Alfalaval REMIND EPC 50 Manuel utilisateur

Alfa Laval Marine & Power

REMIND™ EPC 50 Network

User´s Manual

Product No.

Printed

Book No.

31830-6410-1

Jan 2001

493107611 (3-1)

Alfa Laval reserve the right to make changes at any time without

prior notice.

Any comments regarding possible errors and omissions or

suggestions for improvement of this publication would be

gratefully appreciated.

Copies of this publication can be ordered from your local Alfa

Laval company.

Published by: Alfa Laval Marine & Power AB

S - 147 80 Tumba

Sweden

493107611 (3-1)

1Scope 5

2 Introduction 7

2.1 Requirements 7

3 Software Installation 9

4 General about

SattBus installation 11

5 Hardware Installation 13

5.1 Overview 13

5.2 Connect a PC to EPC50 Control

Cabinet using a SattBus

PC Board 14

5.3 Connect a PC to EPC50 Control

Cabinet using a SattBus Serial

Unit, SBSU 17

6 Interconnect several

EPC50 units 21

7 HELP Documentation 25

8 Troubleshooting the

Network 27

8.1 Troubleshooting the PC Board

Network 27

8.2 Troubleshooting the SBSU

Network 28

9 Drawings and Figures 31

10 Parts List 33

11 SattBus PC-board

Description 35

11.1 Layout and Settings 35

12 SattBus Serial Unit,

SBSU Description 39

12.1 Mechanical Design 41

12.2 LED Indicators 41

12.3 Switches 41

12.4 Installation 42

12.5 Switch Settings 43

12.6 Technical Specifications 47

Contents

493107611 (3-1)

493107611 (3-1) 5

1 Scope

This manual is valid for Alfa Laval REMIND™

EPC 50 program, version 1.0 and for connection

of a PC to EPC 50 Control Systems.

The manual is intended for personnel with good

process knowledge and those who are operating

Separating Units with EPC 50 Control System.

1 Scope REMIND™ EPC 50 Network User´s Manual

6493107611 (3-1)

493107611 (3-1) 7

2 Introduction

REMIND™ EPC 50 Network, is an Alfa

Laval software specifically designed for

supervision and remote control of separation

units with EPC 50 Control System. With the

EPC 50 Control System in remote mode, you

can supervise and control the separator units

from a personal computer, PC, placed in a

control room.

2.1 Requirements

The program REMIND™ EPC 50 Network

will run on a PC which meets the following

requirements:

•Processor at least Pentium 200 MHz with

16 Mbyte RAM (32 Mbye is

recommended) and 30 Mbyte hard disk

space available.

•Operating system Windows 95 and later or

Windows NT 4.00 and later.

•One free RS232 COM-port or one free

ISA PC slot.

Warning! Before carrying out any operation that

may effect the EPC 50, take steps to ensure that

no injury to personnel or damage to equipment

can occur as a result of the changes.

2 Introduction REMIND™ EPC 50 Network User´s Manual

8493107611 (3-1)

REMIND™ EPC 50 Network User´s Manual 3 Software Installation

493107611 (3-1) 9

3 Software

Installation

This chapter describes how to install

REMIND™ EPC 50 software in your PC. The

installation program is contained on two

diskettes.

The program requires Windows 95 and later

or Windows NT 4.00 and later.

The installation can be aborted at any time by

clicking the button CANCEL.

The installation procedure

When installing the REMIND™ EPC 50

software, proceed as follows:

1. Insert "REMIND™ EPC 50 Network"

disk 1 into drive a:

Note1. Other PC applications should be

closed before installation.

Note 2. When requested, insert diskette no. 2.

2. Select Run... from the Start Menu.

3. Welcome" dialog box appears

Click the next button.

Fill in ”User information”

4. Click the button "Next". The dialog box

"Choose Destination Location" appears.

The recommended (default) volume and

directory path for the REMIND™ EPC 50

program is

C:\Program Files\Remind\EPC 50\Network

Click the button "Browse" if another path is

requested and enter volume an directory. Click

on "OK" to confirm the selected path.

493-1077-11 (0-3) 11

4 General about SattBus installation

A shielded twisted pair cable with a minimum

of 3 twists/m and 80–120 Ωcharacteristic

impedance should be used as the bus cable.

Minimum area is 0.35 mm 2.

Note! The same type of cable must be used for

the entire SattBus installation.

Cable length and number of nodes

The total length must not exceed 500 m.

Termination

The bus cable should be terminated with

100 Ωresistors, connected at the two most

remote ends, measured along the cable. See

figure above.

All units in EPC 50 system, i.e. OP, I/O and

MT 50, have internal termination resistors

which can be connected/disconnected by

jumpers.

For EPC 50 I/O-board termination resistor is

connected by placing jumper XJ3 in position

TERM.

I/O Board

Termination resistor connected

when XJ3 in this position

TERM

XJ3

OPEN

Table des matières

Autres manuels Alfalaval Unité de contrôle

Alfalaval

Alfalaval SB Manuel utilisateur

Alfalaval

Alfalaval Unique SSV Series Manuel utilisateur

Alfalaval

Alfalaval SMP-BCA Manuel utilisateur

Alfalaval

Alfalaval Unique Mixproof LP Manuel utilisateur

Alfalaval

Alfalaval S946 Guide de l'utilisateur

Alfalaval

Alfalaval MCE2035 Manuel utilisateur

Alfalaval

Alfalaval 660 Manuel utilisateur

Alfalaval

Alfalaval Unique SSV PN10 Manuel utilisateur

Alfalaval

Alfalaval Unique SSV PN10 Manuel utilisateur

Alfalaval

Alfalaval Unique RV-ST Manuel utilisateur

Alfalaval

Alfalaval ThinkTop Digital 8-30 VDC PNP/NPN Manuel utilisateur

Alfalaval

Alfalaval Aseptic Mixproof Series Manuel utilisateur

Alfalaval

Alfalaval Unique PMO Plus Series Manuel utilisateur

Alfalaval

Alfalaval Unique SSV Manuel utilisateur

Alfalaval

Alfalaval SRC Manuel utilisateur

Alfalaval

Alfalaval SB Manuel utilisateur

Alfalaval

Alfalaval ThinkTop V70 Manuel utilisateur

Alfalaval

Alfalaval SMP-BC Manuel utilisateur

Alfalaval

Alfalaval SBV Manuel utilisateur

Alfalaval

Alfalaval Unique Mixproof 3-body Manuel utilisateur

Alfalaval

Alfalaval Unique 7710 Manuel utilisateur

Alfalaval

Alfalaval Unique Mixproof CP-3 Manuel utilisateur

Alfalaval

Alfalaval Unique DV-ST UltraPure Instructions de fonctionnement

Alfalaval

Alfalaval Tri-Clover LKB UltraPure Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur