................................................................................. 2

Contents ...................................................................................................................................................... 4

1Preface................................................................................................................................................ 6

Purpose of This Manual........................................................................................................................ 6

Intended Audience ............................................................................................................................... 6

Technical Support................................................................................................................................. 7

Supported Processors........................................................................................................................... 8

Supported Tools ................................................................................................................................... 8

Product Information............................................................................................................................. 8

Package Contents................................................................................................................................. 9

2 CPA Setup.......................................................................................................................................... 10

Product Overview............................................................................................................................... 10

Default Configuration......................................................................................................................... 11

Block Diagram .................................................................................................................................... 12

Analog Input Channel Selection .......................................................................................................... 13

Power Architecture............................................................................................................................. 14

64M-bit Serial Flash Memory with Dual and Quad SPI (W25Q64) ........................................................ 15

USB to UART (FT232R) ........................................................................................................................ 15

Dual channel Digital Isolator –5K RMS (ADuM2281) ........................................................................... 16

5 kV digital Isolator with 5V DC-to-DC (ADUM6201)............................................................................ 17

TFT LCD ....................................................................................................................................................... 18

3Hardware Reference................................................................................................................ 19

System Architecture .......................................................................................................................... 19

Reset Pushbutton ( RES) .................................................................................................................. 20

GPIO Pushbuttons (SW A to E) ......................................................................................................... 21

LED Enable ( S705)............................................................................................................................ 22

Boot Mode Select (JP1).................................................................................................................... 22

VDD_INT Regulator.......................................................................................................................... 23

VREF Source (JP500) ........................................................................................................................ 24

ADC VINx ......................................................................................................................................... 24

Main Power Select ( JP200)............................................................................................................... 25

Power (LED1) ................................................................................................................................... 25

Reset (LED4)..................................................................................................................................... 25

Fault (LED5) ..................................................................................................................................... 25

Clock................................................................................................................................................ 26

LCD.................................................................................................................................................. 27

Character Display ( J21) ................................................................................................................... 27

Debug ( X602) ................................................................................................................................. 27

USB ( P3) ......................................................................................................................................... 27

1Preface

Thank you for purchasing the Analog Devices, Inc. CPA development Board evaluation system.

The ADSP-CM419F processor is based on the ARM® Cortex®-M4 processor core with floating point unit

operating at frequencies up to 240 MHz core clock, and the ARM® Cortex-M0 TM processor core operating at

frequencies up to

100 MHz system clock. The processors integrate up to 192K Bytes of SRAM memory with ECC,

up to 1M Byte of flash memory with ECC, accelerators and peripherals optimized for motor control and photo-

voltaic (PV) inverter control, and an analog front end consisting of up to two 6 times simultaneous sampling 16-bit

SAR-type ADCs, one 14-bit SAR

monitor ADC and one 12-bit DAC. The CPA board ships with all of the

necessary hardware to get you up and running and start the evaluation immediately.

The CPA contains an analog interface and digital interface. The evaluation board is designed to be used in

conjunction with the IAR Embedded Workbench®and Segger®

development environment for advanced application

code development and debug such as:

•Create, compile, assemble, and link application programs written in C++, C, and assembly

•Load, run, step, halt, and set breakpoints in application programs

•Read and write data and program memory

•Read and write core and peripheral registers

However it can work with other development environments like Eclipse\Gcc etc.

Purpose of This Manual

This manual provides instructions for installing the product hardware (board). The text describes operation and

configuration of the board components and provides guidelines for running code on the board.

Intended Audience

The primary audience for this manual is a programmer who is familiar with an ARM Cortex-M4 core. The ADSP-

CM41x family of mixed-signal control processors is based on the ARM Cortex-M4 core.

For additional information about the Analog Devices processor, see the Hardware Reference Manual. The document

describes the core and memory architecture of the ADSP-CM41x processor, but does not provide detailed

programming information for the ARM core.

The applicable documentation for programming the ARM Cortex-M4 core includes:

•

Cortex-M4 Devices Generic User Guide

•

CoreSight ETM-M4 Technical Reference Manual

•

Cortex-M4 Technical Reference Manual

For more information about programming the ARM core, visit the ARM Information Center:

http://infocenter.arm.com/help/.

Technical Support

You can reach Analog Devices processors and DSP technical support in the following way

•Post your questions in the processors and DSP support community at EngineerZone®:

http://ez.analog.com/community/dsp

•Submit your questions to technical support directly at:

http://www.analog.com/support

•E-mail your questions about processors, DSPs, and tools development software from CrossCoreEmbeddedStu-

dio

VisualDSP++

If using CrossCore Embeded Studio or VisualDSP++ choose Help> EmailSupport. This creates an e-mail to

processor.tools.support@analog.com and automatically attaches your CrossCore Embedded Studio or Visu-

alDSP++ version information and license.dat file.

•E-mail your questions about processors and processor applications to:

processor.tools.support@analog.com

processor.china@analog.com

•Contact your Analog Devices sales office or authorized distributor. Locate one at:

http://www.analog.com/adi-sales

•Send questions by mail to:

Analog Devices, Inc.

One Technology Way

P.O. Box 9106

Norwood, MA 02062-9106

USA

Supported Processors

This evaluation system supports the Analog Devices ADSP-CM419Fprocessor.

Supported Tools

Information about code development tools for the ADSP-CM419F and ADSP-CM41x family of processors is

available at:

http://www.analog.com/ADSPCM419FEZKIT

Product Information

Product information can be obtained from the Analog Devices Website

Analog Devices Website

The Analog Devices website, http://www.analog.com, provides information about a broad range of products - analog

integrated circuits, amplifiers, converters, and digital signal processors.

Toaccess a complete technical library for each processor family, go to http://www.analog.com/processors/techni-

cal_library. The manuals selection opens a list of current manuals related to the product as well as a link to the

previous revisions of the manuals. When locating your manual title, note a possible errata check mark next to the

title that leads to the current correction report against the manual.

Also note, MyAnalog.com is a free feature of the Analog Devices website that allows customization of a web page to

display only the latest information about products you are interested in. You can choose to receive weekly e-mail

notifications containing updates to the web pages that meet your interests, including documentation errata against

all manuals. MyAnalog.com provides access to books, application notes, data sheets, code examples, and more.

Visit MyAnalog.com to sign up. If you are a registered user, just log on. Your user name is your e-mail address.

EngineerZone

EngineerZone is a technical support forum from Analog Devices, Inc. It allows you direct access to ADI technical

support engineers. You can search FAQs and technical information to get quick answers to your embedded

processing and DSP design questions.

Use EngineerZone to connect with other DSP developers who face similar design challenges. You can also use this

open forum to share knowledge and collaborate with the ADI support team and your peers. Visit http://

ez.analog.com to sign up.

Package Contents

YourADSP-CM419F basedCPAboardpackage contains the following items.

ADSP-CM419F CPA board

2. USB 2.0 type A to mini-B cable (x2)

3. J-Link Lite emulator

2 CPA Setup

This chapter provides information on the major components and peripherals on the board along with instructions

for installing and setting up the evaluation software.

Product Overview

The board features:

•Analog Devices ADSP-CM419F processor 212 ball BGA

•16MHz and 30 MHz oscillators

•Analog Devices Unity-Gain Stable, Ultralow Distortion, 1 nV/√Hz Voltage Noise, High Speed Op Amp

(AD8639)

•SPI Flash (SPI0) chip

•Microchip 64 MB QSPI Serial Flash (W25Q64FVSSiG)

•FTDI USB to UART (FT232R)

•Double Isolation through ADuM2281 Digital isolator and the ADuM6201 Digital isolator with isopower.

•Debug (JTAG/SWD/SWO) interface

•J-Link Lite emulator

•JTAG/SWD/SWO 20-pin 0.05” header

•Analogconnector

•ADC

•AGND/GND/VREF/5V

•Digital connector

•

PWM0-2

•

SINC0

•SPI1

•

SPORT0

•

TWI0

•

TMR0

•GPIOs

•

CNT0-3

•RESET

•

GND

/3.3V/5V output

Autres manuels pour ADSP-CM419F

Table des matières

Autres manuels Analog Devices Matériel informatique

Analog Devices

Analog Devices EVAL-ADPD6000 Manuel utilisateur

Analog Devices

Analog Devices SHARC ADSP-21368 Guide d'application

Analog Devices

Analog Devices EZ-KIT LITE ADSP-2191 Manuel utilisateur

Analog Devices

Analog Devices LINEAR DC2672A-A Guide de configuration rapide

Analog Devices

Analog Devices ADPA1105-EVALZ Manuel utilisateur

Analog Devices

Analog Devices Linear LT3383 Guide de configuration rapide

Analog Devices

Analog Devices AD9739 Manuel utilisateur

Analog Devices

Analog Devices SHARC ADSP-2136 Series Guide d'application

Analog Devices

Analog Devices DC2745A Guide de configuration rapide

Analog Devices

Analog Devices ADP1046A Manuel utilisateur

Analog Devices

Analog Devices LTM4683 Manuel utilisateur

Analog Devices

Analog Devices Linear ADI Power LTC3310-1 Manuel utilisateur

Analog Devices

Analog Devices EVAL-ADAU1860 Manuel utilisateur

Analog Devices

Analog Devices Linear DC2331A-A Guide de configuration rapide

Analog Devices

Analog Devices AD9883A Manuel utilisateur

Analog Devices

Analog Devices SHARC ADSP-21367 Manuel utilisateur

Analog Devices

Analog Devices AD9866 Manuel utilisateur

Analog Devices

Analog Devices EVAL-ADuCM420QSP1Z Manuel utilisateur

Analog Devices

Analog Devices iSensor ADIS/EVAL/USB Manuel d'instructions

Analog Devices

Analog Devices ADT7473 Manuel utilisateur

Analog Devices

Analog Devices MAX22005 Manuel utilisateur

Analog Devices

Analog Devices ADM8611 Manuel utilisateur

Analog Devices

Analog Devices EVAL-AD7606SDZ Manuel utilisateur

Analog Devices

Analog Devices LTC5597 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur